Atlantis Wooden Swing Set Model: #65210 • • Owner's Manual Frequently Asked Questions • Assembly Instructions • Warranty Information Manufacturer: Backyard Discovery 3305 Airport Drive Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetsonline.com (you will also find any updates on assembly instructions and information to order replacement parts). Features the fastening system.
STOP PARE Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com ¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA! La tienda donde realizó la compra no almacena piezas de este producto.
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing material washing away during heavy rains. 3.
Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth Wood Chips Double-Shredded bark mulch Engineered Wood Fibers Fine Sand Coarse Sand Fine Gravel Medium Gravel 6" (152mm) 7' (2.13m) 6' (1.83m) 6' (1.83m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 9" (228mm) 10' (3.05m) 10' (3.05m) 7' (2.13m) 5' (1.52m) 5' (1.52m) 7' (2.
Owner’s Manual Play Set 18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that they cannot be looped back on it. 19. Instruct children not to attach items to the playground equipment that are not specifically designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and chain as they may cause a strangulation hazard. 20. Instruct children to never wrap their legs around swing chain. 21.
Owner’s Manual Play Set Additional Maintenance: • Check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. • Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear. Light sand may be necessary to maintain a safe playing environment.
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 X3.
Owner’s Manual Play Set The American Society for Testing and Materials takes no position respecting the validity of any parent right asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such parent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Play Set Assembly Manual FAQs: 1. Does the area for the playset need to be level? Yes. Backyard Discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3.
www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the assembly manual and get the tools ready for the job as recommended in the manual. If the assembly manual is lost or misplaced a new one can be printed from Backyard Discovery’s website: www.swingsetsonline.com. 9. The playset seems to rock or sway too much. What’s wrong? Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground rails.
Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.
Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 18'- 1/2" [5.5 m] 19'-8 3/4" [6 m] 7'-8 3/4" [2.4 m] 6' [1.8 m] Safe Play Zone General Information: Your set has been designed and engineered for children only and for residential use only. A maximum of 150 lbs. per child is recommended for play activities designed for individual use.
