Tucson Wooden Swing Set Model: #65411 • Owner's Manual • Frequently Asked Questions • Assembly Instructions • Warranty Information Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetsonline.com (you will also find any updates on assembly instructions and information to order replacement parts) Features the fastening system.
STOP PARE Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com ¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA! La tienda donde realizó la compra no almacena piezas de este producto.
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing material washing away during heavy rains. 3.
Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth 6" (152mm) 9" (228mm) 12" (304mm) to 9" (228mm) Wood Chips 7' (2.13m) 10' (3.05m) 11' (3.35m) 10' (3.05m) Double-Shredded bark mulch 6' (1.83m) 10' (3.05m) 11' (3.35m) 7' (2.13m) Engineered Wood Fibers 6' (1.83m) 7' (2.13m) >12' (3.66m) 6' (1.83m) Fine Sand 5' (1.52m) 5' (1.
Owner’s Manual Play Set 18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that they cannot be looped back on it. 19. Instruct children not to attach items to the playground equipment that are not specifically designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and chain as they may cause a strangulation hazard. 20. Instruct children to never wrap their legs around swing chain. 21.
Owner’s Manual Play Set Additional Maintenance: • Check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. • Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear. Light sand may be necessary to maintain a safe playing environment.
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY 9 HANDBOOK X3.
Play Set Assembly Manual FAQs: 1. Does the area for the playset need to be level? Yes. Backyard Discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3.
Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.
Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 7'-3 3/4" [2.2 m] 19'-3 3/4" [5.9 m] 17'-7 3/8" [5.4 m] 6' [1.8 m] Safe Play Zone Important Assembly Notes: 6'-1 1/8" [1.9 m] Your set has been designed and engineered for children only and for residential use only. A maximum of 150 lbs.
Parts Identification Wood Components (NOT TO SCALE) E1 - FORT UPRIGHT - W101519 1 3/8"x3 3/8"x89 1/2" (36x86x2273) (2) E2 - FORT UPRIGHT - W101520 1 3/8"x3 3/8"x89 1/2" (36x86x2273) (2) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (2) (2) F1 - ANGLE BRACE - W101630 1 3/8"x2 3/8"x18 1/8" (36x60x460) (2) F2 - ANGLE BRACE - W101629 1 3/8"x2 3/8"x12 1/4" (36x60x310) G1 - GROUND BOARD - W101529 1"x5 1/4"x59 1/2" (24x134x1511) (2) G2 - SWING BEAM SUPPORT - W101623 1"x5 1/4"x34 1/8"
Parts Identification Wood Components (NOT TO SCALE) (2) H5 - PICNIC TARP SUPPORT - W101542 1"x3 3/8"x24 1/2" (24x86x622) (2) (2) H6 - WALL SLAT - W101535 1"x3 3/8"x25 1/2" (24x86x648) H7 - PICNIC SUPPORT - W101625 1"x3 3/8"x15 1/4" (24x86x387) (2) H8 - PICNIC SUPPORT - W101628 1"x3 3/8"x13 1/2" (24x86x344) (2) H9 - PICNIC SUPPORT - W101626 1"x3 3/8"x6 3/4" (24x86x172) (4) H10 - FLOOR BRACE - W101534 1"x3 3/8"x3 3/8" (24x86x86) (2) H73 - ROCK WALL RAIL - W100024 1"x3 3/8"x48 3/4" (24x86x1238)
