Owner’s Manual FAQ’s Assembly Instructions Warranty Information Atlantis Wooden Playcenter - 2010 Model: 65210 Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 Made in China 65210 Atlantis Ver 5-09-1205
Title Page PS Rev. 01/28/2009 Tools Required for Installation: (These are the tools that are generally required for assembly of our playsets. These tools are not included in the playset purchase.
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play set tipping ove r and loose-fill surfacing material washing away during heavy rains. 3.
Owner’s Manual Play Set Operating Instructions: NOTE : Your children’s safety is our #1 concern. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. Please review these safety rules regularly with your children. 1. This Playcenter is designed for specific number of occupants whose combined weight should not exceed a designated weight on the elevated floor or the swing area, the total Unit capacity is outlined in the assembly section of instruction manual.
Owner’s Manual Play Set Maintenance Instructions: 1. Check all nuts and bolts twice monthly during the usage season and tighten as required. (But not so tight that you crack the wood) We recommend you check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. 2. Remove plastic swing seats and take indoors or do not use when the temperature drops below 32 ° F. 3.
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission's Information Sheet for playground surfacing material Also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS11 X3.1 The U.S.
Play Set Assembly Manual FAQs: 1. Does the area for the playset need to be level? Yes. Backyard Discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3.
However, Backyard Discovery playsets are designed and constructed using the actual dimensions so everything fits properly and remains so during the life of the playset. 11. The end beam is not straight up and down. Why not? This is normal. Backyard Discovery designs playsets this way to ensure the strongest structure possible. The slight angle adds strength and reduces rocking and twisting. 12. The S-hooks for the swings won’t close.
USING THE HARDWARE LEISURE TIME PRODUCTS, INC GYM SETS USE A FEW STANDARD CONNECTIONS. BECOMING FAMILIAR WITH THESE CONNECTIONS WILL SIMPLIFY ASSEMBLY AND INSURE A SAFER PLAY PRODUCT FOR YOUR CHILDREN. How to use Safe-T-Fuse Fasteners Barrel Nut Lock Washer WHA Bolt Correct Assembly Lock Washer Flat Washer Check the positioning of parts in each Step's illustration, noting which of the parts should receive the Lock Washer and Barrel Nut. Place the Barrel Nut and Lock Washer in the hole.
Atlantis Model #65210 Assembly Requires Two Moderately Skilled People. If you need assistance with parts or have assembly questions, please call Customer Service at 1-800-856-4445 Please read the entire instruction manual carefully before proceeding with the assembly or use of your new gym set. SAVE THIS MANUAL for future reference in the event that you need to contact us for assistance or replacement part information and ordering.
30'-1" 18'-1" 25'-10" 7'-9 1/2" Dimensions: • The Atlantis has One layout option. Layout: Ground Dimension 7’-9½”x 18’-1” x 9’-3½” high General Information: Safe Play Area* 25’-10” x 30’-1” x 15’-3½” high *Level Ground Surface - See below • Additional accessories may increase the size of the Safe Play Area. • Max fall height 91 ½" Your set has been designed and engineered for children only and for residential use only. A maximum of 150 lbs.
N7 N6 N7 Front N3 L7 R1 H3 H3 M8 N9 G1 M15 M12 SB1 L2 E3 N8 Left M4 M4 M16 M16 M13 M5 M6 H2 P1 J1 J1 Right E1 E2 N1 M11 M21 K1 K1 K2 H10 H8 H7 H9 Back PAGE 11- PARTS LOCATOR H6
H3 NOT SHOWN H1 H4 H5 M1 M9 N6 Left N7 R1 L7 N3 M8 SB1 L4 N5 M5 L3 L2 N4 M5 M10 E4 M8 P1 M13 M3 M8 L6 E2 O1 Back M14 H2 M19 K3 M17 J1 M17 E3 M17 H6 K4 M17 M7 K1 M17 M11 M8 K1 M17 K2 M19 Front H8 PAGE 12- PARTS LOCATOR Right
E1 - TOWER LEG (W100551) - 1 REQ - 36 x 86 x 2298 (1.375 x 3.375 x 90.5) E2 - TOWER LEG (W100552) - 1 REQ - 36 x 86 x 2298 (1.375 x 3.375 x 90.5) E3 - TOWER LEG (W100553) - 2 REQ - 36 x 86 x 1880 (1.375 x 3.375 x 74) E4 - CLUB HOUSE LEG (W100554) - 1 REQ - 36 x 86 x 1102 (1.375 x 3.375 x 43.375) E5 - CLUB HOUSE LEG (W100555) - 1 REQ - 36 x 86 x 1100 (1.375 x 3.375 x 43.375) G1 - SWING BEAM MOUNT (W100556) - 1 REQ - 24 x 134 x 950 (1 x 5.25 x 37.