Parts Identification Wood Components (NOT TO SCALE) E1 - TOWER LEG - W102885 (1) 1 3/8"x3 3/8"x90 1/2" (36x86x2298) E2 - TOWER LEG - W102884 (1) 1 3/8"x3 3/8"x90 1/2" (36x86x2298) E3 - TOWER LEG - W100553 (2) 1 3/8"x3 3/8"x74" (36x86x1880) E4 - CLUB HOUSE LEG - W102883 (1) 1 3/8"x3 3/8"x43 3/8" (36x86x1102) E5 - CLUB HOUSE LEG - W102882 (1) 1 3/8"x3 3/8"x43 3/8" (36x86x1102) E77 - ANGLE BRACE - W100991 (2) 1 3/8"x3 3/8"x74 3/8" (36x86x1890) G1 - SWING BEAM MOUNT - W102365 (1) 1"x5 1/4"x37 3/8"
Parts Identification Wood Components (NOT TO SCALE) H74 - LEFT UPRIGHT - W100608 (1) 1"x3 3/8"x50 3/4" (24x86x1290) H75 - RIGHT UPRIGHT - W100609 (1) 1"x3 3/8"x50 3/4" (24x86x1290) H76 - LADDER RUNG - W100611 (4) 1"x3 3/8"x18 1/8" (24x86x460) H79 - END SUPPORT - W100992 (1) 1"x3 1/2"x42" (24x86x1072) H80 - GROUND BOARD - W100990 (1) 1"x3 3/8"x87 3/8" (24x86x2218) J1 - DECK BRACE - W100561 (4) 1"x2 3/8"x15 3/4" (24x60x400) K1 - BASE BOARD - W100562 (2) 5/8"x5 1/4"x63 7/8" (16x134x1624) K2 - BA
Parts Identification Wood Components (NOT TO SCALE) L3 - WALL RAIL - W100568 (1) 5/8"x4 3/8"x40" (16x112x1016) L5 - FLOOR BOARD - W100570 (2) 5/8"x4 3/8"x37 1/8" (16x112x942) L6 - BAY WINDOW HEADER - W100571 (2) 5/8"x4 3/8"x30 1/2" (16x112x774) L7 - GABLE MOON - W100572 (2) 5/8"x4 3/8"x13" (16x112x330) L8 - CLUB HOUSE WALL RAIL - W100569 (2) 5/8"x4 3/8"x40" (16x112x1016) M1 - WALL RAIL - W100573 (1) 5/8"x3 3/8"x63 7/8" (16x86x1624) M2 - FLOOR RUNNER - W100574 (1) 5/8"x3 3/8"x63 7/8" (16x86x162
Parts Identification Wood Components (NOT TO SCALE) M9 - WALL RAIL - W100581 (2) 5/8"x3 3/8"x37 1/2" (16x86x951) M10 - WALL BOARD - W100582 (2) 5/8"x3 3/8"x25" (16x86x634) M11 - WALL BOARD - W100583 (9) 5/8"x3 3/8"x20" (16x86x508) M12 - WALL BOARD - W100584 (3) 5/8"x3 3/8"x16 7/8" (16x86x428) M13 - WALL RAIL - W100585 (4) 5/8"x3 3/8"x8 1/4" (16x86x208) M14 - WALL RAIL - W100586 (2) 5/8"x3 3/8"x6 3/4" (16x86x172) M15 - WALL BOARD - W100587 (8) 5/8"x3 3/8"x4 1/8" (16x86x106) M16 - WALL BOARD - W1005
Parts Identification Wood Components (NOT TO SCALE) N3 - GABLE BOARD - W100590 (2) 5/8"x2 3/8"x31 1/2" (16x60x800) N4 - WALL BOARD - W100591 (10) 5/8"x2 3/8"x23" (16x60x584) N5 - BAY WINDOW BOARD - W100592 (6) 5/8"x2 3/8"x13 1/8" (16x60x332) N6 - GABLE BOARD - W100593 (2) 5/8"x2 3/8"x13" (16x60x330) N7 - GABLE BOARD - W100594 (4) 5/8"x2 3/8"x8" (16x60x202) N8 - WALL BOARD SUPPORT - W100595 (2) 5/8"x2 3/8"x6 3/4" (16x60x170) N9 - BAY WINDOW BOARD - W100596 (6) 5/8"x2 3/8"x6 1/4" (16x60x158) N82
Parts Identification Hardware (2) Y - LAG SCREW WH 5/16x1 1/2 - H100026 (11) CM - BOLT WH 5/16x1/2 - H100115 (20) Z - LAG SCREW WH 5/16x2 - H100027 (7) F - BOLT WH 5/16x1 - H100008 (15) AA - LAG SCREW WH 5/16x2 1/2 - H100028 (36) H - BOLT WH 5/16x1 1/2 - H100010 (4) KY - BOLT WH 1/4x1/2" - H100141 (6) J - BOLT WH 5/16x1 3/4 - H100011 (2) LC - LAG SCREW WH 1/4x1-1/2 - H100145 (9) K - BOLT WH 5/16x2 - H100012 (4) LD - LAG SCREW WH 1/4x2 - H100146 (2) M - BOLT WH 5/16x2 1/2 - H100014 (2) AN - BOLT HEX 5
Parts Identification Hardware (4) BN - SCREW PFH 8x1 - H100085 (246) BR - SCREW PFH 8x1 1/8 - H100088 (99) CK - SCREW PFH 8x2 - H100111 (26) BT - SCREW PFH 8x2 1/2 - H100090 (15) BL - SCREW TAPPING 14x3/4 - H100083 (4) CY - SCREW PWH 8x5/8 - H100128 (22) BC - SCREW PWH 8x3/4 - H100070 (4) BY - SWING HANGER QUICK LINK - H100097 (66) BP - SCREW PFH 8x1 1/2 - H100086 (4) BZ - SWING HANGER QUICK LINK - H100099 (97) BQ - SCREW PFH 8x1 1/4 - H100087 (13) AZ - BOLT PTH 1/4x1 1/4 - H100062 (13) BE - T-
