WESTON Wooden Swing Set Model: # 65113 • Owner's Manual • Frequently Asked Questions • Assembly Instructions • Warranty Information Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetsonline.com (you will also find any updates on assembly instructions and information to order replacement parts) Features the fastening system.
STOP PARE Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com ¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA! La tienda donde realizó la compra no almacena piezas de este producto.
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing material washing away during heavy rains. 3.
Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth Wood Chips Double-Shredded bark mulch Engineered Wood Fibers Fine Sand Coarse Sand Fine Gravel Medium Gravel 6" (152mm) 7' (2.13m) 6' (1.83m) 6' (1.83m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 9" (228mm) 10' (3.05m) 10' (3.05m) 7' (2.13m) 5' (1.52m) 5' (1.52m) 7' (2.
Owner’s Manual Play Set 18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that they cannot be looped back on it. 19. Instruct children not to attach items to the playground equipment that are not specifically designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and chain as they may cause a strangulation hazard. 20. Instruct children to never wrap their legs around swing chain. 21.
Owner’s Manual Play Set Additional Maintenance: • Check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. • Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear. Light sand may be necessary to maintain a safe playing environment.
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 X3.
Owner’s Manual Play Set The American Society for Testing and Materials takes no position respecting the validity of any parent right asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such parent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Play Set Assembly Manual FAQs: 1. Does the area for the playset need to be level? Yes. Backyard Discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3.
www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the assembly manual and get the tools ready for the job as recommended in the manual. If the assembly manual is lost or misplaced a new one can be printed from Backyard Discovery’s website: www.swingsetsonline.com. 9. The playset seems to rock or sway too much. What’s wrong? Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground rails.
Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.
Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 13'-1 9/16" [4 m] 10'-10 3/16" [3.3 m] 6'-0" [1.8 m] 6'-0" [1.8 m] Safe Play Zone General Information: Your set has been designed and engineered for children only and for residential use only. A maximum of 150 lbs. per child is recommended for play activities designed for individual use.
Parts Identification Wood Components (NOT TO SCALE) E1 - UPRIGHT - W103800 (1) 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E2 - UPRIGHT - W103807 (1) 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E3 - UPRIGHT - W103809 (1) 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E4 - UPRIGHT - W103808 (1) 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E77 - ANGLE BRACE - W100991 (2) 1 3/8"x3 3/8"x74 3/8" (36x86x1890) F71 - STANDARD ANGLE BRACE - W100689 (4) 1 3/8"x2 3/8"x13" (36x60x330) H1 - FLOOR RAIL - W103804 (2) 1"x3 3/8"x30 3/4" (24x86x780) H2
