R E AD Y S H E D 8X8 PEAK SHED MODEL: # 817220010 READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING CONSTRUCTION. Manufacturer: Backyard Discovery 3305 Airport Drive Pittsburg, KS 66762 1-800-856-4445 Save this assembly manual for future reference in the event that you need to order replacement parts.
STOP! DO NOT RETURN THIS PRODUCT TO STORE! If you have questions or concerns, please call 800-856-4445 or email customerserv@backyarddiscovery.com IMPORTANT! READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING. BEFORE YOU BEGIN • SAFETY FIRST Your safety is what matters, follow the instructions fully to ensure it gets dissassembled correctly and safely. • SURFACE PREPARATION To ensure proper disassembly you must uncrate your shed on a level firm surface.
DISASSEMBLY TOOLS REQUIRED • Drill • Phillips Bit Driver OTHER TOOLS WE SUGGEST • Utility Knife • 6' Ladder 2 • Gloves
PARTS BEING REMOVED (2) - SKID SLAT - W4L07803 1"x1 3/8"x45" (24x34x1143) DON'T SKIP ANY STEPS This crate has been designed to keep it's parts from being damaged and from falling over. Skipping steps could cause parts to fall and land on you or cause damage to your shed or surrounding structures. •These instructions will take you step by step through the disassembly process. •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) - 5/8" OSB FLOOR SHEATHING - W4L07664 5/8"x43"x92" •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) RS1 - ROOF SHEATHING - W4L07707 7/16"x14 5/8"x92" •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to. TOP VIEW CAUTION LOOSE PARTS BEHIND, MOVE WITH CAUTION.
PARTS BEING REMOVED (1) - 4 x 4 RUNNER - W4L07670 3 3/4"x3 3/4"x92" TREATED (1) RS1 - ROOF SHEATHING - W4L07707 7/16"x14 5/8"x92" •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) - DOOR DRIP BOARD - W4L07675 3/4"x1"x46 3/4" (20x24x1187) (2) - SHELF ASSEMBLY - W2A02133 (2) (2) M2 - TRIM - W4L07705 5/8"x3 3/8"x92" (16x86x2337) (4) N1 - CORNER TRIM - W4L07702 5/8"x2 3/8"x69 3/8" S1 - SOFFIT - W4L07706 1 1/2"x1 1/2"x92" (38x38x2337) (4) N2 - CORNER TRIM - W4L07704 5/8"x2 3/8"x69 1/2" (16x60x1765) •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) WP4 - UNIVERSAL LEFT CORNER PANEL - W2A02130 •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) WP5 - UNIVERSAL RIGHT CORNER PANEL - W2A02131 •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) - 4 x 4 RUNNER - W4L07670 3 3/4"x3 3/4"x92" TREATED •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) WP5 - UNIVERSAL RIGHT CORNER PANEL - W2A02131 (1) WP4 - UNIVERSAL LEFT CORNER PANEL - W2A02130 (2) - 2" CONCRETE BLOCK - CB000002 (1) - 4" CONCRETE BLOCK - CB000001 •Only remove item's shown in the current step, do not skip foward or take out any additional parts until instructed to. CAUTION TOP VIEW LOOSE PARTS BEHIND, MOVE WITH CAUTION. REMOVE REMOVE SCREW (2 PLS) NEXT REMOVE BLOCKS.
PARTS BEING REMOVED (1) - 5/8" OSB FLOOR SHEATHING - W4L07663 5/8"x48"x92" •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) - RIM JOIST - W4L07661 1 1/2"x3 1/2"x91 1/4" TREATED (3) R1 - RAFTER ASSEMBLY - W2A02132 •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) WP2 - REAR CENTER WALL PANEL - W2A02119 •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to.
PARTS BEING REMOVED (1) WP3 - FRONT CENTER WALL PANEL - W2A02120 •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to. TOP VIEW CAUTION LOOSE PARTS, MOVE WITH CAUTION.
