Instruction Manual

Page 11
7-11
Installation & Operation Manual
SPECIFICATIONS
Sensor Assembly:
Housing: PEEK
Impeller: 316SS
Shaft: Tungsten Carbide
CS Specific: Torlon
®
Bearing, EDPM O-Rings
HS Specific: Ketron
®
Bearing, Aflas
®
O-Rings
Tee: Cast Bronze
ENVIRONMENTAL
Fluid Temp. -4°F to 140°F (-20°C to 60°C) - chilled
40°F to 260°F (4°C to 125°C) - hot
Ambient Temp. -4°F to 150°F (-20°C to 65°C)
Pressure Ratings:
Ba
d
gerDataIn
d
ustria
l
Series380BTUSystems
S
p
ecifications
MECHANICAL
SensorAssem
bl
y Mass <15
lb
Houseing:PEEK
Impe
ll
er:316SS ELECTRICAL
S
h
a
f
t:TungstonCar
b
i
d
e Inputs
CSSpeci
f
ic:Tor
l
onBearing,EDPMO‐Rings Power 12‐35VDC
HSSpeci
f
ic:KetronBearing,A
fl
asO‐Rings 9‐28VACrms
Communication Mo
db
us
Tee BACnet
CastBronze Output
Sca
l
e
d
Pu
l
se OpenDrain
TemperatureRatingForWette
d
Materia
l
s
CS:‐20Fto180F MATERIALS
HS:30Fto250F Housing Po
l
ycar
b
onate
F
l
owSensor PEEK
Am
b
ientTemperatureRating PottingMateria
l
Po
l
yuret
h
ane
‐20Cto65C Tee Brass
PressureRatings SensorBo
d
ySizes
TeeSizes 0.75
"
,1
"
,1.25
"
,1.5
"
,an
d
2
"
Recommen
d
e
d
DesignF
l
owRange
1to15FPS
380CS and 380HS*
Temp** F
Temp F PSIG Type Range COMMENTS
40 400 380CS -20 > +180 Torlon Brgs & EPDM seals
60 400 380CS -20 > +180 Torlon Brgs & EPDM seals
80 400 380CS -20 > +180 Torlon Brgs & EPDM seals
100 380 380CS -20 > +180 Torlon Brgs & EPDM seals
120 365 380CS -20 > +180 Torlon Brgs & EPDM seals
140 350 380CS -20 > +180 Torlon Brgs & EPDM seals
160 340 380CS -20 > +180 Torlon Brgs & EPDM seals
180 320 380CS -20 > +180 Upper Limit for Torlon & EPDM
200 300 380HS +30 > +250 Ketron Brgs & Aflas seals***
220 280 380HS +30 > +250 Ketron Brgs & Aflas seals
240 260 380HS +30 > +250 Ketron Brgs & Aflas seals
250 230 380HS +30 > +250 Ketron Brgs & Aflas seals
*Rating is based on PvT of Brass RTD fitting.
**Non-Freezing.
***Special: Ketron Brgs & EPDM seals for < +30F.
Accuracy
F
l
owCa
l
cu
l
ation:±1%o
f
Rate
TemperatureCa
l
cu
l
ation:±1%
BTUCa
l
cu
l
ation:±1%
OutputPu
l
seWi
d
t
h
10,50,150,200,or250mS
PutImageo
f
Dimentiona
l
Drawing
h
ere
380CS and 380HS*
Temp** F
Temp F PSIG Type Range COMMENTS
40 400 380CS -20 > +180 Torlon Brgs & EPDM seals
60 400 380CS -20 > +180 Torlon Brgs & EPDM seals
80 400 380CS -20 > +180 Torlon Brgs & EPDM seals
100 380 380CS -20 > +180 Torlon Brgs & EPDM seals
120 365 380CS -20 > +180 Torlon Brgs & EPDM seals
140 350 380CS -20 > +180 Torlon Brgs & EPDM seals
160 340 380CS -20 > +180 Torlon Brgs & EPDM seals
180 320 380CS -20 > +180 Upper Limit for Torlon & EPDM
200 300 380HS +30 > +250 Ketron Brgs & Aflas seals***
220 280 380HS +30 > +250 Ketron Brgs & Aflas seals
240 260 380HS +30 > +250 Ketron Brgs & Aflas seals
250 230 380HS +30 > +250 Ketron Brgs & Aflas seals
*Rating is based on PvT of Brass RTD fitting.
**Non-Freezing.
***Special: Ketron Brgs & EPDM seals for < +30F.
Figure 7: 380 CS & HS Pressure Ratings
MECHANICAL
Mass: Less than 13 lbs.
ELECTRICAL
Inputs
Power: Isolated 12-24 V DC/V AC ±10%
RS-485 is non-isolated to prevent ground faults. Do not share power with other devices.
Badger Meter A1028 plug-in type 120 VAC/12 V DC power supply recommended.
Communication: Modbus RTU
BACnet MSTP
Output
Scaled Pulse: Open Drain
0.01 Hz min. to 100 Hz max.
MATERIALS
Housing: Polycarbonate
Flow Sensor: PEEK
Potting Material: Polyurethane
Tee: Brass