Parts Identification Wood Components (NOT TO SCALE) H9 - HORIZONTAL TARP SUPPORT - W103818 (1) 1"x3 3/8"x54 3/4" (24x86x1392) H10 - SHELF SUPPORT - W103961 (2) 1"x3 3/8"x3 3/8" (24x86x86) H73 - ROCK WALL RAIL - W100024 (2) 24"x86"x1238" (24x86x1238) H79 - END SUPPORT - W100992 (1) 1"x3 1/2"x42" (24x86x1072) H80 - GROUND BOARD - W100990 (1) 1"x3 3/8"x87 3/8" (24x86x2218) K1 - GROUND BOARD - W103803 (2) 5/8"x5 1/4"x30" (16x134x762) K2 - ARCH BOARD - W103812 (2) 5/8"x5 1/4"x30" (16x134x762) K3 -
Parts Identification Wood Components (NOT TO SCALE) M2 - BENCH SEAT - W104043 (2) 5/8"x3 3/8"x24 3/8" (16x86x618) M3 - FLOOR BOARD - W103824 (7) 5/8"x3 3/8"x17 5/8" (16x86x448) M4 - FLOOR BOARD - W103823 (9) 5/8"x3 3/8"x22 3/8" (16x86x568) M5 - FLOOR RAIL - W103805 (1) 5/8"x3 3/8"x30" (16x86x762) M6 - FLOOR RAIL - W103806 (1) 5/8"x3 3/8"x30" (16x86x762) M7 - TOP TARP SUPPORT - W103820 (1) 5/8"x3 3/8"x30" (16x86x762) M8 - WALL RAIL - W103813 (3) 5/8"x3 3/8"x30 3/4" (16x86x780) M9 - FLOOR BOARD - W
Parts Identification Wood Components (NOT TO SCALE) M102 - ATTACHMENT BOARD - W103690 (1) 5/8"x3 3/8"x20 1/4" (16x86x514) N1 - WINDOW BOARD - W103828 (1) 5/8"x2 3/8"x21 1/2" (16x60x546) SB74 - SWING BEAM EXTENDED - W102419 (1) 2"x5 1/4"x89 1/2" (50x134x2274) W71 - SWING BEAM SUPPORT - W102420 (1) 2"x3 3/8"x49 5/8" (50x86x1260) (2) FP1 - FLOOR PANEL - W103821
Parts Identification Hardware (95) BR - SCREW PFH 8x1-1/8 - H100088 (84) BP - SCREW PFH 8x1-1/2 - H100086 (26) BS - SCREW PFH 8x1-3/4 - H100089 (2) BT - SCREW PFH 8x2-1/2 - H100090 (26) BW - SCREW PFH 8x3 - H100092 (2) - T-40 Torx Wrench - A100041 (13) CK - SCREW PFH 8x2 - H100111 (2) - T-30 Torx Wrench - H100114 (2) - T-40 Torx Bit - A100042 (70) AD - WASHER LOCK EXT 12x19 - H100031 (2) - T-30 Torx Bit - H100147 (91) AC - WASHER LOCK EXT 8x19 - H100030 (7) KW - WASHER LOCK EXT 8x15 - H100139 (
Parts Identification Hardware (11) CM - BOLT WH 5/16x1/2 - H100115 (7) F - BOLT WH 5/16x1 - H100008 (25) H - BOLT WH 5/16x1-1/2 - H100010 (13) B - NUT BARREL WH 5/16x5/8 - H100004 (60) D - NUT BARREL WH 5/16x7/8 - H100005 (2) C - NUT BARREL WH 5/16x1-1/2 - H100006 (6) J - BOLT WH 5/16x1-3/4 - H100011 (28) Z - LAG SCREW WH 5/16x2 - H100027 (21) K - BOLT WH 5/16x2 - H100012 (4) LC - LAG SCREW WH 1/4x1-1/2 - H100145 (2) L - BOLT WH 5/16x2-1/4 - H100013 (7) KS - NUT BARREL WH 1/4x5/8 - H100136 (7) M
Parts Identification Hardware (4) AJ - BOLT HEX 5/16x1 1/4 - H100042 (7) A - BOLT FA 3/8x1 1/2 - H100001 (16) CY - SCREW PWH 8x5/8 - H100128 (7) BF - T-NUT 3/8 - H100073 (8) BG - T-NUT 5/16 - H100074 (9) CJ - NUT LOCK 5/16 - H100110 (6) BZ - SWING HANGER QUICK LINK - H100099 (2) AN - BOLT HEX 5/16x2-3/4 - H100047
Parts Identification Accessories (NOT TO SCALE) (2) FB - SWING SEAT YELLOW - A100070 (6) FA - QUICK LINK - A100069 (2) ES - L BRACKET GREEN 32x51 - A100061 (1) HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 (2) GD - L BRACKET 66x66x127 - A100140 (1) TC - SWING BEAM EXTENSION BRACKET-RIGHT - A100326 (1) TB - SWING BEAM EXTENSION BRACKET-LEFT - A100325 (1) EM - SLIDE BED 8' YELLOW - A100056 (6) KC - METAL GROUND STAKE BROWN - A100178 (1) EK - SLIDE RAIL 8' GREEN RIGHT - A100054 (1) EL - SLIDE RAIL
Parts Identification Accessories (NOT TO SCALE) (2) EA - HAND GRIP YELLOW PLASTIC - A100043 (6) ER - CLIMBING ROCK GREEN SMALL - A100060 (1) - TRAPEZE - A6P00034 (1) WT - TARP .4x752x2309 - A100398 (2) KN - CHAIN GREEN 31" - A100177 (4) EZ - CHAIN GREEN 51.