PARTS BEING REMOVED (2) - LEVELING BLOCK - W4L07757 1"x5 1/2"x6" (2) - LEVELING BLOCK - W4L07756 1 1/2"x5 1/2"x6" (2) RS2 - ROOF SHEATHING - W4L07708 7/16"x37"x92" •Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to. TOP VIEW CAUTION REMOVING BOARD WILL REDUCE STABILTY.
PARTS BEING REMOVED (4) H1 - SHELF BRACE - W4L07709 15/16"x3 3/8"x14 3/16" (24x86x360) (4) (4) H2 - SHELF BRACE - W4L07710 15/16"x3 3/8"x5 1/2" (24x86x140) M1 - TRIM - W4L07703 5/8"x3 3/8"x53 7/8" (16x86x1369) SHINGLES CAUTION REMOVING BOARD WILL REDUCE STABILTY. TOP VIEW REMOVE REMOVE SCREW (4 PLS) REMOVE SCREW (4 PLS) REMOVE SHINGLES FROM BETWEEN THE TWO WALL PANELS BEFORE MOVING TO THE NEXT PAGE. NEXT REMOVE ALL LOOSE PARTS INCLUDING SHINGLES.
•Only remove screws shown in the current step, do not skip foward or take out any additional screws until instructed to. STOP LAY DOWN REMAINING PARTS BEFORE MOVING FOWARD. LA YO N FL AT SU AC RF E REMOVE 4 SCREWS ON BOTH SIDES. REMOVE 6 SCREWS ON BOTH SIDES.
PARTS BEING REMOVED (1) (7) - RIM JOIST - W4L07661 1 1/2"x3 1/2"x91 1/4" TREATED - FLOOR JOIST - W4L07662 1 1/2"x3 1/2"x89" TREATED (2) WP7 - SIDE WALL PANEL - W2A02129 (2) WP6 - SIDE WALL PANEL - W2A02128 NOTE: ONLY ONE WALL PANEL IS SHOWN. SO YOU WILL DO THESE STEPS 4 TIMES. REMOVE 4 SCREWS •NOW THAT THE CRATE IS FULLY DISSASEMBLED IT'S TIME TO START WITH THE ASSEMBLY. YOU CAN NOW FIND THE ASSEMBLY INSTRUCTION MANUAL AND GET STARTED.
READY SHED 8x8 PEAK SHED MODEL: # 817210011 READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING CONSTRUCTION. Manufacturer: Backyard Discovery 3305 Airport Drive Pittsburg, KS 66762 1-800-856-4445 Save this assembly manual for future reference in the event that you need to order replacement parts.
STOP! DO NOT RETURN THIS PRODUCT TO STORE! If you have questions or concerns, please call 800-856-4445 or email customerserv@backyarddiscovery.com IMPORTANT! READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING CONSTRUCTION. BEFORE YOU BEGIN • BUILDING RESTRICTIONS AND APPROVALS Be sure to check with local building department and homeowners association for specific restrictions and/or requirements before building.
Caring For Your Structure Wood Structures (Smart Panel) • To prevent leaking and premature aging of your shed, we recommend wood structures be thoroughly prepared before treatment. All joints between wall siding boards, window trim, door trim, corner boards, soffits, fascias, rake trim, vents, and naturally occurring hairline cracks in knots must be properly sealed with high quality caulking prior to treatment. We strongly recommend nail holes in all material types be filled prior to treatment.
ASSEMBLY TOOLS REQUIRED • Hammer • Drill with 3/8" Bit & Phillips Head Driver OTHER TOOLS WE SUGGEST • 6' Ladder • Tape Measure • 4' Level • Square • Gloves • Pencil 3 • 1/8" Allen Wrench • Safety Glasses
Basic Setup Dimensions Place the shed on level ground, not less than 3 ft [1 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 8'-2 3/16" 7'-9" 8'-1" 22.
