Product Manual

材 质
/
版 权 所 有
时 间
版本号
HSX-RD-SC-
40
1
128g
75*105mm
40
40
量:240 00 mAh(8 8. 8Wh )
1 5V1 A
刷,
15 7
寸:75* 10 5mm
B. OPERATION GUIDANCE
Switch Instruction:
1.TEST:For checking battery storage level and unlock
the host. Press TESTkey to display the product quantity; press
3 mins to unlock.
2.Switch#12V/24V】: For choosing the jump start voltage.
a.PressSwitch:12V for 3 seconds, the 12Vindicator will lights
up and ready for jumping start 12V vehicle.
b.PressSwitch:24V for 3 seconds, the 24V indicator will lights
up and ready for jumping start 24V vehicle.
2
I. WARRANTY INFORMATION:
1.We offer a limited warranty for this product against any defects in material
and workmanship. The conditions of the warranty are as follows:
2.The warranty is only valid upon presentation of the original receipt (from
dealer/retailer) by the original purchaser with the product to be repaired or
replaced
3.The warranty is void if the serial number, date of purchase and label has
been removed
4.The warranty does not cover damage or product failure resulting from normal
wear and tear, physical abuse, improper installation, misuse, modification or
repairs by unauthorized third parties
5.We do not assume responsibility for any loss or damage incurred during
shipment or as a result of a force majeure
6.We are not liable for any incidental or consequential damages arising from
the use or misuse of this product
7.All warranty claims are limited to repair or replacement of the defective
product and at the sole discretion of us
8.If we repair or replace the product, the product will be covered for the
remaining time of the original warranty period. Repair or replacement may
involve the use of reconditioned units which are equivalent in function.
Replaced part or product becomes the property of us
9.Consumable components such as batteries are not covered by the warranty
8
Fuse Protection
Overcharg e an d
Overdischarge P rotection
Against-reverse Plug
Applied Standard GB/T 18287-2000
3
H. Warning:
1.Check the numbers of indicators is no less than 3 ones, if does,
Don’t attempt to jump start the vehicle.
2.Make sure the botton at Switch:12V orSwitch:24V
before connect the battery clamps to vehicle battery.
3.DO NOT connect to 12V vehicle battery, if 24V indication
lights up when press 24V button .
4.DO NOT connect to 24V vehicle battery, if 12V indication
lights up when press 12V button .
5.When 12V/24V Indication lights,DO NOT connect auto
battery positive and negative by mistake.Otherwise, it may
lead dangerous!
6.DO NOT connect the two clamps at the any time. Otherwise,
it may lead dangerous!
7.Remove the Jump Starter in 30s after the vehicle started
when 12V/24V Indication lights.
8.Always check if the jumper clamps are well connected, check
Always take care the appliance while using it.
Do not use by any child or infant
Do not use as a toy
Do not allow the appliance to become wet
Do not immerse the appliance in water
Do not operate the appliance in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust
Do not modify or disassemble the appliance Only a repair technician may
repair this unit
Do not expose the appliance to heat
Do not storage it in locations where the temperature may exceed 70 °C
Only Charge it at ambient temperatures between 0 °C and 40 °C
Only Charge it with the charger provided with the appliance.
Under extreme conditions, battery leakage may occur. Carefully wipe the
liquid off with cloth , and Please avoid skin contact when you notice liquid on
the battery. In case of skin or eye contact, rinse immediately with clean
water and seek medical attention
At the end of its useful life, discard the appliance with due care for our
Environment
6
!
!
!
!
5
G. TOXIC AND HARMFUL SUBSTANCES:
OIndi cate all homogeneous materials ' hazardous sub stances content a re below the MCV li mit specified
in the S tandard 2002/95/EC(RoHs).
Composition and amount of toxic and harmful substances in EPOWER
( ) Pb Hg Cd Cr Vi PBB PBDE
O O O O O O
C. PARTS LIST
4
D. TECHNICAL SPECIFICATIONS
12V/24V Intelligent Jump Starter User Manual
Thank you for choosing the Jump Starter! Always
follow basic safety precautions when using electrical
appliances. Read all instructions carefully, Please keep
this instruction manual for easy reference
A. PRODUCT LAYOUT
1
E. FAQ:
Q: How the jump starter identity that the car are the 12V or 24V?
A: Our jump starter can automatically identify in normal, but
when car battery are under low volt, we should press the switch
three seconds (attentaion to the corresponding volt) to start the
car.
Q: When the jump starter can not automatically identify the car
battery voltage when how to do?
A: Please request to help auto manufacturers or related
professionals.
Q. How many times can this appliance to jump start the
vehicle?
A. Normally it can jump start 12V vehicle approx. 30 times, can
jump start 24V vehicle approx. 20 times.
