PRAIRIE RIDGE Wooden Swing Set Model: # • Owner's Manual • Frequently Asked Questions • Assembly Instructions • Warranty Information Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetsonline.com (you will also find any updates on assembly instructions and information to order replacement parts) Features the fastening system.
STOP Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing material washing away during heavy rains. 3.
Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth Wood Chips Double-Shredded bark mulch Engineered Wood Fibers Fine Sand Coarse Sand Fine Gravel Medium Gravel 6" (152mm) 7' (2.13m) 6' (1.83m) 6' (1.83m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 9" (228mm) 10' (3.05m) 10' (3.05m) 7' (2.13m) 5' (1.52m) 5' (1.52m) 7' (2.
Owner’s Manual Play Set 18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that they cannot be looped back on it. 19. Instruct children not to attach items to the playground equipment that are not specifically designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and chain as they may cause a strangulation hazard. 20. Instruct children to never wrap their legs around swing chain. 21.
Owner’s Manual Play Set Additional Maintenance: • Check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. • Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear. Light sand may be necessary to maintain a safe playing environment.
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. ; 6(&7,21 2) 7+( &21680(5 352'8&7 6$)(7< &200,66,21·6 287'225 +20( 3/$<*5281' 6$)(7< +$1'%22.
Owner’s Manual Play Set 7KH $PHULFDQ 6RFLHW\ IRU 7HVWLQJ DQG 0DWHULDOV WDNHV QR SRVLWLRQ UHVSHFWLQJ WKH YDOLGLW\ RI DQ\ SDUHQW ULJKW DVVHUWHG LQ FRQQHFWLRQ ZLWK DQ\ LWHP PHQWLRQHG LQ WKLV VWDQGDUG 8VHUV RI WKLV VWDQGDUG DUH H[SUHVVO\ DGYLVHG WKDW GHWHUPLQDWLRQ RI WKH YDOLGLW\ RI DQ\ VXFK SDUHQW ULJKWV DQG WKH ULVN RI LQIULQJHPHQW RI VXFK ULJKWV DUH HQWLUHO\ WKHLU RZQ UHVSRQVLELOLW\ 7KH VWDQGDUG LV VXEMHFW WR UHYLVLRQ DW DQ\ WLPH E\ WKH UHVSRQVLEOH WHFKQLFDO FRPPLWWHH DQG PXVW EH UHYLHZHG HYHU\
Play Set Assembly Manual FAQs: 1. Does the area for the playset need to be level? Yes. Backyard Discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3.
www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the assembly manual and get the tools ready for the job as recommended in the manual. If the assembly manual is lost or misplaced a new one can be printed from Backyard Discovery’s website: www.swingsetsonline.com. 9. The playset seems to rock or sway too much. What’s wrong? Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground rails.
Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.
Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.