Parts Identification Wood Components (NOT TO SCALE) - RIM JOIST - W4L07661 1 1/2"x3 1/2"x91 1/4" TREATED (2) (7) (2) - FLOOR JOIST - W4L07662 1 1/2"x3 1/2"x89" TREATED - 4 x 4 RUNNER - W4L07670 3 3/4"x3 3/4"x92" TREATED (1) - 5/8" OSB FLOOR SHEATHING - W4L07663 5/8"x48"x92" (1) - 5/8" OSB FLOOR SHEATHING - W4L07664 5/8"x43"x92" (4) N1 - CORNER TRIM - W4L07702 5/8"x2 3/8"x69 3/8" (4) N2 - CORNER TRIM - W4L07704 5/8"x2 3/8"x69 1/2" (16x60x1765) (4) M1 - TRIM - W4L07703 5/8"x3 3/8"x53 7/8" (16x8
Parts Identification Wood Components (NOT TO SCALE) (2) M2 - TRIM - W4L07705 5/8"x3 3/8"x92" (16x86x2337) (2) (1) S1 - SOFFIT - W4L07706 1 1/2"x1 1/2"x92" (38x38x2337) - DOOR DRIP BOARD - W4L07675 3/4"x1"x46 3/4" (20x24x1187) (2) RS1 - ROOF SHEATHING - W4L07707 7/16"x14 5/8"x92" (2) RS2 - ROOF SHEATHING - W4L07708 7/16"x37"x92" (4) H1 - SHELF BRACE - W4L07709 15/16"x3 3/8"x14 3/16" (24x86x360) (4) H2 - SHELF BRACE - W4L07710 15/16"x3 3/8"x5 1/2" (24x86x140) (2) SHELF ASSEMBLY - W2A02133 6
Parts Identification Wall Panels (2) WP7 - SIDE WALL PANEL - W2A02129 (1) WP2 - REAR CENTER WALL PANEL - W2A02119 (2) WP6 - SIDE WALL PANEL - W2A02128 (1) WP3 - FRONT CENTER WALL PANEL - W2A02120 7
Parts Identification Wall Panels (2) WP4 - UNIVERSAL LEFT CORNER PANEL - W2A02130 (2) WP5 - UNIVERSAL RIGHT CORNER PANEL - W2A02131 (3) R1 - RAFTER ASSEMBLY - W2A02132 8
Parts Identification Shingle Components (NOT TO SCALE) 1 (4) FULL - STARTER SHINGLE 7.125 x 36 (2) - STARTER SHINGLE 7.125 x 22.25 (30) FULL - ASPHALT SHINGLE 12 x 36 (8) 1 - ASPHALT SHINGLE 12 x 30 2 3 (10) 2 - ASPHALT SHINGLE 12 x 22.25 (8) 3 - ASPHALT SHINGLE 12 x 28.25 (1) - SHINGLE CAP 5 x 11.625 (1) - RIDGE CAP 9.25 (17) - RIDGE CAP 12 x 11.
Parts Identification Hardware (26) BQ - SCREW PFH 8x1 1/4 - H100087 (17) CY - SCREW PWH 8x5/8 - H100128 (94) BP - SCREW PFH 8x1 1/2 - H100086 (2) - 8x1 PFH SCREW BLK - WC - H100445 (17) BV - SCREW PFH 8x2 1/4 - H100091 (9) VT - SCREW PFH 8x1-1/2 BLK - H100200 (9) BW - SCREW PFH 8x3 - H100092 (100) - SCREW T-25 9x2 - H100579 (4) - SCREW PFH 8x2 BLK - H100391 (72) - SCREW T-25 9x3 - H100578 (274) - 7/8" ROOFING NAIL GALV.