L2 - RIGHT WALL RAIL (W100567) - 1 REQ - 16 x 112 x 1624 (.625 x 4.375 x 64) L3 - WALL RAIL (W100568) - 1 REQ - 16 x 112 x 1016 (.625 x 4.375 x 40) L4 - CLUB HOUSE WALL RAIL (W100569) - 2 REQ - 16 x 112 x 1016 (.625 x 4.375 x 40) L5 - FLOOR BOARD (W100570) - 2 REQ - 16 x 112 x 942 (.625 x 4.375 x 37) L6 - BAY WINDOW (W100571) - 2 REQ - 16 x 112 x 774 (.625 x 4.375 x 30.5) L7 - GABLE MOON (W100572) - 2 REQ - 16 x 112 x 330 (.625 x 4.375 x 13) M1 - WALL RAIL (W100573) - 1 REQ - 16 x 86 x 1624 (.625 x 3.
M13 - WALL RAIL (W100585) - 4 REQ - 16 x 86 x 204 (.625 x 3.375 x 8) M14 - WALL RAIL (W100586) - 2 REQ - 16 x 86 x 172 (.625 x 3.375 x 6.75) M15 - WALL BOARD (W100587) - 8 REQ - 16 x 86 x 106 (.625 x 3.375 x 4.2) M16 - WALL BOARD (W100599) - 2 REQ - 16 x 86 x 1066 (.625 x 3.375 x 42) N1 - SWING BLOCK (W100588) - 1 REQ - 16 x 60 x 1624 (.625 x 2.375 x 64) N2 - FLOOR BOARD (W100589) - 1 REQ - 16 x 60 x 1064 (.625 x 2.375 x 41.875) N3 - GABLE BOARD (W100590) - 2 REQ - 16 x 60 x 762 (.625 x 2.
P1 - A-FRAME LEG (W100549) - 2 REQ - 34 x 86 x 2226 (1.375 x 3.375 x 87.625) H6 - A-FRAME GROUND BOARD (W100550) - 1 REQ - 24 x 86 x 2260 (.95 x 3.375 x 89) SB1 - SWING BEAM (W100604) - 1 REQ - 50 x 134 x 2274 (2 x 5.25 x 89.5) H9 - LADDER UPRIGHT LEFT (W100608) - 1 REQ - 24 x 86 x 1290 (.95 x 3.375 x 50.75) H10 - LADDER UPRIGHT RIGHT (W100609) - 1 REQ - 24 x 86 x 1290 (.95 x 3.375 x 50.75) M21 - LADDER REAR SUPPORT (W100610) - 1 REQ - 16 x 86 x 488 (.625 x 3.375 x 19.