(1) SB74 - SWING BEAM EXTENDED - W102419 2"x5 1/4"x89 1/2" (50x134x2274) (2) GD - L BRACKET 66x66x127 - A100140 (1) TC - SWING BEAM EXTENSION BRACKET-RIGHT - A100326 (1) TB - SWING BEAM EXTENSION BRACKET-LEFT - A100325 4 FT GREEN EXTENDED SWING BEAM WITH TRAPEZE STEP 1 GD ATTACH (2) GD BRACKETS TO SB74 SWING BEAM USING 2-3/4" BOLT, FLAT WASHERS AND 5/16" LOCK NUT, AS SHOWN. ATTACH TB AND TC SWING BEAM EXTENSION BRACKETS TO SB74 SWING BEAM USING 13/4" BOLTS AND 7/8" BARREL NUTS, AS SHOWN.
(1) W71 - SWING BEAM SUPPORT - W102420 2"x3 3/8"x49 5/8" (50x86x1260) (1) (2) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) (1) H79 - END SUPPORT - W100992 1"x3 1/2"x42" (24x86x1072) STEP 2 ATTACH H80 GROUND BOARD TO (2) E77 ANGLED SUPPORT BOARDS USING 2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS, AS SHOWN.
STEP 3 INSERT W71 BOARD INTO TB AND TC BRACKET OPENING AND SECURE USING 1-3/4" BOLTS AND 7/8" BARREL NUTS, AS SHOWN. (2) BOLT WH 5/16x1-3/4 (2) BOLT WH 5/16x2-1/2 INSERT 2-1/2" BOLTS, LOCK WASHERS AND 1-1/2" BARREL NUTS INTO THE EDGE OF W71 BOARD, AS SHOWN.
STEP 4 INSERT (6) SWING HANGER QUICK LINK INTO SB74 SWING BEAM USING SAFETY WASHERS, FLAT WASHERS AND 5/16" LOCK NUTS, AS SHOWN.
(6) M71 - ROCK BOARD - W100022 5/8"x3 3/8"x20 1/4" (16x86x514) (1) M72 - ROCK WALL SLAT - W100023 5/8"x3 3/8"x20 1/4" (16x86x514) (2) H73 - ROCK WALL RAIL - W100024 24"x86"x1238" (24x86x1238) 4' Rock Ladder Phase 1 Phase Notes • Assemble slats to rails as shown. • Note oreintation of slats, be sure to arrange as shown. • See drawing below for slat spacing on rails. • Using slats as a guide, pre-drill top edges of rails with a 1/8" drill bit. Failure to pre-drill may result in board splitting.
(6) ER - CLIMBING ROCK GREEN SMALL - A100060 4' Rock Ladder Phase Notes Phase 2 & 3 • Oreint top edge of rocks with top edge of slats. • Fasten rocks as shown.
8 FOOT SLIDE ASSEMBLY PHASE 1 STEP 1 TOP ● PLACE SLIDE BRACE CENTERED ON THE BOTTOM 1/4" FROM THE EDGE. TRANSFER HOLES ON THE BOARD THROUGH THE SLIDE BED AS SHOWN BELOW. USE A 3/8" DRILL BIT. ● ATTACH SLIDE BRACE TO SLIDE USING HARDWARE SHOWN. QTY 1 3 3 3 1 DESCRIPTION SLIDE BRACE BOLT WH 5/16x1/2 NUT BARREL WH 5/16x5/8 WASHER LOCK EXT 12x19 SLIDE BED 8' YELLOW (SEE SLIDE ASSEMBLY INSTALLATION STEP FOR TOP MOUNTING HOLE DRILLING LOCATIONS).
8 FOOT SLIDE ASSEMBLY PHASE 2 STEP 2 ● PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE SLIDE RAIL (FIG. 1). PUT SLIDE SUPPORT BOTTOM INTO THE SUPPORT POCKET AT THE BOTTOM OF THE RAIL AND HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT THE BED INTO THE SLIDE CAVITY. MAKE SURE SLIDE BED IS COMPLETELY DOWN IN THE SLIDE CAVITY. SECURE USING (12) 3" WOOD SCREWS AT EACH OF THE PILOT HOLE LOCATIONS AS SHOWN BELOW.