Parts Identification Accessories (NOT TO SCALE) (1) G K IN C O -L OR DO ND HA LE 06 M0 4 A 03 (2) G IN PR S - H TC LA A (2) - VENT (8x16) - A4M00771 (1) MX - BYD ID TAG (MEDIUM) WITHOUT AGES - A100240 11 L MB E SS Y 0 M0 4 -A 4 77
FLOOR FRAME (2) - RIM JOIST - W4L07661 1 1/2"x3 1/2"x91 1/4" TREATED (7) - FLOOR JOIST - W4L07662 1 1/2"x3 1/2"x89" TREATED (2) - 4 x 4 RUNNER - W4L07670 3 3/4"x3 3/4"x92" TREATED (32) - SCREW T-25 9x3 - H100578 • IMPORTANT: On a level surface, make sure the floor frame is square before moving on to next step. It is critical that the 4x4 Runners be touching solid ground everywhere during this step. Being level is not yet a priority as we will level the structure after we get the floor assembled.
FLOOR SHEATHING (72) - SCREW T-25 9x2 - H100579 (1) - 5/8" OSB FLOOR SHEATHING - W4L07663 5/8"x48"x92" - 5/8" OSB FLOOR SHEATHING - W4L07664 5/8"x43"x92" (1) • Bring sheathing to square before securing with 2" star drive fasteners. ALL SCREWS LAND IN JOISTS BELOW. 5/8" OSB FLOOR SHEATHING PLACE SMOOTH SIDE UP. FLOOR JOIST DO O R 1/4 1/2 43.00 START AT THE FRONT OF THE SHED AND WORK TOWARDS THE REAR. 48.00 NOTE ALL SCREWS SHOULD BE CENTER ON JOISTS BELOW. 3/4 DOOR 92.
FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. INCLUDED LEVELING MATERIALS •2 pcs - 2x6x6 Treated Wood Block •2 pcs - 5/4x6x6 Treated Wood Block •1 pcs - 4x8x16 Concrete Block •2 pcs - 2x8x16 Concrete Block •4 pcs - 7.5x12 Asphalt Shingles (Can be cut in half if needed) • Start by locating the most level ground in your preferred shed locations. This area must be a stable, solid, and dry location.
LEFT FRONT WALL INSTALLATION (2) - SCREW T-25 9x3 - H100578 (1) WP6 - SIDE WALL PANEL - W2A02128 SCREW T-25 9x3 (2 PLS) WP6 NOTE: MAKE SURE SCREWS EITHER GO INTO RIM JOISTS OR FLOOR JOISTS FOR ADDED STRENGTH WHEN MOUNTING WALLS. DO O R IMPORTANT: Make sure to mate the wall panel siding with joists. DO NOT LEAVE ANY GAP BETWEEN THE PANEL SIDING AND ANY OF THE FLOOR JOIST.
LEFT REAR WALL INSTALLATION (5) - SCREW T-25 9x3 - H100578 (1) WP7 - SIDE WALL PANEL - W2A02129 NOTE: MAKE SURE SCREWS EITHER GO INTO RIM JOISTS OR FLOOR JOISTS WHEN MOUNTING WALLS. NOTE SMART SIDING JOINT. SIDE VIEW WP7 SCREW T-25 9x3 (5 PLS) IMPORTANT: Make sure to mate the wall panel siding with joists. DO NOT LEAVE ANY GAP BETWEEN THE PANEL SIDING AND ANY OF THE FLOOR JOIST.
FRONT LEFT WALL INSTALLATION (4) - SCREW T-25 9x3 - H100578 (1) WP4 - UNIVERSAL LEFT CORNER PANEL - W2A02130 WP4 TOP VIEW DOOR SCREW T-25 9x3 (4 PLS) NOTE HOW PANEL MATES WITH EXISTING PANELS WITH NO GAP. IMPORTANT: Make sure to mate the wall panel siding with joists. DO NOT LEAVE ANY GAP BETWEEN THE PANEL SIDING AND ANY OF THE FLOOR JOIST.