0 MEASURE BOLTS FROM BOTTOM OF HEAD TO BOTTOM OF BOLT H100115 H100008 H100010 H100012 5/16 X 2" WHA BOLT 5/16 X 1 1/2" WHA H100011 BOLT 5/16 X 1 3/4" WHA BOLT 5/16 X 1" WHA BOLT 5/16 X 1/2" WHA BOLT H100042 5/16 X 1 1/4" HEX HEAD BOLT H100015 H100005 H100007 MEASURE BOLTS FROM BOTTOM OF HEAD TO BOTTOM OF BOLT H100038 H100027 H100028 5/16 X 2-1/2" LAG SCREW 5/16 X 5 3/4" WHA BOLT 5/16 X 3" LAG SCREW 1/4 X 1" PHILLIPS TRUSS HEAD BOLT H100079 1/4" BARREL HEAD NUT 5/16 X 2" CARRIAGE BOLT 1 3/4
H100110 (5/16") Lock Nut H100105 Fender Washer H100102 11 X 25 Flat Washer H100106 9 X 18 Flat Washer H100108 5/16" Internal Tooth Lock Washer H100034 Power Driver Bit Wrench H100130 8 x 19 Lock Washer H100070 #8 X 3/4" WASHER HEAD SCREW H100103 17 X 30 Washer H100031 12 x 19 Lock Washer PAGE 18 - HARDWARE NOTE: QUANTITIES INCLUDE EXTRA HARDWARE PART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . QTY. H100004. . . . . .
X11-CAY 2 - GLIDER ARMS W/CHAIN 1 -GLIDER SEAT Y20-LG Y20-RG Y20-EG 1 - LEFT SINGLE BEAM CLAMP 1 - RIGHT SINGLE BEAM CLAMP 1 - SINGLE BEAM END CLAMP Y46-5G 2 - SINGLE BEAM ATTACHMENT BRACE Y25-G GLIDER SUPPORTS X20-G6 2 REQUIRED GREEN PLASTIC ROCKS 6 REQUIRED Y10-16.5G X2-Y 16 1/2" METAL GRIP 4 REQUIRED BELT SWING 2 REQUIRED Y60-51.
ITEMS NEEDED HARDWARE NEEDED 1-H1 Lt Floor Rail 1-H2 Rt Floor Rail 2-K1 Base Boards 2-E3 Tower Legs 1-E2 Tower Legs 1-E1 Tower Leg 1-L2 Rt Wall Rail 1-L1 Lt Wall Rail 8- 5/16” x 2 ¾” Bolts 16-5/16” x 1 ½” Bolts 24-5/16” x 1” Barrel Nuts 24-Lock Washers for Bolts 24-Lock Washers for Barrel Nuts Step 1 ( Note there are different Lock Washers for Bolts and Barrel Nuts ) Attach H2 Right Floor Rail to E2 and E3 Tower Legs and H5 Floor supports with 5/16” x 2 ¾” Bolts, Lock Washers and 1” Barrel Nuts and Lock
ITEMS NEEDED HARDWARE NEEDED 2-K2 Base Boards 1-K3 Front Arch 1-L3 Wall Rail 1-L4 Club House Wall Rail 1-M8 Wall Rail 16-5/16” x 2 ¾” Bolts 4-5/16” x 2 ½” Lag Screws 4-5/16” x 2” Lag Screws 16-5/16” x 1 ¾” Barrel Nuts 24-Lock Washers for Bolts 16-Barrel Nut Lock Washers Step 2 Attach M8 Wall Rail to E3 Tower Legs with 5/16 x 2 3/4” Bolts, Lock Washers and 1 3/4” Barrel Nuts and Lock Washers. Attach K3 Front Arch to E3 Tower Legs with 5/16” x 2 ½” Lag Screws and Lock Washers.
ITEMS NEEDED HARDWARE NEEDED 4- J1 Deck Braces 2-5/16” x 1 ½” Bolts 4-5/16” x 1” Barrel Nuts 4-2 ½” Hex Lag Screws 4-Lock Washers for Bolts 4-Lock Washers for Barrel Nuts 4-5/16” Flat Washers 4-5/16” Lock Washers 2-1” Bolts Step3 Make sure set is level and plumb and attach two J1 Deck Braces to M6 Floor Rail with 5/16” x 1” Bolts, Lock Washers and 1” Barrel Nuts and Lock washers and to Tower Legs with 2 ½” Lag Screws, 5/16” Lock Washers and 5/16” Flat Washers.