Parts Identification Wood Components (NOT TO SCALE) (1) K2 - ARCHED WALL RAIL - W101531 5/8"x5 1/4"x34 7/8" (16x134x887) (1) K3 - ARCHED WALL RAIL - W101530 5/8"x5 1/4"x34 1/8" (16x134x868) (2) (1) K4 - WALL RAIL - W101533 5/8"x5 1/4"x34 1/8" (16x134x868) (2) M1 - TARP SUPPORT - W101540 5/8"x3 3/8"x40" (16x86x1016) (13) M2 - FLOOR BOARD - W101525 5/8"x3 3/8"x36 3/4" (16x86x935) (3) M3 - TARP SUPPORT - W101539 5/8"x3 3/8"x36 3/4" (16x86x935) M4 - FLOOR/TARP SUPPORT - W101541 5/8"x3 3/8"x34 7/8"
Parts Identification Wood Components (NOT TO SCALE) (1) M9 - PICNIC CLEAT - W101633 5/8"x3 3/8"x6 3/4" (16x86x172) (2) M10 - WALL RAIL - W101621 5/8"x3 3/8"x6 1/4" (16x86x160) (2) M11 - WALL RAIL - W101527 5/8"x3 3/8"x4 3/4" (16x86x122) (9) M12 - WALL SLAT - W101536 5/8"x3 3/8"x25 1/4" (16x86x640) (1) M13 - WALL RAIL - W4L05295 5/8"x3 3/8"x34 7/8" (16x86x887) (6) (2) (1) (2) M71 - ROCK BOARD - W100022 5/8"x3 3/8"x20 1/4" (16x86x514) M72 - ROCK WALL SLAT - W100023 5/8"x3 3/8"x20 1/4" (16x86x5
Parts Identification Hardware (42) Z - LAG SCREW WH 5/16x2 - H100027 (56) D - NUT BARREL WH 5/16x7/8 - H100005 (2) AA - LAG SCREW WH 5/16x2 1/2 - H100028 (7) CM - BOLT WH 5/16x1/2 - H100115 (13) BG - T-NUT 5/16 - H100074 (7) BF - T-NUT 3/8 - H100073 (4) F - BOLT WH 5/16x1 - H100008 (7) A - BOLT FA 3/8x1 1/2 - H100001 (19) H - BOLT WH 5/16x1 1/2 - H100010 (60) AD - WASHER LOCK EXT 12x19 - H100031 (19) CY - SCREW PWH 8x5/8 - H100128 (6) J - BOLT WH 5/16x1 3/4 - H100011 (99) AC - WASHER LOCK EXT 8x19
Parts Identification Hardware (9) BL - SCREW TAPPING 14x3/4 - H100083 (4) CG - WASHER LOCK INT 8x15 - H100108 (4) AZ - BOLT PTH 1/4x1 1/4 - H100062 (48) BR - SCREW PFH 8x1 1/8 - H100088 (48) BQ - SCREW PFH 8x1 1/4 - H100087 (44) BP - SCREW PFH 8x1 1/2 - H100086 (9) BS - SCREW PFH 8x1 3/4 - H100089 (6) BZ - SWING HANGER QUICK LINK - H100099 (4) CE - WASHER FLAT 9x18 - H100106 (4) BX - WASHER SPLIT 5/16 - H100095 (15) CD - WASHER FLAT 8x27 - H100105 (82) CK - SCREW PFH 8x2 - H100111 (4) BT - SCRE
Parts Identification Accessories (NOT TO SCALE) (2) EA - HAND GRIP YELLOW PLASTIC - A100043 (1) EK - SLIDE RAIL 8' GREEN RIGHT - A100054 (1) EL - SLIDE RAIL 8' GREEN LEFT - A100055 (1) HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 (1) EM - SLIDE BED 8' YELLOW - A100056 (6) ER - CLIMBING ROCK GREEN SMALL -A100060 (1) SR - "B" REVISION TAG - A100315 (2) QZ - TRIANGLE PLATE 100° 5 HOLE - A100294 (1) - TRAPEZE - A6P00034 (2) FB - SWING SEAT YELLOW - A100070 (2) GD - L BRACKET 66x66x127 -A100140 (4)
Parts Identification Accessories (NOT TO SCALE) (1) KB - PICNIC TABLE TARP - A100195 (6) KD - PLASTIC GROUND STAKE BROWN - A100179 2 -T -40 B RX O T IT 00 10 A - 42 2 - T-40 TORX WRENCH - A100041 (1) KC - ROOF TARP - A100196
(1) M77 - SLIDE BRACE - W100544 5/8"x3 3/8"x17 1/4" (16x86x438) (1) EM - SLIDE BED 8' YELLOW - A100056 SLIDE ASSEMBLY STEP 1 (3) T-NUT 5/16 (3) BOLT WH 5/16x1/2 SLIDE BED 8' YELLOW (1 PLC) BOLT WH 5/16x1/2 (3 PLCS) T-NUT 5/16 (3 PLCS) M77 USE 'M77' SLIDE BRACE AS A TEMPLATE FOR DRILLING BOTTOM HOLE PATTERN IN SLIDE BED. BE SURE TO PLACE SLIDE BRACE UP 1/4" FROM BOTTOM EDGE OF SLIDE BED BEFORE MARKING HOLE PATTERN. TIP: PREBENDING THE ENDS WILL EASE ASSEMBLY.