Parts Identification Wood Components (NOT TO SCALE) E1 - UPRIGHT - W101261 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E2 - UPRIGHT - W103773 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E3 - UPRIGHT - W101256 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E71 - MONKEY BAR RAIL - W102369 1 3/8"x3 3/8"x60 5/8" (36x86x1539) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) E78 - MONKEY BAR UPRIGHT - W100975 1 3/8"x3 3/8"x74 3/4" (36x86x1900) F71 - STANDARD ANGLE BRACE - W100689 1 3/8"x2 3/8"x13" (36x
Parts Identification Wood Components (NOT TO SCALE) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) H81 - MONKEY BAR BRACE - W100993 1"x3 3/8"x53 1/4" (24x86x1352) H82 - MONKEY BAR GROUND BOARD - W100994 1"x3 3/8"x70 3/8" (24x86x1786) J1 - WINDOW LEDGE - W100709 1"x2 3/8"x29 1/2" (24x60x750) J2 - END FLOOR CLEAT - W100710 1"x2 3/8"x3 3/8" (24x60x86) J3 - FLOOR JOIST - W100984 1"x2 3/8"x60 1/8" (24x60x1528) K1 - ROOF SWING BEAM SUPPORT - W100682 5/8"x5 1/4"x51 5/8" (16x1
Parts Identification Wood Components (NOT TO SCALE) K9-4 - WALL BOARD - W101239 3/8"x3 3/8"x37 3/8" (11x86x950) K9-5 - WALL BOARD - W101259 3/8"x3 3/8"x21 3/8" (11x86x544) K9-3 - WALL BOARD - W101257 3/8"x3 3/8"x42" (11x86x1068) L2 - GROUND BOARD - W100684 5/8"x4 3/8"x60 1/8" (16x112x1528) L3 - GROUND BOARD - W101602 5/8"x4 3/8"x46 7/8" (16x112x1191) L5 - GROUND BOARD - W100686 5/8"x4 3/8"x30" (16x112x762) L6 - ARCHED RAIL - W100694 5/8"x4 3/8"x60 1/8" (16x112x1528) L7 - ARCH
Parts Identification Wood Components (NOT TO SCALE) M4 - TARP TOP SUPPORT - W100693 5/8"x3 3/8"x60 1/8" (16x86x1528) M6 - LOWER FACE BOARD - W101598 5/8"x3 3/8"x38 5/8" (16x86x982) M7 - WALL BOARD - W100708 5/8"x3 3/8"x35 1/4" (16x86x895) M8 - WALL RAIL - W100700 5/8"x3 3/8"x35 7/8" (16x86x910) M9 - ANGLE BRACE - W100696 5/8"x3 3/8"x35 5/8" (16x86x904) M10 - SAFETY BOARD - W100701 5/8"x3 3/8"x33 7/8" (16x86x860) M11 - UPPER FACE BOARD - W102866 5/8"x3 3/8"x26 5/8" (16x86x67
Parts Identification Wood Components (NOT TO SCALE) M17 - PICKET - W100705 5/8"x3 3/8"x27 1/8" (16x86x690) M18 - PICKET - W103761 5/8"x3 3/8"x18 7/8" (16x86x480) M71 - ROCK BOARD - W100022 5/8"x3 3/8"x20 1/4" (16x86x514) M72 - ROCK WALL SLAT - W100023 5/8"x3 3/8"x20 1/4" (16x86x514) M16 - TARP SUPPORT - W101237 5/8"x3 3/8"x29 1/8" (16x86x740) M77 - SLIDE BRACE - W100544 5/8"x3 3/8"x17 1/4" (16x86x438) M78 - CENTER SLIDE BRACE - W100545 5/8"x3 3/8"x17 1/4" (16x86x438) SB
Parts Identification Hardware (36) Z - LAG SCREW WH 5/16x2 - H100027 (18) B - NUT BARREL WH 5/16x5/8 - H100004 (13) AA - LAG SCREW WH 5/16x2 1/2 - H100028 (45) D - NUT BARREL WH 5/16x7/8 - H100005 (10) F - BOLT WH 5/16x1 - H100008 (2) C - NUT BARREL WH 5/16x1 1/2 - H100006 (2) G - BOLT WH 5/16x1 1/4 - H100009 (4) AG - BOLT HEX 5/16x1 - H100040 (39) H - BOLT WH 5/16x1 1/2 - H100010 (4) AN - BOLT HEX 5/16x2-3/4 - H100047 (6) J - BOLT WH 5/16x1 3/4 - H100011 (7) BE - T-NUT 1/4 - H100072 (13) K - BOLT WH