FRONT CENTER WALL INSTALLATION (3) V - BOLT WH 5/16x5 - H100022 (4) BG - T-NUT 5/16 - H100074 (1) R - BOLT WH 5/16x3 1/2 - H100018 (4) AC - WASHER LOCK EXT 8x19 - H100030 (1) WP3 - FRONT CENTER WALL PANEL - W2A02120 (4) - SCREW PFH 8x2 BLK - H100391 BOLT WH 5/16x3 1/2 (1 PLS) WP3 USE HAMMER TO TAP IN T-NUTS WASHER LOCK EXT 8x19 (4 PLS) BOLT WH 5/16x5 (3 PLS) T-NUT 5/16 (4 PLS) SCREW PFH 8x2 BLK (4 PLS) 18
FRONT RIGHT WALL INSTALLATION (1) - SCREW T-25 9x3 - H100578 (4) AC - WASHER LOCK EXT 8x19 - H100030 (1) WP5 - UNIVERSAL RIGHT WALL PANEL - W2A02131 (4) BG - T-NUT 5/16 - H100074 (1) R - BOLT WH 5/16x3 1/2 - H100018 (3) V - BOLT WH 5/16x5 - H100022 IMPORTANT: Make sure to mate the wall panel siding with joists. DO NOT LEAVE ANY GAP BETWEEN THE PANEL SIDING AND ANY OF THE FLOOR JOIST.
RIGHT FRONT WALL INSTALLATION (5) - SCREW T-25 9x3 - H100578 (1) WP7 - SIDE WALL PANEL - W2A02129 IMPORTANT: Make sure to mate the wall panel siding with joists. DO NOT LEAVE ANY GAP BETWEEN THE PANEL SIDING AND ANY OF THE FLOOR JOIST. WP7 SCREW T-25 9x3 (5 PLS) NOTE: MAKE SURE SCREWS EITHER GO INTO RIM JOISTS OR FLOOR JOISTS BELOW FOR ADDED STRENGTH WHEN MOUNTING WALLS. MAKE SURE THE WALL PANEL IS FLUSH AND AGAINST THE RIM JOIST WITH NO GAPS.
RIGHT REAR WALL INSTALLATION (5) - SCREW T-25 9x3 - H100578 (1) WP6 - SIDE WALL PANEL - W2A02128 • IMPORTANT: Make sure to mate the wall panel siding with joists. DO NOT LEAVE ANY GAP BETWEEN THE PANEL SIDING AND ANY OF THE FLOOR JOIST. SCREW T-25 9x3 (5 PLS) WP6 NOTE BEFORE MOVING ON REMOVE SAFTY BOARD. AT THIS TIME OPEN AND CLOSE DOORS TO ENSURE PROPER FUNCTION BEFORE MOVING ON. NOTE: MAKE SURE SCREWS EITHER GO INTO RIM JOISTS OR FLOOR JOISTS FOR ADDED STRENGTH WHEN MOUNTING WALLS.
REAR RIGHT WALL INSTALLATION (4) - SCREW T-25 9x3 - H100578 (1) WP5 - UNIVERSAL RIGHT CORNER PANEL - W2A02131 •IMPORTANT: Make sure to mate the wall panel siding with joists. DO NOT LEAVE ANY GAP BETWEEN THE PANEL SIDING AND ANY OF THE FLOOR JOIST.
REAR CENTER WALL INSTALLATION (4) BG - T-NUT 5/16 - H100074 (4) R - BOLT WH 5/16x3 1/2 - H100018 (4) AC - WASHER LOCK EXT 8x19 - H100030 (1) WP2 - REAR CENTER WALL PANEL - W2A02119 •IMPORTANT: Make sure to mate the wall panel siding with joists. DO NOT LEAVE ANY GAP BETWEEN THE PANEL SIDING AND ANY OF THE FLOOR JOIST.