(1) (1) E1 - UPRIGHT - W103800 1 3/8"x3 3/8"x81 3/4" (36x86x2076) (1) E3 - UPRIGHT - W103809 1 3/8"x3 3/8"x81 3/4" (36x86x2076) H1 - FLOOR RAIL - W103804 1"x3 3/8"x30 3/4" (24x86x780) (1) (1) (1) K6 - DECORATIVE WALL BOARD - W103829 5/8"x5 1/4"x30 3/4" (16x134x780) K3 - GROUND BOARD - W103801 (1) K5 - WINDOW ARCH BOARD - W103811 5/8"x5 1/4"x30 3/4" (16x134x780) 5/8"x5 1/4"x30 3/4" (16x134x780) H3 - WALL RAIL - W103815 1"x3 3/8"x30 3/4" (24x86x780) (1) H8 - HORIZONTAL TARP SUPPORT - W103816 1"x3
(1) (1) E2 - UPRIGHT - W103807 1 3/8"x3 3/8"x81 3/4" (36x86x2076) (1) E4 - UPRIGHT - W103808 1 3/8"x3 3/8"x81 3/4" (36x86x2076) H1 - FLOOR RAIL - W103804 1"x3 3/8"x30 3/4" (24x86x780) (1) STEP 2 (1) (1) H9 - HORIZONTAL TARP SUPPORT - W103818 1"x3 3/8"x54 3/4" (24x86x1392) K4 - WALL RAIL - W103810 5/8"x5 1/4"x30 3/4" (16x134x780) H2 - SWING BEAM MOUNT - W103814 1"x3 3/8"x30 3/4" (24x86x780) (1) M8 - WALL RAIL - W103813 5/8"x3 3/8"x30 3/4" (16x86x780) (1) K8 - GROUND BOARD - W103802 5/8"x5 1/4
(2) K1 - GROUND BOARD - W103803 5/8"x5 1/4"x30" (16x134x762) STEP 3 E4 (8) (8) E2 E3 E1 K1 K1 WASHER LOCK EXT 8x19 (4 PLCS) LAG SCREW WH 5/16x2 (4 PLCS) LAG SCREW WH 5/16x2 (4 PLCS) WASHER LOCK EXT 8x19 (4 PLCS) LAG SCREW WH 5/16x2 WASHER LOCK EXT 8x19
(1) (1) K2 - ARCH BOARD - W103812 5/8"x5 1/4"x30" (16x134x762) M5 - FLOOR RAIL - W103805 5/8"x3 3/8"x30" (16x86x762) STEP 4 E4 (6) LAG SCREW WH 5/16x2 (6) E3 K2 E2 WASHER LOCK EXT 8x19 LAG SCREW WH 5/16x2 (4 PLCS) WASHER LOCK EXT 8x19 (4 PLCS) E1 LAG SCREW WH 5/16x2 (2 PLCS) M5 WASHER LOCK EXT 8x19 (2 PLCS)
(1) K2 - ARCH BOARD - W103812 5/8"x5 1/4"x30" (16x134x762) (1) M6 - FLOOR RAIL - W103806 5/8"x3 3/8"x30" (16x86x762) STEP 5 T-NUT 5/16 (2 PLCS) (6) LAG SCREW WH 5/16x2 (6) WASHER LOCK EXT 8x19 (2) T-NUT 5/16 M6 K2 LAG SCREW WH 5/16x2 (4 PLCS) WASHER LOCK EXT 8x19 (4 PLCS) M6 LAG SCREW WH 5/16x2 (2 PLCS) WASHER LOCK EXT 8x19 (2 PLCS) T-NUTS SHOULD FACE TOWARD THE OUTSIDE OF THE FORT.