ITEMS NEEDED HARDWARE NEEDED 2-L5 Floor Boards 1-M2 Floor Runner 16-M3 Floor Boards 1-N2 Floor Board 2-Y30-9G L Brackets 4- #14 x ¾” Self Tapping Screw 74- 1 ½” Wood Screws 19-1 1/8” Wood Screws Step 4 Attach two L5 Floor Boards one between E3 Tower Legs and one between E1 and E2 Tower Legs using 1 ½” Wood Screws into H5 Floor Supports. Attach eight M3 Floor Boards then one N2 Floor Board and eight more M3 Floor Boards and secure to H1 and H2 Floor Rails with 1 ½” Wood Screws.
ITEMS NEEDED HARDWARE NEEDED 1-E4 Club House Leg 1-E5 Club House Leg 1-M1 Wall Rail 4-M13 Wall Rails 2-M14 Wall Rails 6-5/16” x 1 ½” Bolts 7-5/16” x 2” Lag Screws 2-#14 x ¾” Self Tapping Screws 13- Lock Washers for Bolts 6-Lock Washers for Barrel Nuts 6-5/16” x 1”Barrel Nuts 1-Y30-9G L Brackets Step 5 Attach E4 Club House Leg to L2 arch with 5/16” x 1 ½” Bolts, Lock Washers and 1” Barrel Nuts and Lock Washers.
ITEMS NEEDED HARDWARE NEEDED 1-G1 Swing Beam Mount 2-M8 Wall Rails 2-M9 Wall Rails 2-5/16” x 2 ¾” Bolts 12-5/16” x 1” Barrel Nuts 2-5/16” x 1 3/4” Barrel Nuts 8-5/16” x 1 ½” Bolts 2-5/16” x 2” Lag Screws 4-5/16” Spike T Nuts 4-5/16” x 2” Bolts 16-Lock Washers for Bolts 14- Lock Washers for Barrel Nuts Step 6 Attach M8 Wall Rail to E3 Tower Legs with 5/16” x 2 ¾” Bolts, Lock Washers and 1 3/4” Barrel Nuts and Lock Washers.
ITEMS NEEDED HARDWARE NEEDED 4-H3 Roof Rafters 2-M8 Wall Rails 2-N3 Gable Boards 2-N6 Gable Boards 4-N7 Gable Boards 2-L7 Gable Moons 4-5/16” x 3” Lag Screws 4- Lock Washers for Bolts 20-1 ¼” Wood Screws 10-1 1/8” Wood Screws Step 7 Attach two H3 Roof Rafter and M8 Wall Rail to top of E1 and E2 Tower Legs with 5/16” x 3” Lag Screws and Lock Washers and two more H3 and one M8 to E4 and E5 Club House Legs using 5/16” x 3” Lag Screws and Lock Washers.
ITEMS NEEDED HARDWARE NEEDED 1-L4 Club House Wall Rail 4- 5/16” x 2” Lag Screws 4- Lock Washers for Bolts Step 8 Attach L4 Club House Wall Rail under M8 and to E4 and E5 Club House Legs using 5/16” x 2” Lag Screws and Lock Washers.
ITEMS NEEDED HARDWARE NEEDED 11-M4 Wall Boards 4-M5 Wall Boards 2-M10 Wall Boards 2-M16 Wall Boards 2-N8 Wall Boards 93-1 1/8” Wood Screws Step 9 Attach a M4 Wall Board against E1 and E2 Tower Legs and to M13,L4 and M8 on back side of set with 1 1/8” Wood Screws. Then attach a M16 Wall Board against M4 Wall Boards just installed with 1 1/8” Wood Screws. Attach nine M4 Wall Boards between E1 Tower Leg and E5 Club House Leg to L1 Wall Rail and M1 Wall Rail and M9 Wall Rail with 1 1/8” Wood Screws.