REAR LEFT WALL INSTALLATION (4) R - BOLT WH 5/16x3 1/2 - H100018 (4) - SCREW T-25 9x3 - H100578 (4) BG - T-NUT 5/16 - H100074 (1) WP4 - UNIVERSAL LEFT CORNER PANEL - W2A02130 (4) AC - WASHER LOCK EXT 8x19 - H100030 USE HAMMER TO TAP IN T-NUTS • IMPORTANT: Make sure to mate the wall panel siding with the outside floor joists. DO NOT LEAVE ANY GAP BETWEEN THE PANEL SIDING AND THE FLOOR JOIST.
WALL PANEL FASTENERS (22) - SCREW T-25 9x2 - H100579 -OPTIONALFor your convenience we recommend that the painting be done at this time. See "PAINT" on page 2 of this manual. SCREW T-25 9x2 (6 PLS) SCREW T-25 9x2 (6 PLS) SCREW T-25 9x2 (6 PLS) SCREW T-25 9x2 (4 PLS) .75 REAR VIEW PLACE SCREWS CENTER OF EVERY OTHER PROFILE IN SMART SIDING.
RAFTER INSTALLATION (3) R1 - RAFTER ASSEMBLY - W2A02132 (6) - SCREW T-25 9x3 - H100578 21 3/8 20 9/16 PLACE RAFTERS OVER VERTICLE WALL STUDS. RAFTERS SHOULD OVERHANG 1.5" ON EACH SIDE AS SHOWN BELOW. 20 9/16 1.
CORNER TRIM INSTALLATION (4) N1 - CORNER TRIM - W4L07702 5/8"x2 3/8"x69 3/8" (24) BP - SCREW PFH 8x1 1/2 - H100086 (4) FIRST: INSTALL N2 FLUSH TO FRONT WALL PANEL AND FLUSH TO BOTTOM OF SIDING.. N2 - CORNER TRIM - W4L07704 5/8"x2 3/8"x69 1/2" (16x60x1765) TOP VIEW N2 DOOR SECOND: INSTALL N1 FLUSH WITH N2 AND FLUSH WITH THE BOTTOM OF THE SIDING. N1 SCREW PFH 8x1 1/2 (24 PCS) N2 N1 FRONT VIEW N1 N2 N2 N1 27 ATTENTION: TRIM MUST BE FLUSH WITH SIDING.
SIDE TRIM BOARDS (2) M2 - TRIM - W4L07705 5/8"x3 3/8"x92" (16x86x2337) (8) BW - SCREW PFH 8x3 - H100092 (2) S1 - SOFFIT - W4L07706 1 1/2"x1 1/2"x92" (38x38x2337) REST S1 UNDER RAFTERS AND ON TOP OF THE N2 SIDE TRIM BOARDS. ALLIGN S1 & M2 PILOT HOLES AND MOUNT WITH SCREWS. S1 M2 SCREW PFH 8x3 (8 PLS) 2 1/8 NOTE ORIENTATION OF M2 NOTE SCREWS PASS THROUGH BOTH PILOT HOLES IN BOTH BOARDS (S1 & M2).
FRONT AND REAR TRIM BOARDS (4) M1 - TRIM - W4L07703 5/8"x3 3/8"x53 7/8" (16x86x1369) (12) BP - SCREW PFH 8x1 1/2 - H100086 • ASSEMBLE TRIM BOARDS TO BE CENTER TO PEAK AND HAVE 7/16" OFFSET FROM RAFTERS AND SIDING. NOTE: M1'S SIT ON N1'S TO GET DESIRED HEIGHT; IF NEEDED ADJUST N1 BOARDS UP OR DOWN TO GET REQUIRED 7/16" GAP ON M1 TRIM AS SHOWN BELOW. M1 SCREW PFH 8x1 1/2 (12 PLCS) M1 RESTS ON THE CORNER TRIM TO SET HEIGHT.
