Product Manual
Bainbridge Technologies warrants this product for a period of 24 months from the
date of purchase.
Bainbridge Technologies will repair or replace any defective product when directly
returned, postage paid, to us with a new or refurbished product.
This decision will be at Bainbridge Technologies discretion.
This warranty will be considered void if the product has suffered any obvious physical
damage or alteration either internally or externally. Bainbridge Technologies does not
cover damage arising from improper use, such as plugging the unit into unsuitable
power sources, or attempts to operate products with excessive power consumption
requirements, or use in unsuitable environments.
A minimum standard service fee of $35.00 plus G.S.T. will apply on all products. If the
product is deemed to be a warranty then this fee will be waived, and the product will
be replaced and/or repaired at no charge.
If there is no fault found with the product the service fee will apply, plus return freight
charges prior to the product being released.
If the product is out of warranty the service fee will be absorbed in the quote for repair.
If the quote for repair is denied then the service fee will apply plus freight before the
goods are released.
NOTE: This warranty is non transferable
NOTE: Reverse polarity & severe voltage surges are not covered by warranty.
Warranty:
PB-360
User Manual
MODEL PB-360P/N-24PB-360P/N-12 PB-360P/N-48
OUTPUT
BOOST CHARGE VOLTAGE
FLOAT CHARGE VOLTAGE
RECOMMENDED BATTERY
CAPACITY (AMP HOURS)
5
BATTERY TYPE
OUTPUT CURRENT (MAX)
INPUT
VOLTAGE RANGE
4
FREQUENCY RANGE
4
EFFICIENCY (TYP)
AC CURRENT (TYP)
INRUSH CURRENT (TYP)
POWER FACTOR (TYP)
LEAKAGE CURRENT
PROTECT
OVER TEMPERATURE
OVER VOLTAGE
REMOTE CONTROL
ENVIRONMENT
WORKING TEMP
WORKING HUMIDITY
STORAGE TEMP
TEMP. COEFFICIENT
VIBRATION
STORAGE HUMIDITY
SAFETY & EMC
4
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
HARMONIC CURRENT
EMI CONDUCTION &
RADIATION
EMS IMMUNITY
OTHERS
MTBF
DIMENSIONS
PACKING
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25
o
C of ambient
tempurature
2. The power supply is considered a component which will be installed into a dinal equiptment. The nal equiptment
must be re-conrmed that it still meets EMC directives
3. This is Bainbridge Technologies suggested range. Please consult your battery manufacturer for their suggestions
about maximum charging current limiation.
4. PB-600 unit can be operated with 90 ~ 264VAC of input voltage range and 47 ~ 63Hz of input frequency. Please
check the specication sheet for details.
NOTE
14.4V
13.6V
80 ~ 200Ah
Open & Sealed Lead Acid
25A
90~132VAC/180~264VAC selected by switch 248~370VDC
47 ~ 63Hz
85%
7A/115VAC 3.4A/230VAC
COLD START 60A
>0.65 (with P type) at 230VAC
<3.5mA / 240VAC
Protection type: Shut down o/p voltage
re-power on to recover
16 ~ 18V
Open: Normal work Short: Stop charging
-20 ~ +60
o
C (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-40 ~ +85
o
C
+
0.05%/
o
C (0 ~ 50
o
C)
10 ~ 500Hz, 2G 10min/1 cycle
60min each along X, Y, Z axes
10 ~ 95% RH
IEC60335-2-29 CB approved by TUV(except or 48V)
UL60950-1 approved
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M
Ohms / 500VDC / 25
o
C / 70% RH
Compliance to EN61000-3-2, -3 (only P type)
Compliance to EN55022 (CISPR22) Class B
Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11; ENV50204,
EN55024, light industry level, criteria A
115.8Khrs min. MIL-HDBK-217F (25
o
C)
253*135*48.5mm (L*W*H)
1.5Kg; 6pcs / 10Kg / 0.93CUFT
Protection type: Shut down o/p voltage, re-power on to
recover
_
28.8V
27.2V
40 ~ 125Ah
12.5A
86%
31 ~ 35V
57.6V
54.4V
20 ~ 65Ah
6.25A
87%
59 ~ 64V
SPECIFICATION PB-360
OVER TEMPERATURE Protection type: Automatically derate charge current until 0
VOLT ADJUSTABLE RANGE 13 ~ 14.7V 26 ~ 28.8V 26 ~ 58.6V
OVER LOAD
90 ~ 110% rated output current
Protection type: Constant current limiting, recovers
automatically after fault condition is removed
REVERSE POLARITY By internal fuse
PO Box 7222
Hemmant QLD 4174.
Phone: 1300 BAINTECH
Email: info@baintech.com.au
Website: www.baintech.com.au