(2) F71 - STANDARD ANGLE BRACE - W100689 1 3/8"x2 3/8"x13" (36x60x330) STEP 6 BOLT WH 5/16x1-1/2 (2) LAG SCREW WH 5/16x2 (2) WASHER LOCK EXT 12x19 (2) (4) NUT BARREL WH 5/16x7/8 (2) NUT BARREL WH 5/16x7/8 (2 PLCS) WASHER LOCK EXT 12x19 (2 PLCS) WASHER LOCK EXT 8x19 (2 PLCS) BOLT WH 5/16x1-1/2 (2 PLCS) F71 WASHER LOCK EXT 8x19 (2 PLCS) LAG SCREW WH 5/16x2 (2 PLCS) 11 9 12 10 13 11 14 12 15 13 E2 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 10 8 ! 19 20 22 21 17 18 20 19 16 18 15 17 13
(2) F71 - STANDARD ANGLE BRACE - W100689 1 3/8"x2 3/8"x13" (36x60x330) STEP 7 BOLT WH 5/16x2 (2) LAG SCREW WH 5/16x2 (2) WASHER LOCK EXT 8x19 (4) BOLT WH 5/16x2 (2 PLCS) WASHER LOCK EXT 8x19 (2 PLCS) F71 11 9 12 10 13 11 14 12 15 13 WASHER LOCK EXT 8x19 (2 PLCS) LAG SCREW WH 5/16x2 (2 PLCS) 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 10 8 ! 21 17 18 19 20 13 14 15 16 11 12 10 4 5 6 7 8 9 1 2 3 1 22 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3
(1) M9 - FLOOR BOARD - W103822 5/8"x3 3/8"x31 1/4" (16x86x794) (2) FP1 - FLOOR PANEL - W103821 STEP 8 (36) H1 FP1 M9 H1 M5 FP1 SCREW PFH 8x1-1/2 (36 PLCS) SCREW PFH 8x1-1/2
(7) M3 - FLOOR BOARD - W103824 5/8"x3 3/8"x17 5/8" (16x86x448) STEP 9 (28) INSIDE VIEW M3 SCREW PFH 8x1-1/8 (14 PLCS) SCREW PFH 8x1-1/8 (14 PLCS) K3 OUTSIDE VIEW USING A 1/8" DRILL BIT, DRILL DESIGNATED HOLES THROUGH 'M3' BOARDS.
(1) K7 - LEMONADE SHELF - W103825 5/8"x5 1/4"x27 7/8" (16x134x708) (2) H10 - SHELF SUPPORT - W103961 1"x3 3/8"x3 3/8" (24x86x86) STEP 10 (5) (2) SCREW PFH 8x2-1/2 (2 PLCS) SCREW PFH 8x1-1/2 (5 PLCS) K7 H10 SCREW PFH 8x2-1/2 SCREW PFH 8x1-1/2
(1) M8 - WALL RAIL - W103813 5/8"x3 3/8"x30 3/4" (16x86x780) (2) M11 - ANGLE BRACE - W103826 5/8"x3 3/8"x56 3/8" (16x86x1431) STEP 11 (2) (2) BOLT WH 5/16x2-1/4 (4) (4) NUT BARREL WH 5/16x7/8 (2 PLCS) WASHER LOCK EXT 12x19 (2 PLCS) (2) WASHER LOCK EXT 8x19 (2 PLCS) BOLT WH 5/16x2-1/4 (2 PLCS) NUT BARREL WH 5/16x7/8 M11 M11 NUT BARREL WH 5/16x5/8 (2 PLCS) BOLT WH 5/16x1 (2 PLCS) WASHER LOCK EXT 8x19 (2 PLCS) WASHER LOCK EXT 8x19 WASHER LOCK EXT 12x19 (2) M8 BOLT WH 5/16x1 WASHER LOCK EX
(7) M4 - FLOOR BOARD - W103823 5/8"x3 3/8"x22 3/8" (16x86x568) STEP 12 (28) SCREW PFH 8x1-1/8 (14 PLCS) SCREW PFH 8x1-1/8 (14 PLCS) 1 13/16" M4 REFERENCE VIEW SCREW PFH 8x1-1/8