ITEMS NEEDED HARDWARE NEEDED 3-M12 Wall Boards 8-M15 Wall Boards 2-X40-G2 Window Frames 28- 1 1/8” Wood Screws 8-3/4” Washer Head Screws Step 10 On back side of set attach two M15 Wall Boards flush with top of M16 Wall Boards and secure to M8 Wall Rail with 1 1/8” Wood Screws, then three M12 Wall Boards flush with top of M15 and secure with 1 1/8” Wood Screws and two more M15 Wall Boards with 1 1/8” Wood Screws.
ITEMS NEEDED HARDWARE NEEDED 2- L6 Bay Window Boards 6-N5 Bay Window Boards 6-N9 Bay Window Boards 6- 1 ¼” Wood Screws 24- 1 1/8” Wood Screws 12- ¾” Washer Head Screws 3- X40-G2 Window Frames Step 11 On right side of set center a L6 Bay Window Board in opening and secure to L2 Wall Rail with 1 ¼” Wood Screws. Now secure another L6 to M9 Wall Rail with 1 ¼” Wood Screws. Starting at left side attach a N5 Bay Window Board tight against Club House wall and secure to L6 Boards with 1 1/8” Wood Screws.
ITEMS NEEDED HARDWARE NEEDED 14- R1 Roof Slats 56-1 ½” Wood Screws Step 12 Starting flush with Peak of Rafters on left side of set leaving a 1” overhang on front and back attach a R1 Roof Slat to H3 Rafters with 1 ½” Wood Screws. On right side of set flush a R1 to one previously installed on left side and secure with 1 ½” Wood Screws. Finish roof by securing six more R1 Roof Slats to each side of set. ( Note: on last R1 on each side you may need to move last screw up to hit rafter.
ITEMS NEEDED HARDWARE NEEDED 1-N1 Swing Block 10-N4 Wall Boards 20- 1 1/8” Wood Screws 2-5/16” x 2” Lag Screws 2- Lock Washers for Bolts Step 13 Attach six N4 Wall Boards to M8 and L3 Wall Rails on front wall with a 3 ¼” space using 1 1/8” Wood Screws. Attach four more to M1 and L1 Wall Rails left Wall with a 2 ¾” space using 1 1/8” Wood Screws.
ITEMS NEEDED HARDWARE NEEDED 2-H4 Table Supports 1-K4 Table Top 2-M7 wall Boards 9- M11 Wall Boards 36- 1 1/8” Wood Screws 7- 1 ¼” Wood Screws Step 15 Attach a M7 Wall Board against E3 Tower Legs on each side of front of set and secure to K2 Base Board and K3 Front Arch using 1 1/8” Wood screws. Attach nine M11 Wall Boards to K2 Base Board and M8 Wall Rail with 1 1/8” Wood Screws. Attach K4 Table Top to M8 Wall Rail using 1 ¼” Wood Screws.
ITEMS NEEDED HARDWARE NEEDED 2- H8 Rock Wall Rails 6- M17 Rock Wall Slats 8-M19 Rock Wall Slats 1-01 Rock Wall Cap 6- X20-G Rocks 2- 5/16” x 2½” Lag Screws 2- Lock Washers for Bolts 60- 1 ½” Wood Screws 2- Lock Washers for Bolts 12- 1” Phillips truss Head Bolts 12- ¼” Barrel Nuts 12- Fender Washers 12- 5/16” Internal Tooth Lock Washers Step 16 Begin Rock Wall by attaching six X20-G Rocks to M17 Rock Wall Slats with ¼” x 1” Phillips Truss Head Bolts, 5/16” Lock Washers and Fender Washers and ¼” Barrel Nu
ITEMS NEEDED HARDWARE NEEDED 1-H9 Lt Ladder Upright 1-H10 Rt Ladder Upright 1-M21 Ladder Rear Support 4-H7 Ladder Rungs 4-Y10-16.5 Hand Grips 4- 5/16” x 1” Bolts 4- 5/16” x 1” Barrel Nuts 4- 5/16” x 5/8” Barrel Nuts 4- 5/16” x ½” Bolts 2- 5/16” x 2” Lag Screws 20- 2” Wood Screws 2-Lock Washers for Bolts 8-Lock Washers for Barrel Nuts Step 18 Attach a Y10-16.5G Hand Grip to E4 Club House Leg with 5/16” x 1” Bolts,Lock Washers and 1” Barrel Nuts and Lock Washers. Attach Y10-16.
