Specifications
AC Servo Drive Solutions
>
Ordering Information
Fan Tray
Provides forced air cooling for MicroFlex and MicroFlex e100.
Required if average current is above 3A RMS.
Catalog Number Description
FAN001-024 Fan tray for single MicroFlex
MicroFlex and MicroFlex e100
Catalog Number Description
FMH2A03TR-EN23
3A MicroFlex AC Servo Drive. RS232. Encoder
FMH2A06TR-EN23
6A MicroFlex AC Servo Drive. RS232. Encoder
FMH2A09TR-EN23
9A MicroFlex AC Servo Drive. RS232. Encoder
FMH2A03TR-RN23
3A MicroFlex AC Servo Drive. RS232. Resolver
FMH2A06TR-RN23
6A MicroFlex AC Servo Drive. RS232. Resolver
FMH2A09TR-RN23
9A MicroFlex AC Servo Drive. RS232. Resolver
MFE230A003
3A MicroFlex e100 ETHERNET Powerlink AC Servo Drive
MFE230A006
6A MicroFlex e100 ETHERNET Powerlink AC Servo Drive
MFE230A009
9A MicroFlex e100 ETHERNET Powerlink AC Servo Drive
EuroFlex
Catalog Number Description
EFL001-501
EuroFlex amplifier (5A/15A) - RS485 serial port
EFL001-502
EuroFlex amplifier (5A/15A) - RS232 serial port
BPL011-501
EuroFlex backplane
FI0015A02
EMC filter
1) MicroFlex: For RS485 feedback option, substitute the last 2 for a 4. For
example FMH2A03TR-EN23 becomes FMH2A03TR-EN43
2) Add /12 for the bulk pack option of 12 units
Series-II: FlexDrive, Flex+Drive, MintDrive
H A
T
2
-
Drive Family
Current Code
Input Voltage
Braking Options
Feedback Options
Bus Options
Logic Supply
MDH = MintDrive-II
FPH = Flex+Drive
FDH = FlexDrive
-II
-II
R = Requires external resistor
B = Built in regen resistor
R = Resolver
E = Encoder
D = Absolute Encoder (EnDat)
N = None
B = Dual CAN + Extra I/O
C = CANopen
D = DeviceNet
P = Profibus-DP
0 = Internally generated
3 = External customer
supplied +24 VDC
A02 = 2.5 Amps
A05 = 5 Amps
A07 = 7.5 Amps
A15 = 15 Amps
A20 = 20 Amps
A27 = 27 Amps
1 = 115 1
2 = 230 1
4 = 230-460 3
VAC
VAC 230V
VAC
AC 3
3 onlyf
}
Notes
Only available on single phase drives. Option 3
is recommended for Flex+Drive and MintDrive to
maintain position during machine stop conditions
Only provides CANopen and I/O on Flex+Drive-II.
Not supported on FlexDrive-II
Limited support on FlexDrive-II
Select B for 2.5 and 5.0A drives
2.5A models have internal 20W 175 ohm (single
phase) or 300W 200 ohm (3 phase) regen resistor
5.0A models have internal 20W 175 ohm (single
phase) or 300W 200 ohm (3 phase) regen resistor
Select R for all other drives
May increase width of drive. See Page 26
230VAC 3 phase drive available in 15A variant
only. Specify FDH2A15TR-RN23 for example.
Example Catalog Numbers:
FDH2A05TB-RN23 - FlexDrive 230VAC single phase,
5A, resolver feedback, external 24V. No options.
FPH2A15TR-ED23 - Flex+Drive 230VAC 3 phase, 15A,
encoder feedback, external 24V, DeviceNet option.
MDH4A15TR-EB23 - MintDrive 460VAC, 15A, encoder
feedback, external 24V, CANopen + I/O option.
Braking/Regen Resistors
Catalog Number Watts Matched Drive
RG56
44W 3A MicroFlex
RG39
100W 6A / 9A MicroFlex
7.5A Series-II drive
RG22
100W 115VAC 7.5A Series-II drive
RG68
320W 3 phase 7.5A Series-II drive
RG27A
320W 3 phase 15A Series-II drive
RG23
640W 3 phase 20A Series-II drive
RG11
640W 3 phase 27.5A Series-II drive
230VAC
1Ф
115VAC
1Ф
230VAC
3Ф
230-460VAC
3Ф
2.5A
FI0029A00*
FI0015A00 FI0015A00 FI0018A00
5A
FI0029A00*
FI0015A02 FI0015A02 FI0018A00
7.5A FI0029A00* FI0029A00* FI0018A00
15A FI0018A01 FI0018A01
20A FI0018A01
27.5A FI0018A01
230VAC
1Ф
230VAC
3Ф
3A
FI0029A00*
FI0015A00 FI0018A00
6A
FI0029A00*
FI0015A02 FI0018A00
9A FI0029A00* FI0018A03
Recommended filters for MicroFlex and MicroFlex e100
Recommended filters for Series-II drives
EMC Filter Selection Guide
* Footmount filter
Auxiliary I/O Breakout Board
For use with Bus Option B. Provides screw terminal connectors for I/O.
Catalog Number Description
OPT017-501
Auxiliary I/O breakout board
CBL022-502
Auxiliary I/O breakout board cable 2m (6ft)
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com