(1) EL - SLIDE RAIL 8' GREEN LEFT - A100055 (1) EK - SLIDE RAIL 8' GREEN RIGHT - A100054 (2) M78 - CENTER SLIDE BRACE - W100545 5/8"x3 3/8"x17 1/4" (16x86x438) SLIDE ASSEMBLY STEP 2 EK (24) M78 EL NOTE: MAKE CERTAIN SUPPORTS AND SLIDE BED ARE FULLY ENGAGED WITHIN CHANNEL OF SLIDE RAILS. SCREW PFH 8x3 (24 PLCS) TIP: A HELPER IS REQUIRED FOR THIS STEP.
(1) (2) GD - L BRACKET 66x66x127 - A100140 SB74 - SWING BEAM - W102304 2"x5 1/4"x89 1/2" (50x134x2274) (2) QZ - TRIANGLE PLATE 100° 5 HOLE - A100294 SWING BEAM ASSEMBLY BOLT WH 5/16x1 3/4 STEP 1 BOLT HEX 5/16x2-3/4 ATTACH (2) QZ TRIANGLE PLATES TO SB74 SWING BEAM USING 1-3/4" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS. WASHER LOCK EXT 12x19 WASHER FLAT 8x27 ATTACH (2) GD L BRACKETS TO SB74 SWING BEAM USING 2-3/4" HEX BOLTS, FLAT WASHERS AND 5/16" LOCK NUTS.
(1) W71 - SWING BEAM SUPPORT - W102349 2"x3 3/8"x45 7/8" (50x86x1165) (1) H79 - END SUPPORT - W100992 1"x3 1/2"x42" (24x86x1072) (2) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (1) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) SWING BEAM ASSEMBLY BOLT WH 5/16x2 BOLT WH 5/16x2 1/2 STEP 2 INSERT (2) 2-1/2" BOLTS, LOCK WASHERS AND 1-1/2" BARREL NUTS INTO TOP EDGE OF W71 SWING BEAM SUPPORT, AS SHOWN.
SWING BEAM ASSEMBLY STEP 3 ATTACH (2) QZ TRIANGLE PLATES TO W71 SWING BEAM SUPPORT USING 1-3/4" BOLTS, LOCK WASHER AND 7/8" BARREL NUT.
SWING BEAM ASSEMBLY WASHER FLAT 8x27 STEP 4 INSERT SWING HANGER QUICK LINK AND SAFETY WASHER INTO HOLES IN THE EDGE OF SB74 SWING BEAM. SECURE SWING HANGER TO W71 SWING BEAM USING FLAT WASHERS AND 5/16" LOCK NUTS.
4' Rock Ladder Phase 1 Phase Notes • Assemble slats to rails as shown. • Note oreintation of slats, be sure to arrange as shown. • See drawing below for slat spacing on rails. • Using slats as a guide, pre-drill top edges of rails with a 1/8" drill bit. Failure to pre-drill may result in board splitting. SCREW PFH 8x1 1/2 TOP M71 M72 THESE SURFACES FLUSH BOTH SIDES H73 PRE-DRILL TOP EDGE OF RAILS QTY.
4' Rock Ladder Phase 2 & 3 P h a s e N o te s BOLT FA 3/8x1 1/2 • Oreint top edge of rocks with top edge of slats. • Fasten rocks as shown. T-NUT 3/8 CLIMBING ROCK GREEN SMALL QTY. DESCRIPTION 6 CLIMBING ROCK GREEN SMALL 6 BOLT FA 3/8x1-1/2 6 T-NUT 3/8 SCREW PFH 8x1 1/8 QTY.