Parts Identification Hardware (8) B - NUT BARREL WH 5/16x5/8 - H100004 (4) CB - WASHER SAFETY 17x30 - H100103 (66) D - NUT BARREL WH 5/16x7/8 - H100005 (24) CD - WASHER FLAT 8x27 - H100105 (2) C - NUT BARREL WH 5/16x1 1/2 - H100006 (7) CE - WASHER FLAT 9x18 - H100106 (19) E - NUT BARREL WH 5/16x1 3/4 - H100007 (13) CG - WASHER LOCK INT 8x15 - H100108 (4) BX - WASHER SPLIT 5/16 - H100095 (4) KV - WASHER LOCK EXT 6x15 - H100138 (4) KW - WASHER LOCK EXT 8x15 - H100139 (4) KS - NUT BARREL WH 1/4x5/8 -
Parts Identification Accessories (NOT TO SCALE) (2) - T-30 Torx Bit - H100147 (2) - T-40 Torx Wrench - A100041 (1) EL - SLIDE RAIL 8' GREEN LEFT - A100055 (2) - T-40 Torx Bit - A100042 (2) - T-30 Torx Wrench - H100114 (1) EK - SLIDE RAIL 8' GREEN RIGHT - A100054 (1) EM - SLIDE BED 8' YELLOW - A100056 (1) DN - GLIDER SEAT DARK GREEN - A100025 (2) FB - SWING SEAT YELLOW - A100070 (2) DO - CAPTAINS GLIDER ARM YELLOW - A100026 (1) HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 (5) GK - WINDOW FRAME
Parts Identification Accessories (NOT TO SCALE) (7) ES - L BRACKET GREEN 32x51 -A100061 (2) (6) EV - CLIMBING ROCK - GREEN -A100064 GD - L BRACKET 66x66x127 -A100140 EY - TUBING CAP GLIDER SUPPORT -A100067 EX - GLIDER BUSHING BYD GREEN BYD GREEN (2) EW - GLIDER SUPPORT -A100066 -A100065 (4) (4) (8) FA - QUICK LINK - A100069 METAL GREEN 381 c/c (4) FX - HAND GRIP-A100118 (6) KC - METAL GROUND STAKE BROWN - A100178 (4) JD - CHAIN GREEN 45" - A100092 (4) EZ - CHAIN GREEN 51.
(1) SB74 - SWING BEAM - W102304 2"x5 1/4"x89 1/2" (50x134x2274) (2) GD - L BRACKET 66x66x127 - A100140 (2) QZ - TRIANGLE PLATE 100 5 HOLE - A100294 SWING BEAM ASSEMBLY STEP 1 ATTACH (2) QZ TRIANGLE PLATES TO SB74 SWING BEAM USING (3) 1-3/4" BOLTS, LOCK WASHER AND 7/8" BARREL NUT. ATTACH (2) GD L BRACKETS TO SB74 SWING BEAM USING (2) 2-3/4" HEX BOLTS, (4) FLAT WASHERS AND (2) 5/16" LOCK NUTS.
(1) W71 - SWING BEAM SUPPORT - W102349 2"x3 3/8"x47 3/8" (50x86x1204) (1) H79 - END SUPPORT - W100992 1"x3 1/2"x42" (24x86x1072) (2) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (1) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) STEP 2 INSERT (2) 2-1/2" BOLTS, LOCK WASHERS AND 1-1/2" BARREL NUTS INTO TOP EDGE OF W71 SWING BEAM SUPPORT, AS SHOWN. ATTACH E77 ANGLE BRACES TO W71 SWING BEAM SUPPORT USING 4- 1/2" BOLT, LOCK WASHERS AND 7/8" BARREL NUT.
(4) EX - GLIDER BUSHING BYD GREEN - A100066 (4) EY - TUBING CAP GLIDER SUPPORT - A100067 (2) EW - GLIDER SUPPORT BYD GREEN - A100065 STEP 3 ATTACH (2) QZ TRIANGLE PLATES TO W71 SWING BEAM SUPPORT USING (2) 1-3/4" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS (FIG.1). (2) LAG SCREW (2)WH 5/16x2-1/2 INSERT (4) SWING HANGER QUICK LINKS INTO (4) EX BUSHINGS AND THEN ATTACH SWING HANGER QUICK LINKS TO EW GLIDER SUPPORTS USING (4) FLAT WASHERS AND 5/16" LOCK NUTS, AS SHOWN (FIG.2).
