Operator’s Manual WBMT26P WBMT26E 2-Cycle Multi-function Tool SAVE THESE INSTRUCTIONS SERVICE DO NOT RETURN THIS UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE. For assistance regarding the assembly, operation or maintenance of the unit, please call 1-844-786-7335 (in the United States) or contact email box CUSTOMERSERVICE@BADGERPOWERPRODUCTS.COM Warranty service is available through an authorized service center.
SAFETY SPARK ARRESTOR NOTE The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S.
SAFETY WARNINGS FOR GAS UNITS • • WARNING: Gasoline is highly flammable and its vapors can explode if ignited. Take the following precautions: • • • • • • • Store fuel only in containers specifically designed and approved for the storage of such materials. Always stop the engine and allow it to cool before filling the tank. Never remove the fuel tank cap or add fuel when the engine is hot. Always loosen the fuel tank cap slowly to relieve any pressure in the tank before fueling.
• SAFETY & INTERNATIONAL SYMBOLS • This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING SYMBOL • SAFETY ALERT SYMBOL MEANING • ON/OFF STOP CONTROL ON / START / RUN Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs.
KNOW YOUR UNIT APPLICATIONS As a trimmer /brush cutter: • Cutting grass and light weeds. • Edging • Decorative trimming around trees, fences, etc. Cutting Head Shaft Housing Coupler Cutting Head Shield Strap Hanger On/Off Switch Air Filter Cover Rear Handle Handle Throttle Lockout Throttle Control Fuel Cap Choke Lever Primer Bulb Starter Rope Grip Other optional attachments may be used with this unit.
SPECIFICATIONS* Model name WBMT26P/WBMT26E Cutting data brush cutter Engine type Air-Cooled, 2-Cycle Cutting circle diameter of blade 10 in. (255mm) Engine displacement 25.4cc (1.52 cu. in.) Cutter balde thickness 0.055 in. (1.4mm) Rated motor power 0.7kw Teeth quantity 3 Lubrication Fuel/Oil Mixture Cutting data hedge trimmer Fuel/Oil ratio 50:1 Cutting circle diameter 0.95 in. (24mm) Volumes of fuel tank 20 oz. (600ml) Bar length 16 in.
3.1 Fitting the guard for curved shaft grass deflector: -Remove the guard plug (1) from the end of the bottom part of the rod (2). -Secure the guard (3) to the support (4) using the supplied bolts (5) . 3.2 Fitting the guard for straight shaft grass deflector - Fix the transmission with hex key and wrench enclosed as standard accessories for tightening the nuts with the safe guard. -The guard is fixed to the angle transmission by two screws FIG 3.
c) Release the Nylon cutting head. Use screw driver to hold flange and then rotate the Nylon cutting head clockwise, it will be replaced. d) Fit the blade. Take the outer flange off after release the nut, then put the blade, outer flange, shield and nut according to priority as below picture. Note the blade rotation direction needs be same as below picture. Use screw driver to hold flange and tighten nut counter-clockwise, ensure the nut is tightened enough. e) Release blade.
Notes on tensioning the chain: The chain must be properly tensioned to ensure safe operation. When the saw chain can be raised by around 2 mm in the middle of the cutter bar, you know that the chain tension is ideal. During cutting, the temperature of the chain rises and its length changes. It is important therefore to check the chain tension at least every 10 minutes and to adjust it again as required. This applies in particular to new saw chains.
5. Fit the belt. According to picture showing, fit the belt well. OPERATION When operating this machine, please follow the instructions for operations steps. 1. Filling with fuel Danger of injury! Fuel is explosive! - Turn off and cool the motor down before filling the tank with fuel. - You must observe all safety instructions relating to handing fuel. Risk of device damage! The device is supplied without motor or gearbox oil. Before operating, you must fill it with fuel.
Before refuelling: Shake the fuel mixture container well. Place the machine on a flat stable surface, with the fuel tank cap facing upwards. Clean the fuel tank cap and the surrounding area to avoid any dirt from entering the tank during refilling. Carefully open the fuel tank cap to allow the pressure inside to decrease gradually. Use a funnel to refill and avoid filling the tank to the brim. – Unscrew the tank cap and remove it. – Pour in the fuel carefully, avoid spilling.
Start on the unit Do not start the unit until it has been completely assembled. Before switching on the unit, always check the oil. Check before use! Danger of injury! Do not operate the device unless you did not find any faults. If a part has become defective, make sure to replace it before you use the device again. Check the safe condition of the device: – Check the device for leaks. – Check the device for visual defects. – Check that all parts of the device have been securely fitted.