Fort Assembly Phase 1 Parts needed: Hardware needed: • (14) D - NUT BARREL WH 5/16x7/8 - H100005 • (14) AD - WASHER LOCK EXT 12x19 - H100031 • (16) AC - WASHER LOCK EXT 8x19 - H100030 • (10) K - BOLT WH 5/16x/2 - H100012 • (4) H - BOLT WH 5/16x1-1/2 - H100010 • (2) BS - SCREW PFH 8x1-3/4 - H100089 • (2) Z - LAG SCREW WH 5/16x2 - H100027 • (1) H1 - ROOF CROSS BRACE - W101538 • (2) E2 - FORT UPRIGHT - W101520 • (1) N1 - WALL RAIL - W101624 • (1) G2 - SWING BEAM SUPPORT - W101623 • (1) K4 - WALL RAIL - W10
Fort Assembly Phase 2 Parts needed: Hardware needed: • (1) H1 - ROOF CROSS BRACE - W101538 • (2) E1 - FORT UPRIGHT - W101519 • (1) K3 - ARCHED WALL RAIL - W101530 • (1) G1 - GROUND BOARD - W101529 • (10) D - NUT BARREL WH 5/16x7/8 - H100005 • (10) AD - WASHER LOCK EXT 12x19 - H100031 • (10) AC - WASHER LOCK EXT 8x19 - H100030 • (6) K - BOLT WH 5/16x/2 - H100012 • (4) H - BOLT WH 5/16x1-1/2 - H100010 Phase Notes • Assemble with hardware as shown.
Fort Assembly Phase 3 Parts needed: Hardware needed: • (2) M3 - TARP SUPPORT - W101539 • (1) M4 - FLOOR/TARP SUPPORT - W101541 • (3) K1 - WALL RAIL - W101528 • (1) K2 - ARCHED WALL RAIL - W101531 • (1) M5 - WALL RAIL - W101522 • (1) M13 - WALL RAIL - W4L05295 • (8) CK - SCREW PFH 8x2 - H100111 • (4) BP - SCREW PFH 8x1-1/2 - H100086 • (20) Z - LAG SCREW WH 5/16x2 - H100027 • (20) AC - WASHER LOCK EXT 8x19 - H100030 Phase Notes • Assemble with hardware as shown.
Fort Assembly Phase 4 Hardware needed: Parts needed: • (4) BT - SCREW PFH 8x2-1/2 - H100090 • (4) N10 - BOLT WH 5/16x2-3/4 - H100015 • (8) AC - WASHER LOCK EXT 8x19 - H100030 • (4) AD - WASHER LOCK EXT 12x19 - H100031 • (4) D - NUT BARREL WH 5/16x7/8 - H100005 • (4) Z - LAG SCREW WH 5/16x2 - H100027 • (1) H4 - FLOOR BRACE - W101631 • (2) H2 - FLOOR JOIST - W101521 • (4) H10 - FLOOR BRACE - W101534 • (2) F1 - ANGLE BRACE - W101630 Phase Notes • Assemble with hardware as shown.
Fort Assembly Phase 5 Hardware needed: Parts needed: • (40) CK - SCREW PFH 8x2 - H100111 • (20) BQ - SCREW PFH 8x1-1/4 - H100087 • (2) M7 - FLOOR BOARD - W101524 • (8) M2 - FLOOR BOARD - W101525 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with a 1/8" drill bit, before attaching. Note: It is vital that the fort be level before and after each phase of assembly.
Fort Assembly Phase 6 Parts needed: Hardware needed: • (2) M11 - WALL RAIL - W101527 • (2) M10 - WALL RAIL - W101621 • (1) M6 - WALL RAIL - W101523 • (1) H2 - FLOOR JOIST - W101521 • (2) K - BOLT WH 5/16x2 - H100012 • (8) AC - WASHER LOCK EXT 8x19 - H100030 • (4) AD - WASHER LOCK EXT 12x19 - H100031 • (4) D - NUT BARREL WH 5/16x7/8 - H100005 • (2) H - BOLT WH 5/16x1-1/2 - H100010 • (4) Z - LAG SCREW WH 5/16x2 - H100027 Phase Notes • Assemble with hardware as shown.
