7 DEALER MANUAL FOR DP C220.CAN DEALER MANUAL FOR DISPLAY CONTENT 7.1 Important Notice 2 7.7.2 Selection of Support Levels 7.2 Introduction of Display 2 7.7.3 Selection mode 6 7.3 Product Description 3 7.7.4 Headlights / backlighting 7 7.3.1 Specifications 3 7.7.5 Walk Assistance 7 7.3.2 Functions Overview 3 7.7.6 SERVICE 8 7.4 Display Installation 4 7.5 Display 5 7.7.7 Battery capacity indication 7.8 Settings 7.6 Key Definition 5 7.8.1 "Display Setting" 7.
7.1 IMPORTANT NOTICE • If the error information from the display cannot be corrected according to the instructions, please contact your retailer. • Please use this product with care. • Do not use thinners or other solvents to clean the display. Such substances can damage the surfaces. • The product is designed to be waterproof. It is highly recommended to avoid submerging the display under water. • Warranty is not included due to wear and normal use and aging.
7.3 PRODUCT DESCRIPTION 7.3.
7.4 DISPLAY INSTALLATION 1. Remove the holding bracket from the display, and then place the display into position on the handlebar. (suitable for ∮22.2mm handlebar). 2. Then place the holding bracket on the underside of the display and tighten it into position with a M3.0*8 screw. Torque requirement: 1.0 N.m. 3. 4 Now connect the Display connector to the EB-Bus connector, ensuring both connectors are kept parallel when pushing firmly together.
7.5 DISPLAY 3 4 Display of battery capacity in real time. 2 Indicator of support level/walk assistance. 3 The display shows this symbol the lights are turned on. 4 Unit of speed 5 Digital speed display 6 Trip: Daily kilometers (TRIP) - Total kilometers (ODO) - Top speed (MAX) - Average speed (AVG) - Rremaining distance (RANGE) - Energy Consumption (CALORIES) - Output power (POWER)- Travel time (TIME). 5 2 6 , When Service: Please see the service section 7.
7.7 NORMAL OPERATION 7.7.1 Switching the System ON/OFF Press and hold off the system. (>2S) on the display to turn on the system. Press and hold (>2S) again to turn If the "automatic shutdown time" is set to 5 minutes (it can be reset with the "Auto Off" function, See "Auto Off"), the display will automatically be turned off within the desired time when it is not in operation.If the password function is enabled, you must enter the correct password to use the system. 7.7.
DEALER MANUAL FOR DISPLAY 7.7.4 Headlights / backlighting Hold the button (>2S) to activate the headlight and taillights. button (>2S) again to turn off the headlight. The brightness of the backlight can be set Hold the in the display settings "Brightness". 7.7.5 Walk Assistance The Walk assistance can only be activated with a standing pedelec. Activation: Press the button until this symbol appears.
7.7.6 SERVICE The display shows "SERVICE" as soon as a certain number of kilometers or battery charges has been reached. With a mileage of more than 5000 km (or 100 charge cycles), the “SERVICE" function is displayed on the display. Every 5000 km the display "SERVICE" is displayed every time. This function can be set in the display settings. 7.7.7 Battery capacity indicator The battery capacity is shown in the top left of the display.
7.8 SETTINGS Or highlight "EXIT" and press the button (<0.5S) to return to the main menu, or highlight "BACK" and press (<0.5S) the button (<0.5S) to return to the Settings interface. 7.8.1 "Display Setting" or button (<0.5S) and highlight Display Setting, and then briefly press the Press the (<0.5S) to access the following selections. button 7.8.1.1 "TRIP Reset" Reset mileage Press the or button (<0.5S) to highlight “Trip Reset” in the Display setting menu, and then press button (<0.5S) to select.
7.8.1.2 "Unit" Selections in km/Miles Press the or button (<0.5S) to highlight “Unit” in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between “Metric” (kilometer) or “Imperial” (Miles). Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the "Display setting". 7.8.1.3 "Brightness" Display brightness Press the or button (<0.5S) to highlight “Brightness” in the Display setting menu, and then press button (<0.
7.8.1.5 "Service" Switching the notification on and off 7.8.2 "Information" and buttons (at the same time) to enter Once the display is turned on, press and hold the into the setting menu, press the or button (<0.5S) to select “Information”, then press the button (<0.5S) to confirm and enter into "Information". 7.8.2.1 Wheel Size or button (<0.5S) to highlight “Wheel Size”, then press the button (<0.5S) to Press the confirm and view the wheel size. To return, press the button (<0.
7.8.2.2 Speed Limit or button (<0.5S) to highlight “Speed Limit”, then press the button (<0.5S) to Press the confirm and view the speed limit. To return, press the button (<0.5S) to exit back to the "Information". This information cannot be changed, this is only for information, about the pedelec. 7.8.2.3 Battery Information or button (<0.5S) to highlight “Battery Info”, then press the Press the confirm. Now press the or button (<0.5S) to view the contents. To return, press the button (<0.
Code definition Hardware ver unit Code Code definition unit Hardware version b10 Absolute SOC % Software ver Software version b11 Cycle times b01 Current temperature ℃ b12 Maximum not charging time Hour b04 Total voltage mV b13 Recently not charging time Hour b06 Average current mA d00 Number of battery cell b07 Remaining capacity mAh d01 Voltage of cell 1 mV b08 Full charge capacity mAh d02 Voltage of cell 2 mV b09 Relative SOC % dn Voltage of cell n mV NOT
7.8.2.5 Display Information or button (<0.5S) to highlight “Display Info”, then press the button (<0.5S) to Press the confirm. Now press the or button (<0.5S) to view Hardware Version or Software Version. To return, press the button (<0.5S) to exit back to the "Information". 7.8.2.6 Torque Information Press the or button (<0.5S) to highlight “Torque Info”, then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view Hardware Version or Software Version.
7.9 ERROR CODE DEFINITION Note: Please read carefully the description of the error code. When the error code appears, please first restart the system. If the problem is not eliminated, please contact your dealer or technical personnel. Error Declaration 04 The throttle has fault. 05 The throttle is not back in its correct position. Troubleshooting 1. Check the connector and cable of the throttle are not damaged and correctly connected. 2.
Error Declaration 13 Error with the temperature sensor inside of the battery 14 The protection temperature inside the controller has reached its maximum protection value 15 Error with the temperature sensor inside the controller Troubleshooting 1. Check all connectors from the battery are correctly connected to the motor. 2. If the problem still occurs, please change the Battery. 1. Allow the pedelec to cool down and restart the system. 2.
Declaration Troubleshooting 1. Check that all connections are connected correctly. 26 Speed signal of the torque sensor has an error 2. Please connect the pedelec to the BESST system to see if speed signal can be read by the BESST tool. 3. Change the Display to see if the problem is solved. 4. Using the BESST Tool update the controller to see if it resolves the problem, if not please change the torque sensor or contact your supplier.
Error Declaration Troubleshooting 37 WDT circuit is faulty Using the BESST tool update the controller to see if this resolves the problem. If not, please change the controller or contact your supplier. 41 Total voltage from the battery is too high Please change the battery. 42 Total voltage from the battery is too low Please Charge the battery. If the problem still occurs, please change the battery. 43 Total power from the battery cells is too high Please change the battery.