8 FOOT SLIDE ASSEMBLY PHASE 1 STEP 1 TOP ● PLACE SLIDE BRACE CENTERED ON THE BOTTOM 1/4" FROM THE EDGE. TRANSFER HOLES ON THE BOARD THROUGH THE SLIDE BED AS SHOWN BELOW. USE A 3/8" DRILL BIT. ● ATTACH SLIDE BRACE TO SLIDE USING HARDWARE SHOWN. QTY 1 3 3 1 DESCRIPTION SLIDE BRACE BOLT WH 5/16x1/2 T - NUT 5/16 SLIDE BED 8' YELLOW (SEE SLIDE ASSEMBLY INSTALLATION STEP FOR TOP MOUNTING HOLE DRILLING LOCATIONS).
8 FOOT SLIDE ASSEMBLY PHASE 2 STEP 2 ● PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE SLIDE RAIL (FIG. 1). PUT SLIDE SUPPORT BOTTOM INTO THE SUPPORT POCKET AT THE BOTTOM OF THE RAIL AND HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT THE BED INTO THE SLIDE CAVITY. MAKE SURE SLIDE BED IS COMPLETELY DOWN IN THE SLIDE CAVITY. SECURE USING (12) 2-1/2" WOOD SCREWS AT EACH OF THE PILOT HOLE LOCATIONS AS SHOWN BELOW.
(1) E1 - TOWER LEG - W102885 1 3/8"x3 3/8"x90 1/2" (36x86x2298) (2) K1 - BASE BOARD - W100562 5/8"x5 1/4"x63 7/8" (16x134x1624) (1) L1 - LEFT WALL RAIL - W102360 5/8"x4 3/8"x63 7/8" (16x112x1624) (1) E2 - TOWER LEG - W102884 1 3/8"x3 3/8"x90 1/2" (36x86x2298) (1) N1 - SWING BLOCK - W100588 5/8"x2 3/8"x63 7/8" (16x60x1624) (1) H2 - RIGHT FLOOR RAIL - W100558 1"x3 3/8"x63 7/8" (24x86x1624) E3 - TOWER LEG - W100553 1 3/8"x3 3/8"x74" (36x86x1880) (1) H1 - LEFT FLOOR RAIL - W100557 1"x3 3/8"x63 7/8
(2) K2 - BASE BOARD - W100563 5/8"x5 1/4"x40" (16x134x1016) (1) K3 - FRONT ARCH - W100564 5/8"x5 1/4"x40" (16x134x1016) (2) M8 - WALL RAIL - W100580 5/8"x3 3/8"x40" (16x86x1016) (1) L3 - WALL RAIL - W100568 5/8"x4 3/8"x40" (16x112x1016) (1) (1) M6 - FLOOR RAIL - W100578 5/8"x3 3/8"x40" (16x86x1016) L8 - CLUB HOUSE WALL RAIL - W100569 5/8"x4 3/8"x40" (16x112x1016) STEP 3 STAND UP UPRIGHT ASSEMBLIES AND ATTACH (2) K2 GROUND BOARDS TO E1 & E2 TOWER LEGS AND TO (2) E3 TOWER LEGS USING (8) 2-3/4" BOL
(4) J1 - DECK BRACE - W100561 1"x2 3/8"x15 3/4" (24x60x400) (16) M3 - FLOOR BOARD - W100575 5/8"x3 3/8"x41 7/8" (16x86x1064) (2) L5 - FLOOR BOARD - W100570 5/8"x4 3/8"x37 1/8" (16x112x942) (1) N2 - FLOOR BOARD - W100589 5/8"x2 3/8"x41 7/8" (16x60x1064) STEP 4 ATTACH (2) J1 DECK BRACES TO M6 FLOOR RAIL USING (2) 1" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS.
(1) M2 - FLOOR RUNNER - W100574 5/8"x3 3/8"x63 7/8" (16x86x1624) (2) ES - L BRACKET GREEN 32x51 - A100061 STEP 6 ATTACH (2) ES L BRACKETS TO THE ENDS OF M2 FLOOR RUNNER USING (2) 3/4" TAPPING SCREWS. ATTACH ES L BRACKETS AND M2 FLOOR RUNNER TO M6 & M8 BOARDS USING (2) 3/4" TAPPING SCREWS. (4) SCREW TAPPING 14x3/4 ATTACH M2 FLOOR RUNNER TO M3, M5 & N2 FLOOR BOARDS USING (17) 1-1/8" SCREWS.