Fort Assembly Phase 7 Parts needed: Hardware needed: • (2) H6 - WALL SLAT - W101535 • (2) EJ - L BRACKET GREEN - A100053 • (8) BQ - SCREW PFH 8x1-1/4 - H100087 • (4) BL - SCREW TAPPING 14x3/4 - H100083 Phase Notes Note: Due to the changing size of the wood as a result of moisture content, you may need to adjust the spacing of your wall slats 1/16" to 1/8" when assembling walls. It would be best to line up the boards on the wall before attaching to estimate if a larger or smaller gap is needed.
Fort Assembly Phase 8 Parts needed: Hardware needed: • (4) M12 - WALL SLAT - A101536 • (8) BR - SCREW PFH 8x1-1/8 - H100088 • (8) BQ - SCREW PFH 8x1-1/4 - H100087 Phase Notes Note: Do not overtighten screws, overtightening may cause the screw to stick through the boards and may cause sharp points. The head of the screw should NOT sink into the wood for this phase, it should be flush. • Assemble with hardware as shown. Note: It is vital that the fort be level before and after each phase of assembly.
Fort Assembly Phase 9 Parts needed: Hardware needed: • (5) M12 - WALL SLAT - W101536 • (2) J1 - WALL SLAT - W101622 • (2) EJ - L BRACKET GREEN - A100053 • (20) BR - SCREW PFH 8x1-1/8 - H100088 • (8) BQ - SCREW PFH 8x1-1/4 - H100087 • (4) BL - SCREW TAPPING 14x3/4 - H100083 Phase Notes • Assemble with hardware as shown. K1 M12 Note: Do not overtighten screws, overtightening may cause the screw to stick through the boards and may cause sharp points.
Fort Assembly Phase 10 Parts needed: Hardware needed: • (2) H5 - PICNIC TARP SUPPORT - W101542 • (1) M3 - TARP SUPPORT - W101539 • (2) Z - LAG SCREW WH 5/16x2 - H100027 • (2) AC - WASHER LOCK EXT8x19 - H100030 • (4) CK - SCREW PFH 8x2 - H100111 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with a 1/8" drill bit, before attaching.
Fort Assembly Phase 11 Parts needed: Hardware needed: • (2) H8 - PICNIC SUPPORT - W101628 • (2) F2 - ANGLE BRACE - W101629 • (3) M2 - FLOOR BOARD - W101525 • (1) M8 - PICNIC CLEAT - W101632 • (2) BG - T-NUT 5/16 - H100074 • (8) AC - WASHER LOCK EXT 8x19 - H100030 • (2) L - BOLT WH 5/16x2-1/4 - H100013 • (6) Z - LAG SCREW WH 5/16x2 - H100027 • (12) CK - SCREW PFH 8x2 - H100111 • (6) BR - SCREW PFH 8x1-1/8 - H100088 Phase Notes • Assemble with hardware as shown.
Fort Assembly Phase 12 Parts needed: Hardware needed: • (2) H7 - PICNIC SUPPORT - W101625 • (2) G3 - PICNIC SUPPORT - W101627 • (2) H9 - PICNIC SUPPORT - W101626 • (2) M2 - FLOOR BOARD - W101525 • (1) M9 - PICNIC CLEAT - W101633 • (8) D - NUT BARREL WH 5/16x7/8 - H100005 • (8) AD - WASHER LOCK EXT12x19 - H100031 • (8) AC - WASHER LOCK EXT8x19 - H100030 • (8) H - BOLT WH 5/16x1-1/2 - H100010 • (6) BS - SCREW PFH 8x1-3/4 - H100089 • (8) CK - SCREW PFH 8x2 - H100111 • (4) BR - SCREW PFH 8x1-1/8 - H100088 P
Fort Assembly Phase 13 Parts needed: Hardware needed: • (2) M1 - TARP SUPPORT - W101540 • (1) M4 - FLOOR / TARP SUPPORT - W101541 • (2) B - NUT BARREL WH 5/16x5/8 - H100004 • (2) D - NUT BARREL WH 5/16x7/8 - H100005 • (4) AD - WASHER LOCK EXT12x19 - H100031 • (4) AC - WASHER LOCK EXT8x19 - H100030 • (4) F - BOLT WH 5/16x1 - H100008 • (4) BP - SCREW PFH 8x1-1/2 - H100086 Phase Notes • Assemble with hardware as shown. Note: It is vital that the fort be level before and after each phase of assembly.