(1) M8 - WALL RAIL - W103813 5/8"x3 3/8"x30 3/4" (16x86x780) STEP 13 (2) (2) BOLT WH 5/16x1-1/2 (2) (2) NUT BARREL WH 5/16x7/8 (2 PLCS) WASHER LOCK EXT 12x19 (2 PLCS) WASHER LOCK EXT 8x19 (2 PLCS) BOLT WH 5/16x1-1/2 (2 PLCS) M8 WASHER LOCK EXT 8x19 WASHER LOCK EXT 12x19 NUT BARREL WH 5/16x7/8
(2) M4 - FLOOR BOARD - W103823 5/8"x3 3/8"x22 3/8" (16x86x568) STEP 14 (8) M4 SCREW PFH 8x1-1/8 (4 PLCS) SCREW PFH 8x1-1/8 (4 PLCS) REFERENCE VIEW SCREW PFH 8x1-1/8
(5) M1 - WALL BOARD - W103827 5/8"x3 3/8"x13" (16x86x330) STEP 15 (10) M1 SCREW PFH 8x1 1/8 (10 PLCS) 1 13/16" REFERENCE VIEW SCREW PFH 8x1 1/8
(1) N1 - WINDOW BOARD - W103828 5/8"x2 3/8"x21 1/2" (16x60x546) STEP 16 (7) SCREW PFH 8x1-1/8 (7 PLCS) N1 FLUSH REFERENCE VIEW SCREW PFH 8x1-1/8
(2) M10 - END TARP SUPPORT - W103817 5/8"x3 3/8"x31 7/8" (16x86x810) STEP 17 SCREW PFH 8x2 (4 PLCS) (8) SCREW PFH 8x2 M10 M10 SCREW PFH 8x2 (4 PLCS)
(1) H7 - VERTICAL TARP SUPPORT - W103819 1"x3 3/8"x35 7/8" (24x86x910) STEP 18 (1) BOLT WH 5/16x1 BOLT WH 5/16x2 (1) (1) WASHER LOCK EXT 12x19 (2) WASHER LOCK EXT 8x19 (1 PLC) BOLT WH 5/16x2 (1 PLC) (1) H7 WASHER LOCK EXT 8x19 NUT BARREL WH 5/16x7/8 WASHER LOCK EXT 8x19 (1 PLC) BOLT WH 5/16x1 (1 PLC) WASHER LOCK EXT 12x19 (1 PLC) NUT BARREL WH 5/16x7/8 (1 PLC)
(1) H7 - VERTICAL TARP SUPPORT - W103819 1"x3 3/8"x35 7/8" (24x86x910) STEP 19 WASHER LOCK EXT 12x19 (1 PLC) (1) BOLT WH 5/16x1 (1) NUT BARREL WH 5/16x7/8 (1 PLC) (2) WASHER LOCK EXT 12x19 (2) H7 (2) BOLT WH 5/16x1-1/2 WASHER LOCK EXT 8x19 NUT BARREL WH 5/16x7/8 WASHER LOCK EXT 8x19 (1 PLC) BOLT WH 5/16x1-1/2 (1 PLC) BOLT WH 5/16x1 (1 PLC) WASHER LOCK EXT 8x19 (1 PLC) NUT BARREL WH 5/16x7/8 (1 PLC) WASHER LOCK EXT 12x19 (1 PLC)
(1) M7 - TOP TARP SUPPORT - W103820 5/8"x3 3/8"x30" (16x86x762) STEP 20 SCREW PFH 8x2 (4 PLCS) M7 (4) SCREW PFH 8x2
(1) WT - TARP .4x752x2309 - A100398 1/64"x29 5/8"x90 7/8" (.
(2) EA - HAND GRIP YELLOW PLASTIC - A100043 (1) SR - "B" REVISION TAG - A100315 STEP 22 (2) WASHER LOCK EXT 6x15 (4 PLCS) LAG SCREW WH 1/4x1-1/2 (4 PLCS) EA SR SCREW PWH 8x5/8 (2 PLCS) SCREW PWH 8x5/8 (4) LAG SCREW WH 1/4x1-1/2 (4) WASHER LOCK EXT 6x15
(1) M102 - ATTACHMENT BOARD - W103690 5/8"x3 3/8"x20 1/4" (16x86x514) (1) 4 FT ROCK LADDER STEP 23 WASHER LOCK EXT 12x19 (2 PLCS) NUT BARREL WH 5/16x5/8 (2 PLCS) M102 (4) SCREW PFH 8x1-1/2 (2) (2) WASHER LOCK EXT 12x19 (2) (2) SCREW PFH 8x1-1/2 (4 PLCS) BOLT WH 5/16x1 (2 PLCS) WASHER LOCK EXT 8x19 (2 PLCS) This rung may need to be temporarily removed to aid in rock ladder installation.