Parts Identification Hardware (4) LC - LAG SCREW WH 1/4x1-1/2 - H100145 (4) BX - WASHER SPLIT 5/16 - H100095 (7) AY - BOLT PTH 1/4x1 - H100061 (11) CG - WASHER LOCK INT 8x15 - H100108 (15) CH - SCREW TAPPING 14x1-1/2 - H100109 (19) CE - WASHER FLAT 9x18 - H100106 (61) BN - SCREW PFH 8x1 - H100085 (44) BR - SCREW PFH 8x1 1/8 - H100088 (22) CD - WASHER FLAT 8x27 - H100105 (24) BQ - SCREW PFH 8x1 1/4 - H100087 (160) BP - SCREW PFH 8x1 1/2 - H100086 (4) CB - WASHER SAFETY 17x30 - H100103 (28) BS - SCREW
Parts Identification Hardware (4) KY - BOLT WH 1/4x1/2" - H100141 (13) CM - BOLT WH 5/16x1/2 - H100115 (2) - T-40 Torx Wrench - A100041 (9) KS - NUT BARREL WH 1/4x5/8 - H100136 (4) KT - BOLT WH 1/4x1 - H100137 (7) A - BOLT FA 3/8x1 1/2 - H100001 (4) BZ - SWING HANGER QUICK LINK - H100099 (7) CY - SCREW PWH 8x5/8 - H100128 (4) BY - SWING HANGER QUICK LINK - H100097 (2) - T-30 Torx Wrench - H100114 (13) CT - SCREW TAPPING 8x1/2 - H100123 (9) KW - WASHER LOCK EXT 8x15 - H100139 (15) CJ - NUT LOCK
Parts Identification Accessories (NOT TO SCALE) (1) DN - GLIDER SEAT DARK GREEN - A100025 (2) DO - CAPTAINS GLIDER ARM YELLOW - A100026 (6) EA - HAND GRIP YELLOW PLASTIC - A100043 (6) EC - METAL RUNG 559 - A100045 (6) ER - CLIMBING ROCK GREEN SMALL - A100060 (4) EJ - L BRACKET 54x67 - A100053 (1) EM - SLIDE BED 8' YELLOW - A100056 (1) EL - SLIDE RAIL 8' GREEN LEFT - A100055 (1) EK - SLIDE RAIL 8' GREEN RIGHT - A100054 (1) HY - TARP 1522x2119 - A100062
3DUWV ,GHQWLILFDWLRQ $FFHVVRULHV (NOT TO SCALE) (1) HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 (1) TC - SWING BEAM EXTENSION BRACKET-RIGHT - A100326 (2) EW - GLIDER SUPPORT BYD GREEN - A100065 (4) EX - GLIDER BUSHING BYD GREEN - A100066 (1) TB - SWING BEAM EXTENSION BRACKET-LEFT - A100325 (4) EY - TUBING CAP GLIDER SUPPORT - A100067 (2) QZ - TRIANGLE PLATE 100° 5 HOLE - A100294 (2) GD - L BRACKET 66x66x127 - A100140 (2) FB - SWING SEAT YELLOW - A100070 (8) FA - QUICK LINK - A100069 (4) EZ - CHAI
5RFN /DGGHU 3KDVH 3KDVH 1RWHV • Assemble slats to rails as shown. • Note oreintation of slats, be sure to arrange as shown. • See drawing below for slat spacing on rails. • Using slats as a guide, pre-drill top edges of rails with a 1/8" drill bit. Failure to pre-drill may result in board splitting. SCREW PFH 8x1-1/2 723 0 0 THESE SURFACES FLUSH BOTH SIDES + PRE-DRILL TOP EDGE OF RAILS QTY.
5RFN /DGGHU 3KDVH 3KDVH 1RWHV • Oreint top edge of rocks with top edge of slats. • Fasten rocks as shown. BOLT FA 3/8x1-1/2 CLIMBING ROCK GREEN SMALL T-NUT 3/8 QTY. DESCRIPTION 6 CLIMBING ROCK GREEN SMALL 6 BOLT FA 3/8x1-1/2 6 T-NUT 3/8 SCREW PFH 8x1-1/8 QTY.
SB74 - SWING BEAM EXTENDED - W102419 2"x5 1/4"x89 1/2" (50x134x2274) GD - L BRACKET 66x66x127 - A100140 TC - SWING BEAM EXTENSION BRACKET-RIGHT - A100326 TB - SWING BEAM EXTENSION BRACKET-LEFT - A100325 4 FT GREEN EXTENDED SWING BEAM WITH GLIDER (3) STEP 1 ATTACH (2) GD BRACKETS TO SB74 SWING BEAM USING (2) 2-3/4" BOLTS, FLAT WASHERS AND 5/16" LOCK NUT, AS SHOWN.