3. Pull the recoil starter handle 3-5 times to start the engine. Hold the machine firmly on the ground with one hand on the power unit, in order not to lose control of the machine during startup as following picture. 4. Pull the starter grip slowly for 10 - 15 cm until you feel some resistance, then tug it a few times until you hear the engine turn over. Then adjust the choke lever to (RUN) position. START UP RUN 5. Pull the starter grip again until the engine starts as normal.
6. When the engine is running and idling, the throttle lever on handle is as below picture. First press the lock off lever and then switch the throttle lever on, the machine will be working. 7. Adjusting line length when working: This machine is fitted with a “Tap & Go”head.To release more line, tap the cutting line head against the round with engine at top speed: the line will be released automatically and the knife cut off the excess length. 8.
11.WARNING! Do not use the machine for sweeping, tilting the cutting line head. The power of the engine could throw objects and small stones 15 metres or more, causing damage or injuries to people. Note: 1. Do not start the motor in tall grass 2. While mowing, lay the connection cable safely on footpaths and on areas which have already been mown. 3.
- The design of the petrol brush cutter allows for operation only at the right side of the user's body. - Keep the petrol brush cutter firmly with both hands on the handles. - Always make sure that the cutting tool continues to rotate briefly after the throttle has been released. - Always so that the cutting tool no longer turns in a proper engine idle not press down the throttle. - Always work with high speed so you have the best cutting results.
Working with pole saw Precautions for Saw procedure Never stand under the branch you want to saw. Use special caution when working with branches under tension and splintering wood. Possible risk of injury caused by falling branches and catapulting pieces of wood. In general, it is recommended to set the pruning saw at an angle of 60 ° to the road. Keep both hands well with the device during the cutting process and pay you up to an equilibrium position and a good level.
The most common effects are: - setback - recoil, - retreat Kickback The setback can occur when the moving saw chain meets at the upper quarter of the guide rail on a solid object or is pinched. The cutting force exerted on the chain from the saw, a rotational force in the opposite direction to the chain travel. This leads to an upward movement of the guide rail. Avoid kickback The best protection is to avoid situations that lead to setbacks. 1. Keep the position of the upper guide rail always in mind. 2.
Working with edger Holding the unit WARNING: Always wear eye, hearing, hand, foot and body protection to reduce the risk of injury when operating this unit Stand in the operating position. Hold the shaft grip with the right hand. Keep the right arm slightly bent. Hold the handle with the left hand. Keep the left arm straight. Hold the unit at waist level. Hold the unit so that it easily contacts the ground without the need for bending over.
ROUTINE MAINTENANCE Correct maintenance is essential to maintain the original efficiency and safety of the machine over time. Before performing any maintenance or cleaning work, always turn off the engine. 1. Do not spray the unit with water. Ingress of water may damage the engine and electrical connection. 2. Clean the unit with a cloth, hand brush, etc. WARNING! During maintenance operations: – Remove the spark plug cap. – Wait until the engine is sufficiently cold.
Change and clean the spark plug -Periodically remove and clean the spark plug using a metal brush to get rid of any deposits. -Check and reset the correct distance between the electrodes. -Replace the spark plug and fasten it firmly using the supplied wrench. -The spark plug must be replaced with one with the same characteristics whenever the electrodes have burnt or the insulation has worn, and in any case every 100 working hours.
SHARPENING THE LINE CUTTING KNIFE Remove the line cutting knife (1) from the guard (2) by unscrewing the screws (3). Fix the line cutting knife in a vice and sharpen it using a flat file, being careful to retain the original cutting angle. Refit the knife on the guard. 2 1 3 Care of the guide rail Turn the rail around every time you have the chain sharpened or replaced. This will avoid a one-sided wear of the rail, especially at the top and bottom.
The angle must also be maintained for all knives. For irregular angles, the chain is run irregularly, wear quickly and break down prematurely. Since these requirements can only be met with sufficient and regular exercise: - A File Holder must be used when sharpening the saw chain by hand. The correct filing angle marked on it. - Hold the file horizontally (at a right angle to the guide rail) and file according to the angle mark on the file holder. Support the file holder on the top plate and depth gauge.
TROUBLESHOOTING The table below contains a list of fault symptoms and explains what you can do to remedy the problem if your equipment fails to work properly. If the problem still persists after working through the list, please contact your nearest service workshop. Important hint in case of sending the equipment to a service station: Due to security reasons please see to it that the equipment is sent back free of oil and gas! Fault Possible cause Remedy Machine does not start.
NOTES 26
MANUFACTURER’S LIMITED WARRANTY The limited warranty set forth below is given by Badger with respect to new merchandise purchased and used in the United States, its possessions and territories . Badger warrants this product against defects in material and workmanship for a period of three (3) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship.