(1) 8 FT SLIDE ASSEMBLY STEP 24 6 5/16" 1 9/16" (3) WASHER LOCK EXT 12x19 (3) 4 3/16" BOLT WH 5/16x1/2 (3) 6 5/16" 1 5/16" NUT BARREL WH 5/16x5/8 DRILLING PATTERN BOLT WH 5/16x1/2 (3 PLCS) To prevent board splitting, you must pre-drill each board with a 7/16" drill bit, before attaching.
(1) 4 FT SWING BEAM ASSEMBLY (1) HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 STEP 25 (4) SCREW PWH 8x5/8 (4) (4) WASHER SPLIT 5/16 (4) BOLT HEX 5/16x1 1/4 (4 PLCS) WASHER SPLIT 5/16 (4 PLCS) WASHER FLAT 8x27 (4 PLCS) 4 FT SWING BEAM ASSEMBLY HC SCREW PWH 8x5/8 (4 PLCS) BOLT HEX 5/16x1 1/4 WASHER FLAT 8x27
(2) FB - SWING SEAT YELLOW - A100070 (6) FA - QUICK LINK - A100069 (2) KN - CHAIN GREEN 31" - A100177 (1) - TRAPEZE - A6P00034 (4) EZ - CHAIN GREEN 51.
(2) ES - L BRACKET GREEN 32x51 - A100061 (2) H6 - BENCH GROUND BOARD - W104042 1"x3 3/8"x18 1/8" (24x86x460) (2) H5 - BENCH UPRIGHT - W104041 1"x3 3/8"x11 3/4" (24x86x300) STEP 27 NUT BARREL WH 5/16x7/8 (2 PLCS) WASHER LOCK EXT 12x19 (2 PLCS) ES (2) BOLT WH 5/16x1/2 (2) WASHER LOCK EXT 12x19 (2) NUT BARREL WH 5/16x7/8 BOLT WH 5/16x1/2 (2 PLCS) ES H6 H6 STEP 28 H5 H5 (8) SCREW PFH 8x1-3/4 (4 PLCS) SCREW PFH 8x1-3/4 (4 PLCS) SCREW PFH 8x1-3/4
(2) H4 - BENCH SEAT SUPPORT - W104040 1"x3 3/8"x6 1/2" (24x86x166) (2) M2 - BENCH SEAT - W104043 5/8"x3 3/8"x24 3/8" (16x86x618) STEP 29 SCREW PFH 8x1-3/4 (4 PLCS) H4 SCREW PFH 8x1-3/4 (4 PLCS) H4 (8) SCREW PFH 8x1-3/4 (8) SCREW PFH 8x1-3/4 STEP 30 SCREW PFH 8x1-3/4 (4 PLCS) M2 M2 SCREW PFH 8x1-3/4 (4 PLCS)
(1) BENCH ASSEMBLY STEP 31 (2) (2) (2) BOLT WH 5/16x1/2 (2 PLCS) NUT BARREL WH 5/16x5/8 (2 PLCS) WASHER LOCK EXT 12x19 (2 PLCS) BOLT WH 5/16x1/2 WASHER LOCK EXT 12x19 NUT BARREL WH 5/16x5/8
(6) KC - METAL GROUND STAKE BROWN - A100178 Anchoring Instructions STEP 32 (4) BOLT WH 1/4x1/2" NOTE: (2) FAILURE TO USE GROUND STAKES CAN VOID WARRANTY & CAUSE INJURY! STAKE A (6) STAKE B WASHER FLAT 9x18 (6) STAKE A SWING BOLT WH 1/4x1 WASHER LOCK EXT 8x15 SWING (6) NUT BARREL WH 1/4x5/8 TRAPEZE STAKE A STAKE B STAKE A STAKE B WASHER LOCK EXT 8x15 (2 PLCS) STAKE A NUT BARREL WH 1/4x5/8 (2 PLCS) WASHER LOCK EXT 8x15 (4 PLCS) NUT BARREL WH 1/4x5/8 (4 PLCS) BOLT WH 1/4x1 (2 PLCS) WASHER
Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories.