(1) M1 - WALL RAIL - W100573 5/8"x3 3/8"x63 7/8" (16x86x1624) (2) M13 - WALL RAIL - W100585 5/8"x3 3/8"x8 1/4" (16x86x208) (1) M8 - WALL RAIL - W100580 5/8"x3 3/8"x40" (16x86x1016) (1) M14 - WALL RAIL - W100586 5/8"x3 3/8"x6 3/4" (16x86x172) STEP 7 ATTACH M1 WALL RAIL TO E1 & E3 TOWER LEGS USING (2) 2" LAG SCREWS AND LOCK WASHERS. (1) ATTACH M13 WALL RAIL TO E1 & E2 TOWER LEGS USING (2) 2" LAG SCREW AND LOCK WASHER. ATTACH M8 WALL RAIL TO E3 TOWER LEGS USING (2) 2" LAG SCREWS AND LOCK WASHERS.
(1) E4 - CLUB HOUSE LEG - W102883 1 3/8"x3 3/8"x43 3/8" (36x86x1102) (2) M13 - WALL RAIL - W100585 5/8"x3 3/8"x8 1/4" (16x86x208) (1) ES - L BRACKET GREEN 32x51 - A100061 (1) E5 - CLUB HOUSE LEG - W102882 1 3/8"x3 3/8"x43 3/8" (36x86x1102) (1) M14 - WALL RAIL - W100586 5/8"x3 3/8"x6 3/4" (16x86x172) STEP 8 ATTACH E4 CLUB HOUSE LEG TO L2 RIGHT WALL RAIL USING (2) 1-1/2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS.
(1) G1 - SWING BEAM MOUNT - W102365 1"x5 1/4"x37 3/8" (24x134x950) (1) L8 - CLUB HOUSE WALL RAIL - W100569 5/8"x4 3/8"x40" (16x112x1016) (2) M9 - WALL RAIL - W100581 5/8"x3 3/8"x37 1/2" (16x86x951) STEP 9 USING A HAMMER, INSERT (4) 5/16 T-NUTS INTO G1 SWING BEAM MOUNT. ATTACH M9 WALL RAIL TO E1 TOWER LEG AND E5 CLUB HOUSE LEG USING (4) 1- 1/2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS.
(4) H3 - ROOF RAFTER - W100559 1"x3 3/8"x34" (24x86x864) (2) N3 - GABLE BOARD - W100590 5/8"x2 3/8"x31 1/2" (16x60x800) (2) L7 - GABLE MOON - W100572 5/8"x4 3/8"x13" (16x112x330) (2) N6 - GABLE BOARD - W100593 5/8"x2 3/8"x13" (16x60x330) (4) N7 - GABLE BOARD - W100594 5/8"x2 3/8"x8" (16x60x202) STEP 10 ATTACH N6 GABLE BOARD TO (2) H3 ROOF RAFTERS USING (2) 1-1/4" WOOD SCREWS. ATTACH N3 GABLE BOARD TO (2) H3 ROOF RAFTERS USING (4) 1-1/4" WOOD SCREWS.
(2) M17 - WALL RAIL - W102881 5/8"x3 3/8"x40" (16x86x1016) GABLE END ASSEMBLY STEP 11 MEASURE DOWN 15/16" FROM TOP OF E1 & E2 LEGS AND PILOT DRILL USING 1/8" DRILL BIT APPROXIMATELY 2" DEEP FOR H3 AND M8 BOARD ATTACHMENT. SEE FIGURE 1. ATTACH GABLE END ASSEMBLY AND M17 WALL RAIL TO E1 & E2 TOWER LEGS USING (2) 2-1/2" LAG SCREWS AND LOCK WASHERS. TOP OF BOARD q LAG SCREW GABLE END ASSEMBLY (2)WH 5/16x2-1/2 15/16" E1 & E2 (2) WASHER LOCK EXT 8x19 M17 FIG.