ROOF SHEATHING INSTALLATION (2) RS1 - ROOF SHEATHING - W4L07707 7/16"x14 5/8"x92" (50) BP - SCREW PFH 8x1 1/2 - H100086 (2) RS2 - ROOF SHEATHING - W4L07708 7/16"x37"x92" NOTE: PLACE SHEATHING ROUGH SIDE UP. RAFTER SPACING. TOP VIEW PREFERRED ASSEMBLY METHOD: PLACE RS2's ON FIRST, USING A TAPE MEASURE ADJUST RAFTERS AS NEEDED TO GET SPACING AS SHOWN. THIS STEP IS NEEDED TO SQUARE RAFTERS, ONCE RAFTERS ARE SQUARE AND STRAIGHT SCREW DOWN RS2's TO HOLD RAFTERS IN PLACE.
EXTERIOR COMPONETS (1) (12) CY - SCREW PWH 8x5/8 - H100128 - DOOR DRIP BOARD - W4L07675 3/4"x1"x46 3/4" (20x24x1187) (4) BP - SCREW PFH 8x1 1/2 - H100086 (2) - VENT (8x16) - A4M00771 (1) MX - BYD ID TAG (MEDIUM) WITHOUT AGES - A100240 SIDE VIEW • The vent (8x16) is installed over the 4-1/2" holes in the front and rear center panels. Vent alignment should be centered horizontally and touching the trim above it vertically.
(2) FULL - STARTER SHINGLE 7.125 x 36 (11) - 7/8" ROOFING NAIL GALV. - H100446 (1) - STARTER SHINGLE 7.125 x 22.25 STARTER SHINGLES USE THESE STEPS FOR BOTH SIDES • WORK LEFT TO RIGHT WHEN INSTALLING STARTER SHINGLES. LEFT SIDE RIGHT SIDE START HERE FULL STARTE R FULL STARTE R 22.25" STAR TE R 7/8" ROOFING NAIL GALV. (12 PLCS) RIGHT SIDE LEFT SIDE TOP VIEW LEFT SIDE 1/2" OVERHANG ON ALL SIDES OF SHED.
1 (1) FULL - ASPHALT SHINGLE 12 x 36 (1) 1 - ASPHALT SHINGLE 12 x 30 • Familiarize yourself with a 3-Tab Shingle. SHINGLE NAIL PATTERN Notch Notch Tar / Sealing Strip (8) - 7/8" ROOFING NAIL GALV. - H100446 NAIL ON TOP EDGE OF SEAL STRIP. 1" 1" Half Rain Slot 5 1/4 6 3/4 TO NAILS Full Rain Slot SHINGLE COURSE - START PRE-CUTT SHINGLES WILL HAVE A NUMBER STAMPED ON THE SHINGLE. ARRANGE THESE SHINGLES AS SHOWN TO GET DESIRED RESULTS.
2 (5) 2 - ASPHALT SHINGLE 12 x 22.25 (13) FULL - ASPHALT SHINGLE 12 x 36 3 1 (3) 1 - ASPHALT SHINGLE 12 x 30 (95) - 7/8" ROOFING NAIL GALV. - H100446 (4) 3 - ASPHALT SHINGLE 12 x 28.25 FINISH SHINGLE COURSES • CONTINUE PLACING SHINGLES AS SHOWN USING THE NUMBERS ON THEM TO DETERMINE PLACEMENT. RIGHT SIDE LEFT SIDE FULL SHINGLES 3 1 FULL 2 1 FULL •REPEAT COURSES 1 & 2 ALL THE WAY UP THE SHED UNTIL YOU REACH THE PEAK AS SHOWN BELOW.
