Baldor Series 15H and 18H Inverter and Vector Drives
The Baldor Keypad The Baldor keypad allows the operator to enjoy the flexibility expected in today’s controls and the ease of operation you have always hoped to have. Baldor includes twelve keys on the keypad and the keys depress so you “feel” that you have pushed them. We also include a 32 character English “alpha-numeric” display. You don’t have to be a detective to know what you are doing - the display helps you whether you are operating, programming or monitoring.
Series 15H and 18H Applications Centrifugal Fan – The Baldor inverter is used to adjust the CFM (and associated pressure) of a fan. Typically, in the past, inlet vanes and outlet dampers have controlled air flow. These techniques are effective and well accepted, but not very energy efficient. With the Baldor inverter – vanes, dampers,actuators and their associated maintenance may be eliminated. Additionally and most importantly, power consumption is decreased by the cube of the speed decrease.
Series 15H Inverter Drive Design Specifications Operator Keypad • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Microprocessor controlled PWM output Output frequency 0.25-120Hz, optional 0.
Series 15H Inverter Drive Output Ratings With Quad Rating each control can be setup to operate in one of four distinct output operating zones. The zones are defined by the PWM frequency, continuous output current, and peak output current. By selecting the desired Operating Zone the control will automatically set the PWM frequency, continuous current, and peak current to the proper values for the desired operating zone.
Typical Inverter Drive Remote Control Connections Operation Mode: Standard run - 3 wire control J4 1 ANALOG GND 2 ANALOG INPUT #1 3 POT REFERENCE 4 ANALOG INPUT+ #2 5 ANALOG INPUT - #2 PROGRAMMABLE 0-5V OUTPUT (FACTORY SETTING: SPEED) 6 ANALOG OUT 1 PROGRAMMABLE 0-5V OUTPUT (FACTORY SETTING: CURRENT) ENABLE 7 ANALOG OUT 2 8 INPUT #1 9 INPUT #2 10 INPUT #3 11 INPUT #4 12 INPUT #5 13 INPUT #6 14 INPUT #7 15 INPUT #8 16 INPUT #9 17 39 +24VDC 18 40 OPTO IN POWER 19 41 O
Series 15H Washdown Inverter Drive Baldor 15H Washdown Inverter controls provide variable torque, constant torque and constant horsepower control in a NEMA 4X enclosure that can withstand frequent washdowns. These controls may be used in new installations, replacements or original equipment. They have an output frequency of 0.25 to 120 Hz, with a programming option up to 400 Hz. Peak overload capacity is 150% for sixty seconds.
Series 18H Vector Drive Desing Specifications Operator Keypad • Programmable carrier frequency to 16KHz • Full rated torque down to zero speed • Automatic tuning to motor with manual override • Motor shaft orientation to encoder marker or switch closure • Process follow: ±10vdc, ±5vdc, 0-5vdc, 0-10vdc, 4-20mA, digital via keypad or optional RS-232, RS-485 serial communication • Programmable linear or S curve acceleration/deceleration • 15 Selectable preset speeds • Dynamic braking (optional 20 Hp+) • Faul
Series 18H Vector Drive Output Ratings With Quad Rating each control can be setup to operate in one of four distinct output operating zones. The zones are defined by the PWM frequency, continuous output current, and peak output current. By selecting the desired Operating Zone the control will automatically set the PWM frequency, continuous current, and peak current to the proper values for the desired operating zone.
Typical Vector Drive Remote Control Connections Bipolar Speed or Torque Control Operating Mode Shown 9 www.baldor.
Series 18H Washdown Vector Drive When used with a Baldor Washdown Vector Drive® motor, or other motors with a feedback device, Baldor 18H Washdown Vector controls provide precise positioning, speed control and holding torque, plus full-rated torque at zero speed. Ideal for food processing conveyor applications with load variations and frequent stop/starts. These controls may be used in new installations, replacements or original equipment.
Expansion and Accessory Boards Baldor offers a wide variety of plug-in expansion boards to allow the H Series controls to be interfaced with various inputs and outputs. One or two expansion boards may be mounted into the control to custom tailor the inputs, outputs, and feedback requirements to the application. Baldor also offers several expansion boards that will allow direct interfacing with popular PLC’s.
Profibus DP Communication Board - EXB014A01 Allows connection to Profibus DP communications bus. Uses plug in terminals for connection. Modbus Plus Communication Board - EXB015A01 Allows connection to Modbus Plus communications bus. Uses plug in terminals for connection. Group 1 and Group 2 Ordering/Mounting Information • NOTE: Expansion boards plug into the main control board inside the control. When using one expansion board, either a Group 1 or Group 2 board will connect to the main control board.
Dynamic Braking Resistor Assemblies (RGA) Dynamic Braking Resistor Assemblies include braking resistors completely assembled and mounted into a NEMA 1 enclosure. For 20 hp and above (-EO Controls), select the braking resistor from the table with the matching ohms for the RTA selected and adequate continuous watts capacity to meet load requirements.
Outline and Dimensions Z U JOG Ø.25 LOCAL PROG FW D DISP REV SHIFT ENTER STOP RESET X Y V .25 Size A B Dimensions - in. (mm) Outside Mounting Height(X) Width(V) Depth(Z) Height(Y) Width(U) 12.272 7.974 7.120 11.5 7.2 (312) (203) (181) (292) (183) 15.4 10.0 7.1 14.6 9.2 (391) (254) (180) (371) (234) Z U AIR OUTLET JOG Y LOCAL FWD DISP REV SHIFT STOP RESET PROG ENTER X V NOTE: Size C2, E and F controls can also be mounted in a thru wall configuration.
Contact your nearest Baldor District Office at these World Wide locations, or visit www.baldor.