(2) M7 - WALL BOARD - W100579 5/8"x3 3/8"x40" (16x86x1016) (9) M11 - WALL BOARD - W100583 5/8"x3 3/8"x20" (16x86x508) (6) N4 - WALL BOARD - W100591 5/8"x2 3/8"x23" (16x60x584) STEP 13 ATTACH N4 WALL BOARDS TO M8 & L3 WALL RAILS USING (12) 1-1/8" WOOD SCREWS. SEE ILLUSTRATION FOR SPACING AND MOUNTING DIMENSIONS. ATTACH (2) M7 WALL BOARDS AND TO K2 BASE BOARD, M8 WALL RAIL & K3 FRONT ARCH USING (10) 1-1/8" WOOD SCREWS. SEE ILLUSTRATION FOR MOUNTING DIMENSIONS.
(4) M5 - WALL BOARD - W100577 5/8"x3 3/8"x42" (16x86x1066) (2) N8 - WALL BOARD SUPPORT - W100595 5/8"x2 3/8"x6 3/4" (16x60x170) (2) ES - L BRACKET GREEN 32x51 - A100061 STEP 14 ATTACH (4) M5 WALL BOARDS TO M17 & M13 WALL RAILS USING (16) 1-1/8" WOOD SCREWS. ATTACH (2) N8 WALL BOARD SUPPORTS TO M5 WALL BOARDS USING (4) 1-1/8" WOOD SCREWS. ATTACH (2) ES L BRACKETS TO M3 FLOOR BOARD & M5 WALL BOARDS USING (4) 3/4" TAPPING SCREWS.
(2) M16 - WALL BOARD - W100599 5/8"x3 3/8"x42" (16x86x1066) (2) M4 - WALL BOARD - W100576 5/8"x3 3/8"x42" (16x86x1066) (3) M12 - WALL BOARD - W100584 5/8"x3 3/8"x16 7/8" (16x86x428) M15 - WALL BOARD - W100587 5/8"x3 3/8"x4 1/8" (16x86x106) (8) (2) ES - L BRACKET GREEN 32x51 - A100061 STEP 15 ATTACH (2) M4 & M16 WALL BOARDS TO M17, L8 & M13 WALL RAILS USING (20) 1-1/8" WOOD SCREWS. ATTACH (4) M15 WALL BOARDS TO M17 WALL RAIL & L8 CLUB HOUSE WALL RAIL USING (8) 1-1/8" WOOD SCREWS.
(1) K4 - TABLE TOP - W100565 5/8"x5 1/4"x37" (16x134x940) (2) H4 - TABLE SUPPORT - W100560 1"x2"x4" (24x51x102) (2) GK - WINDOW FRAME 216x267 - A100146 STEP 16 ATTACH (2) GK WINDOW FRAMES TO THE OUTSIDE OF FORT USING (8) 3/4" PWH SCREWS. (8) SCREW PWH 8x3/4 GK REAR VIEW STEP 17 USING K4 AS A TEMPLATE, PILOT DRILL USING 1/8" DRILL BIT AND ATTACH K4 TABLE TOP TO THE EDGE OF M8 WALL RAIL USING (3) 1-1/4" WOOD SCREWS.
(9) (4) M4 - WALL BOARD - W100576 5/8"x3 3/8"x42" (16x86x1066) N4 - WALL BOARD - W100591 5/8"x2 3/8"x23" (16x60x584) STEP 18 ATTACH (4) N4 WALL BOARDS TO L1 LEFT WALL RAIL AND M1 WALL RAIL USING (8) 1-1/8" WOOD SCREWS. ATTACH (9) M4 WALL BOARDS TO M1, L1 AND M9 WALL RAIL USING (45) 1-1/8" WOOD SCREWS.
(2) M10 - WALL BOARD - W100582 5/8"x3 3/8"x25" (16x86x634) STEP 19 ATTACH (2) M10 WALL BOARDS TO L2 RIGHT WALL RAIL AND M14 WALL RAILS USING (8) 1-1/8" WOOD SCREWS.
