Installation Guide

ManualsBrandsBaldwin ManualsHardwareClassic Style Single Cylinder Keyed Entry Door Knob Set with Classic Rosette from the Estate Collection

Dummy Installation

Door Preparation

Dummy Function Keyed Entry Lockset Installation Remember Baldwin

Exploded Views Keyed Entry Locksets

Congratulations! Dummy Strike Preparation

The strike needs to be installed in relationship to the direction that doors

open. Whether the doors open in or out, the angled side of the latchbolt must

always face towards the stationary door when the active door is in the open

position. The strike is then positioned with the lip facing the curved side of

the latchbolt as illustrated.

Caution: Before proceeding with the Door

Preparation, refer to the Dummy Strike

Preparation Illustration to ensure that the

curved section of the strike is positioned prop-

erly. If your door is pre-bored proceed to Keyed

Entry Lockset Installation - Step 1. Fold the tem-

plate on the line and place on the door at the

exact height of the previously installed Keyed

Entry Lockset. If the door is beveled, place the

folded edge on the low side of the bevel as

shown in the illustration. Mark the door for the

face and edge bores.

Caution: Re-check bore hole

locations before drilling. Drill the

2-1/8" diameter face bore through

the door and the 1" diameter edge

bore 3-1/2" deep for a 2-3/8" back-

set or 3-7/8" deep for a 2-3/4" back-

set. The dummy latch accommo-

dates both size backsets.

Align the strike and trace an out-

line onto the door frame using the

mounting screw marks for loca-

tion.

At the screw marks, drill two 1/8"

diameter pilot holes for #8 x 3/4"

wood screws.

Chisel the area marked for the

strike in step 3 to a depth of

1/16" or until the strike is flush

with the door frame. Do not

install the strike at this time.

Now, press the dummy latch into the 1"

diameter hole. Install the strike with two

#8 x 3/4" wood screws.

Install the outside knob assembly so the

edges of the adapter engage the grooves

in the dummy latch.

Install the inside adapter with the spindle

V-groove on the bottom and fasten to the

outside knob assembly with two 10-24 x

1-1/4" machine screws.

Turn the rose onto the adapter until it is

firmly seated against the door surface.

Slide the inside knob onto the spindle

shaft and firmly tighten the set screw.

Template

Inside Knob

Rose

Inside Adapter

Spindle Shaft

Outside Knob Assembly

Angled Side

Inside Adapter

Dummy Latch

Strike

10-24 x 1-1/4" Machine Screws

Set Screw

V-groove

Set Screw

Edges

Grooves

Latch

Drill 1/8" dia

pilot holes for

#8 screws.

With your purchase of this solid brass lockset, you’re among a group of

discerning individuals who know the intrinsic value of selecting the finest –

Baldwin.

Our step-by-step installation instructions will help guide you through your

project quickly and easily.

Before you begin your installation, read and understand the installation

instructions and marking templates. If you have any questions, please do

not hesitate to contact our Baldwin Technical Services Department at

1-800-566-1986. We’re here to help!

We thank you for your purchase and wish you the fullest enjoyment of your

Baldwin lockset.

Technical Services Support

1-800-566-1986

Hours: 6am to Midnight C.S.T. - 7 days a week.

Keyed Entry Locksets

Installation Instructions

P.O. Box 15048 Reading, PA 19612

PK-1138T (6/99)

1 2 3 4

7 8

With the completion of your

project, remember that

Baldwin quality hardware and

giftware products are avail-

able for all your decorating

and remodeling needs.

Matching entrance sets for

exterior doors, beautiful bath

accessories, and a complete

selection of cabinet and door-

enhancing hardware are all

available from your Baldwin

retailer.

Your Baldwin lockset is now ready for a

lifetime of use. Guaranteed!

PK- 1138T (6/99)

BALDWIN

TEAR HERE FOR ENGLISH INSTALLATION