Specifications
13
CiA DS402 Positioning Drive Profile
The core architecture of the MicroFlex e100 is based on the CAN
in Automation (CiA) DS402 positioning drive profile. This describes
the drive behavior (by means of an object dictionary) and provides
the ability to perform basic positioning functions such as homing
cycles, incremental and absolute moves, change of target position
and profiled speed/torque control. This functionality, originally
designed for CANopen based control, has been adopted and
enhanced for use over ETHERNET Powerlink. The MicroFlex e100
can be controlled over its integrated CANopen port or Ethernet.
CANopen Manager Capability
The Microflex e100 has an integrated CAN port which can be
configured to act as a network manager. This provides a convenient
and powerful means to expand your system with CANopen I/O
devices conforming to CiA DS401 standards. Devices, such as
digital and analog input/output modules are managed by the drive,
but the I/O states are available to the Mint program running on the
NextMove e100, as if they were local to the controller.
Integrated Two Port Ethernet Hub
Connecting multiple devices on the Ethernet network is simplified
by an integrated 2 port hub. Simply daisy chain the connection to
the next device in the system.
Universal Encoder Interface
A unique feedback interface provides support for leading encoder
technology. Incremental encoders (with or without Hall-effect tracks),
EnDat 2.1/2.2 , SSI single or multi-turn absolute encoders and 1V
Sin/Cos encoders, are all supported as standard. This reduces
stocking and spares requirements and also ensures the capability
to utilize high performance feedback devices for optimum precision,
accuracy and smooth speed regulation.
Universal Power
Supply for a
Global Market
MicroFlex operates from
a single or three phase
supply, 115 to 230 VAC.
The control electronics
are maintained by
an external customer
supplied 24 VDC supply,
in the event of main AC
power removal. Useful for
typical safety schemes.
Digital I/O for Axis Functions
Three digital inputs provide typical drive and motion signals such
as home sensor and limit switches. Two of these can be used for
high speed registration, capturing position in typically less than
1µS. An additional input provides a hardware enable interlock. Two
digital outputs can be configured for functions such as motor brake
control and drive ready.
The MicroFlex e100 I/O is available to the NextMove e100 motion
controller as though the I/O is local to the NextMove. Limit errors, for
example, will call the Mint error handler on the NextMove e100. A
position latch on the MicroFlex e100 drive will result in the position
latch event being called within the Mint program on the NextMove
e100. This greatly simplifies system expansion.
Refer to catalog BR1202-I for full information on Baldor's real-time Ethernet Solution
technology. Incremental encoders (with or without Hall-effect tracks),
to utilize high performance feedback devices for optimum precision,
Refer to catalog BR1202-I for full information on Baldor's real-time Ethernet Solution
NextMove e100 multi-axis
motion controller for control of
up to 16 axes of MicroFlex e100
drives.
Ethernet
Specification: 100Mbit - IEEE802.3u compliant
Protocol : ETHERNET Powerlink V2 (EPL) and IP protocols TCP/UDP
Interface : Integrated 2 port Hub for daisy chain connection
Cable type : CAT5e Shielded cable, RJ45 connectors, Max 100m (330ft)
Address: 2 off rotary HEX switches sets node and IP address
Function : EPL /CiA DS402 Positioning Drive
CANopen
Single CAN port via standard 9 pin Sub-D connector. CANopen DS301: Manager of CANopen DS401 I/O
devices, Master functionality for peer-to-peer communications with other Mint nodes
CiA DS402 Positioning drive mode via CANopen (controlled device)
Protection
DC bus over voltage monitoring; DC bus under voltage monitoring; Peak over current; Motor short circuit; Over
temperature; I2t over current
Regenerative Capability
Regeneration braking IGBT - requires external regen resistor
Control Supply Input
24VDC nominal (20-30VDC) @ 1A external (4A power on surge) - customer supplied
Connectors
D-type for serial port and feedback. Two part terminals for motor and power
Indicators
1 off LED for drive status/health
2 off LEDs for Ethernet activity
2 off LEDs for CANopen activity
Dimensions
H: 180mm (7.09in) W: 79.6mm (3.13in) L: 157mm (6.18in)
Weight
1.5 Kg (3.3 lbs.)
Operating Temperature
0˚C to 45˚C
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com