Q. How long does it need to fully charge the jump starter?
A. Approx. 8 hours through the 15V1A input.
Q. How about the lifetime of this appliance?
A. About 3 – 5 years.
Q. How long can this appliance still jump start the vehicle after
fully charged?
A. 6-12 months, however, we suggest you recharge it every 3
months.
S 0% 10% 20% 40% 60% 80% 100%
Indi cator Unli t 5 Flas hing 1 soli d 2 soli d 3 soli d 4 soli d 5 soli d
tora ge level
Storage Level Indicators
Press the switch to check the storage level of Jump Starter
The indicator will flash one by one during the period of charging.
Different numbers of solid indicators show different storage level
of Jump Starter. All indicators light off when the charging is
completed.
12V and 24V indicator:
a.12v or 24V indicator light on: mean the connected vehicle
battery is 12V or 24V, the circuit is open. It can jump start the
vehicle.
b.12V or 24V indicator flash: mean the connected vehicle battery
is12V or 24V, pls press the corresponding button for 3seconds.
When the indicator light on, then start the vehicle within 30
seconds.
c.12V and 24V indicators flash alternately: mean the product can
not identify the battery voltage automatically. People must judge
the vehicle battery voltage,then press correct corresponding
button
for 3seconds. When the indicator is light on, then start the vehicle
Within 30 seconds.
Charging for the Jump Starter itself
1. Plug the home adapter into the universal socket.
2. Connect 15V 1A input port of Jump Starter to the other end of
home adapter.
1.Make sure that the numbers of indicators is not less than 3 ones.
2.Connect the RED clamp to the vehicle's battery positive (+)
terminal and connect the BALCK clamp to the vehicle's
battery negative (-) terminal.
3. The jump starter will choose the 12V or 24V automatically,
and 12V or 24V indicator will be light on accordingly.
4.Start the vehicle.
5.When the vehicle is started, remove the jumper cable from
Jump Starter and disconnect RED and BALCK clamps from
the vehicle battery. Leave the vehicle's engine running.
Operation of 12V and 24V buttons:
Pls do not press the 12V or 24V botton in normal jump start , only
press it in the following abnormal situation.
1. When the jump starter connect to 24V truck, 24V indicator
flash, only press the 24V button for 3seconds ,then start the
truck within 30 seconds.
# Parts Name Quantity
1 Host 1
2 Home adapter 1
3 Car adapter 1
4 User Manual 1
Dimension235*225*80mm
Weight1660g
Output: 12V Jump Start; 24V Jump Start
Full charging time8 hours
Operating temperature: - 20~60/-4~140
Starting Current12V 500A; 24V 250A
Peak Current12V 1000A; 24V 500A
Input15V 1A
if the vehicle battery connector is rusted or dirty, clean it
before jumping start the vehicle. DO NOT jump start again
after 3 attempts. Otherwise, it will damage the host. And
Check your vehicle if it has other trouble.
9.DO NOT disassemble the host. Otherwise, it maybe
dangerous!
7
500AMP
INSTANT STANTING POWER
1000
PEAK BATTERY AMPS
Battery Clamps
Switch:24V
24V Indicator
12V Indicator
Switch:12V
Indicators
TEST
15V1A Input
Battery Capacity: 24000mAh(88.8Wh)
F. TROUBLE SHOOTING:
Low voltage protection of Jump
Starter is started.
Plug the adapter into the
1 5 V 1 A i n p u t p o r t t o
activate.
Finding Cause Remedies
No response when
pressing the [TEST]
switch button.
12V 24V indicators
are flashing at the
same time.
&
The appliance would be locked
up for self protection which
means the short circuit may
happen outside.
Unlock it with pushing
the [TEST]for 3 seconds
after the short circuit i s
removed.
12V/24V indication
twinkle frequently
when connect the
product to auto battery.
Red and Black Clamp reverse
connecting to the postive
and negative of auto battery.
Check if reverse,solve
it after correct
2. When the jump starter connect to 12V car, 12V indicator flash,
only press the 12V button for 3seconds ,then start the truck within
30 seconds.
3. 12V and 24V indicators flash alternately after connect to a
car,people must judge the car battery voltage is 12V or 24V,then
press correct corresponding button for 3seconds , then start the
car within 30 seconds.
4. When the car battery is completely power off or no testing, the
indicator is not flicker after correct connection with positive and
negative terminals, please press the corresponding button for
3seconds based on the car voltage ,then start the car within 30
seconds.
d.12V and 24V indicator lights flash at the same time: mean the
connection is mistake, should connect correctly,and then turn on
the engine.
Jump Start Vehicle Instruction:
4.07.12.0527

Summary of content (1 pages)