(38) - 7/8" ROOFING NAIL GALV. - H100446 (1) - RIDGE CAP 9.25 (17) - RIDGE CAP 12 x 11.875 (1) - SHINGLE CAP 5 x 11.625 RIDGE CAP INSTALLATION • IF NEEDED BEND EXCESS SHINGLES OVER PEAK BEFORE STARTING ON RIDGE CAPS. • INSTALL FIRST RIDGE CAP FLUSH WITH SHINGLES BELOW AS SHOWN. START AT THE FRONT OF YOUR SHED AND WORK TOWARDS THE REAR. 7/8" ROOFING NAIL GALV. (2 PLCS) RIDGE CAP 12 x 11.875 (1 PLCS) FRONT OF SHED. TOP VIEW WEATHER SEAL ONE NAIL PER SIDE ABOVE WEATHER SEAL.
RIDGE CAP INSTALLATION • Install second ridge cap 5" back as shown. Repeat this process until you reach the end of the shed. 7/8" ROOFING NAIL GALV. (2 PLCS) 5 RIDGE CAP 12 x 11.875 (1 PLCS) FRONT OF SHED. NOTE: NAILS ARE COVERED BY NEW RIDGE CAPS. REPEAT THIS STEP (15 TIMES) • Install last ridge cap 5" back as shown, it should be flush with the back of your shed. TOP VIEW 7/8" ROOFING NAIL GALV. (2 PLCS) RIDGE CAP 9.25 (1 PLCS) FRONT OF SHED.
DOOR COMPONENTS (2) - 8x1 PFH SCREW BLK - WC - H100445 (2) - SPRING LATCH ASSEMBLY - A4M00774 (8) VT - SCREW PFH 8x1-1/2 BLK - H100200 (1) - LOCKING DOOR HANDLE - A4M00603 PREFERRED HANDLE INSTALLATION SPRING LATCH INSTALLATION • Insert the handle into the hole from the outside with the • The spring latches should attach to the door stop on the inside of the left door as you look at the door from the outside. Holes need to be drilled into the floor and header to make them functional.
OPTIONAL - SHELF CONFIGURATION (4) H1 - SHELF BRACE - W4L07709 15/16"x3 3/8"x14 3/16" (24x86x360) (4) (8) BQ - SCREW PFH 8x1 1/4 - H100087 H2 - SHELF BRACE - W4L07710 15/16"x3 3/8"x5 1/2" (24x86x140) (16) BV - SCREW PFH 8x2 1/4 - H100091 (2) SHELF ASSEMBLY - W2A02133 13 11 14 12 15 13 PREFERRED ASSEMBLY METHOD: 11 9 12 10 STEP 1 DESIDE WHERE YOU WANT THE SHELVES TO GO. IN OUR EXAMPLE YOU CAN SEE WHEN WERE DONE THE SHELVES WILL BE AT 20" AND 40" AFTER THEIR ASSEMBLED.
OPTIONAL - LOFT CONFIGURATION (24) BQ - SCREW PFH 8x1 1/4 - H100087 H1 - SHELF BRACE - W4L07709 (4) 15/16"x3 3/8"x14 3/16" (24x86x360) (8) BV - SCREW PFH 8x2 1/4 - H100091 (2) SHELF ASSEMBLY - W2A02133 • Lay one shelf down and mount H1 boards as shown. SCREW PFH 8x1 1/4 (12 PLS) H1 H1 23.
Post Installation FAQs Shingles Aren’t Laying Flat This is a normal condition. Please allow a minimum of (2) full weeks of temperatures above 60º F for shingles to seal. Subfloor Sheathing Small gaps between subfloor sheathing sheets are a normal aspect of construction. You may caulk gaps to fill and seal them if you wish. Floors may also be painted for additional protection and appearance. Consult with a professional paint and caulk supplier for recommendations.
Backyard Discovery Sheds 15 Year Limited Warranty This Limited Warranty by Backyard Discovery applies to Products manufactured under the Backyard Discovery brand. Backyard Discovery warrants this product is free from defects in material and workmanship for a period of fifteen (15) years from the original date of purchase. This fifteen (15) year warranty covers all parts including wood, hardware, and accessories. All wood carries a fifteen (15) year pro-rated warranty against rot and decay.