ITEMS NEEDED HARDWARE NEEDED 1-M20 Slide Brace 1-Slide Bed 3-5/16” x ½” Bolts 3-5/16”x 5/8” Barrel Nuts 3- Lock Washers for Barrel Nuts Step 20 Drill three holes at one end of the plastic slide bed using a 5/16” drill bit and using the dimensions shown in Figure 1. This end will be the top of the slide. Take note of slide bed surface finish, the dull side will be towards the ground. Place Slide Support Bottom M20 centered on the bottom (dull side) of slide bed and 1/4” from the edge.
ITEMS NEEDED HARDWARE NEEDED 2-M18 Slide Center Board 1-Right Slide Rail 1-Left Slide Rail 1-Slide Bed 24-3” Wood Screws Step 21 Place one slide rail on a flat surface and begin inserting slide bed at the bottom of the slide rail. Put slide support bottom into the support pocket at the bottom of rail and have a helper bend the slide bed towards the top of the slide and insert the bed into the slide cavity. Make sure slide bed is completely down in the slide cavity.
ITEMS NEEDED HARDWARE NEEDED 1-SB1 Swing Beam 2-PH1 A Frame Legs 1-H6 A Frame Ground Board 1-Y20-LG 1-Y20-RG 1-Y20-EG End Plate 2-Y46-5G Swing Beam Bracket 1-ID Plate 4-5/16 x 2 ¾” Hex Bolts 8-5/16” Lock Nuts 2-5/16 x 2” Lag Screws 4-5/16 x 2” Carriage Bolts 4-5/16 x 1 ¼” Hex Bolts 4-5/16” Flat Washers 4-5/16” Lock Washers 2-5/16 x 1” Bolts 14 Fender Washers 2-1 ¾ Barrel Nuts 2-1 1/8” Wood Screws Step 22 Attach Y20-LG and Y20-RG to SB1 Swing Beam using 5/16” x 2 ¾” Bolts and Lock washers on one side an
ITEMS NEEDED 4- Z5 Swing Hangers 4-Z1 Swing Hangers 2-Y25-G Glider Supports 4-X14 Glider Support Caps 4-Y28-G4 Bushings 1-X11 CAY Glider 2-X2-Y Swing Seats 4-A100015-38.5 Chains 4-Y60-51.25G Chains 2-Bags of Four ZQLB1 Quick Links HARDWARE NEEDED 2-5/16 x 5-3/4” Bolts 2-5/16 x 2 ½” Lag Screws 10-Fender Washers 10-5/16” Lock Nuts 4-Lock Washers for Bolts 4-Safety Washers Step 23 Attach four Z5 Swing Hangers and Safety Washers to Swing Beam with fender Washers and 5/16” Lock Nuts.
ITEMS NEEDED HARDWARE NEEDED 6-Y41 Ground Stakes 6-1/4 x 1 ¼” Phillip Truss Head Bolts 6-1/4” Barrel Nuts 12-Fender Washers 6-5/16” Lock Washers Step 24 Position playset in permanent location and secure to ground. Measure in 4" from Tower Legs and 4" from inside of K2 Base boards and mark ground. This should allow enough space to twist Stakes into ground using screwdriver for leverage. Now measure in 6” from outside H6 Swing Beam Ground Board and mark ground.
Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories.
Garantía limitada Esta garantía limitada de Backyard Discovery se aplica a productos fabricados bajo la marca Backyard Discovery o sus otras marcas incluyendo a título informativo pero no limitativo Backyard Botanical, Adventure Playsets, y Leisure Time Products. Backyard Discovery garantiza que este producto no tiene defectos de material ni de mano de obra durante el período de un (1) año a partir de la fecha original de compra.