(2) (6) N9 - BAY WINDOW BOARD - W100596 5/8"x2 3/8"x6 1/4" (16x60x158) (6) N5 - BAY WINDOW BOARD - W100592 5/8"x2 3/8"x13 1/8" (16x60x332) L6 - BAY WINDOW HEADER - W100571 5/8"x4 3/8"x30 1/2" (16x112x774) (3) GK - WINDOW 216x267 GREEN - A100146 STEP 20 STARTING IN THE CENTER, PILOT DRILL USING 1/8" DRILL BIT AND ATTACH N9 BAY WINDOW BOARDS TO THE EDGE OF (2) L6 BAY WINDOW HEADERS USING (4) 1" SCREWS IN CORNERS AND 1-1/8" SCREWS.
(1) (1) H74 - LEFT UPRIGHT - W100608 1"x3 3/8"x50 3/4" (24x86x1290) (1) H75 - RIGHT UPRIGHT - W100609 1"x3 3/8"x50 3/4" (24x86x1290) (4) M73 - REAR SUPPORT - W100610 5/8"x3 3/8"x19 1/4" (16x86x488) H76 - LADDER RUNG - W100611 1"x3 3/8"x18 1/8" (24x86x460) STEP 22 ATTACH (4) H76 LADDER RUNGS TO H74 LEFT UPRIGHT USING (8) 2" WOOD SCREWS. ATTACH H75 RIGHT UPRIGHTS TO H76 LADDER RUNGS USING (8) 2" WOOD SCREWS. ATTACH M73 REAR SUPPORT TO H74 & H75 UPRIGHTS USING (4) 2" WOOD SCREWS.
(14) R1 - ROOF BOARD - W100597 3/4"x5 1/2"x42 1/2" (18x140x1080) (4) FX - HAND GRIP METAL GREEN 381 c/c - A100118 STEP 24 USING FX HAND GRIP AS A TEMPLATE, PILOT DRILL USING 7/16" BIT AND ATTACH TO E3 TOWER LEG USING (2) 1" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS. ATTACH FX HAND GRIP TO E4 CLUB HOUSE LEG USING (2) 1" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS.
(2) (1) H73 - ROCK WALL RAIL - W102361 24"x86"x1237" (24x86x1237) N82 - ROCKWALL TOP CAP - W102364 5/8"x2 3/8"x20 1/4" (16x60x514) (6) EV - CLIMBING ROCK - GREEN - A100064 (8) M72 - ROCK WALL BOARD - W102362 5/8"x3 3/8"x20 1/4" (16x86x514) (6) N83 - ROCK WALL BOARD HOLES - W102363 5/8"x3 3/8"x20 1/4" (16x86x514) STEP 26 START BY ATTACHING THE EV CLIMBING ROCKS TO N83 ROCK WALL BOARDS USING (12) 1-1/4" BOLTS, LOCK WASHERS, AND 1/4" T-NUTS.
STEP 28 CENTER SLIDE ASSEMBLY IN OPENING, AS SHOWN. USING THE DRILLING PATTERN BELOW, PILOT DRILL (3) HOLES INTO M3 FLOOR BOARDS USING 7/16" DRILL BIT AND ATTACH SLIDE ASSEMBLY USING (3) 1/2" BOLTS, LOCK WASHERS AND 5/8" BARREL NUTS.
STEP 29 ATTACH SWING BEAM ASSEMBLY TO G1 SWING BEAM MOUNT USING (4) 1-1/4" HEX BOLTS, SPLIT WASHERS AND FLAT WASHERS. (4) ATTACH HC ID PLATE TO SWING BEAM USING (4) 5/8" SCREWS, AS SHOWN.
CAPTAINS GLIDER (2) NUT LOCK 5/16 (2) WASHER FLAT 8x27 Notes • Assemble using hardware as shown.
(6) KC - METAL GROUND STAKE BROWN - A100178 (2) FB - SWING SEAT YELLOW - A100070 (8) FA - QUICK LINK - A100069 (4) EZ - CHAIN GREEN 51.25" - A100068 Anchoring Instructions (4) NOTE: BOLT WH 1/4x1/2" LAG SCREW (2)WH 1/4x1-1/2 FAILURE TO USE STAKES CAN VOID WARRANTY & CAUSE INJURY! (4) STEP 30 STAKE STAKE TWIST STAKES INTO GROUND AGAINST SWING BEAM GROUND BOARDS WHERE SHOWN AND ATTACH TO SWING BEAM WITH (2) 1-1/2" LAG SCREWS AND FLAT WASHERS.
Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories.