Fort Assembly Phase 14 Parts needed: Hardware needed: • (1) KC - ROOF TARP - A100196 • (6) CY - SCREW PWH 8x5/8 - H100128 Phase Notes • Assemble with hardware as shown. KC M3 CY KC CY Step 1: Drape 'KC' Tarp over 'M4' floor / tarp support and 'M3' tarp supports. Attach one side of tarp to the inside of 'M3' with (3) Screws 'CY'. Pull other side of tarp tight and attach to the inside of other 'M3' tarp support using (3) Screws 'CY', as shown.
Fort Assembly Phase 15 Parts needed: Hardware needed: • (1) KB - PICNIC TABLE TARP - A100195 • (6) CY - SCREW PWH 8x5/8 - H100128 Phase Notes • Assemble with hardware as shown. KB CY M4 Step 1: Drape 'KB' Tarp over 'M4' floor / tarp support and 'M3' tarp supports. Attach one side of tarp to the inside of 'M3' with (3) Screws 'CY'. Pull other side of tarp tight and attach to the inside of 'M4' tarp support using (3) Screws 'CY', as shown.
Fort Assembly Phase 16 Parts needed: Hardware needed: • (2) EA - HAND GRIP YELLOW PLASTIC - A100043 • (4) AZ - BOLT PTH 1/4x1-1/4 - H100062 • (4) CG - WASHER LOCK EXT 8x15 - H100108 • (4) CE - WASHER FLAT 9x18 - H100106 • (4) BE - T-NUT 1/4 - H100072 Phase Notes • Assemble with hardware as shown. H6 CE CG AZ BE EA AZ DA CE CG Step 1: Attach 'EA' Hand Grip to 'H6' wall slat using Screw 'AZ', Washers 'CG' & 'CE', and T-Nuts 'BE', as shown.
Rock Ladder Attachment Phase 17 Hardware needed: Parts needed: • (2) AA - LAG SCREW WH 5/16x2-1/2 - H100028 • (2) AC - WASHER LOCK EXT 8x19 - H100030 • (1) ROCK WALL LADDER ASSEMBLY Phase Notes • Assemble with hardware as shown. AC To prevent board splitting, you must pre-drill each board with a 1/8" drill bit, before attaching.
Slide Attachment Phase 18 Hardware needed: Parts needed: • (3) BG - T-NUT 5/16 - H100074 • (3) CM - BOLT WH 5/16x1/2 - H100115 • (1) SLIDE ASSEMBLY Phase Notes 12 3/4" • Assemble with hardware as shown. 9" 2 3/4" 1" 1 7/16" To prevent board splitting, you must pre-drill each board with a 1/8" drill bit, before attaching. DRILLING DIAGRAM CM Step 1: Center the wave slide assembly in the opening opposite the swing beam assembly, as shown.
Swing Beam Attachment Parts needed: Phase 19 Hardware needed: • (1) SWING BEAM ASSEMBLY • (1) HC - BACKYARD DISCOVERY ID TAG - A100164 • (1) SR - "B" REVISION TAG - A100315 • (4) BG - T-NUT 5/16 - H100074 • (4) BX - WASHER SPLIT 5/16 - H100095 • (4) CD - WASHER FLAT 8x27 - H100105 • (4) AJ - BOLT HEX 5/16x1-1/4 - H100042 • (6) CY - SCREW PFH 8x5/8 - H100128 Phase Notes • Assemble with hardware as shown.
Anchoring Instructions Phase 20 Parts needed: Hardware needed: • (6) KD - PLASTIC GROUND STAKE BROWN - A100179 • (6) FA - QUICK LINK - A100069 • (4) EZ - CHAIN GREEN 51.25" - A100068 • (2) FB - SWING SEAT YELLOW - A100070 • (2) FW - CHAIN GREEN 31" - A100177 • (1) KF - PLASTIC TRAPEZE BAR YELLOW - A6P00034 • (6) CK - SCREW PFH 8x2 - H100111 Phase Notes • Assemble with hardware as shown. • Install the screw into the upright so that the tip of the screw does not stick through.
Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories.