W71 - SWING BEAM SUPPORT - W102420 2"x3 3/8"x49 5/8" (50x86x1260) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) H79 - END SUPPORT - W100992 1"x3 1/2"x42" (24x86x1072) STEP 2 ATTACH H80 GROUND BOARD TO (2) E77 ANGLED SUPPORT BOARDS USING (2) 2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS, AS SHOWN. (4) ATTACH (2) E77 ANGLED SUPPORT BOARDS TO W71 SUPPORT USING 4- 1/2" BOLT, LOCK WASHERS AND 7/8" BARREL NUT, AS SHOWN.
STEP 3 INSERT W71 BOARD INTO TB AND TC BRACKET OPENING AND SECURE USING (2) 1-3/4" BOLTS AND 7/8" BARREL NUTS, AS SHOWN. INSERT (2) 2-1/2" BOLTS, LOCK WASHERS AND 1-1/2" BARREL NUTS INTO THE EDGE OF W71 BOARD, AS SHOWN. (2) (2) BOLT WH 5/16x1-3/4 (2) BOLT WH 5/16x2-1/2 NUT BARREL WH 5/16x7/8 NUT BARREL (2) WH 5/16x1-1/2 WASHER WASHER (2) LOCK EXT (2) LOCK EXT 12x19 8x19 6% 7% 7& : THESE BOLTS ARE REQUIRED FOR IMPROVED STRUCTUAL STRENGHT OF W71 SUPPORT AND MUST BE INSTALLED.
EY - TUBING CAP GLIDER SUPPORT - A100067 EX - GLIDER BUSHING BYD GREEN - A100066 EW - GLIDER SUPPORT BYD GREEN - A100065 STEP 4 ATTACH (2) EW GLIDER SUPPORT BARS TO SB74 SWING BEAM USING (2) 5-3/4" BOLTS, FLAT WASHERS AND 5/16" LOCK NUTS AND (2) 2-1/2" LAG SCREWS, AS SHOWN. INSERT (4) SWING HANGER QUICK LINKS INTO (4) EX BUSHINGS AND THEN ATTACH SWING HANGER QUICK LINKS TO EW GLIDER SUPPORTS USING (4) FLAT WASHERS AND 5/16" LOCK NUTS, AS SHOWN.
STEP 5 INSERT (4) SWING HANGER QUICK LINK INTO SB74 SWING BEAM USING (4) SAFETY WASHERS, FLAT WASHERS AND 5/16" LOCK NUTS, AS SHOWN.
8 FOOT SLIDE ASSEMBLY PHASE 1 STEP 1 723 Ɣ PLACE SLIDE BRACE CENTERED ON THE BOTTOM 1/4" FROM THE EDGE. TRANSFER HOLES ON THE BOARD THROUGH THE SLIDE BED AS SHOWN BELOW. USE A 3/8" DRILL BIT. Ɣ ATTACH SLIDE BRACE TO SLIDE USING HARDWARE SHOWN. QTY 1 3 3 3 1 DESCRIPTION SLIDE BRACE BOLT WH 5/16x1/2 NUT BARREL WH 5/16x5/8 WASHER LOCK EXT 12x19 SLIDE BED 8' YELLOW (SEE SLIDE ASSEMBLY INSTALLATION STEP FOR TOP MOUNTING HOLE DRILLING LOCATIONS).
8 FOOT SLIDE ASSEMBLY PHASE 2 STEP 2 Ɣ PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE SLIDE RAIL (FIG. 1). PUT SLIDE SUPPORT BOTTOM INTO THE SUPPORT POCKET AT THE BOTTOM OF THE RAIL AND HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT THE BED INTO THE SLIDE CAVITY. MAKE SURE SLIDE BED IS COMPLETELY DOWN IN THE SLIDE CAVITY. SECURE USING (12) 3" WOOD SCREWS AT EACH OF THE PILOT HOLE LOCATIONS AS SHOWN BELOW.
E71 - MONKEY BAR RAIL - W102369 1 3/8"x3 3/8"x60 5/8" (36x86x1539) EJ - L BRACKET 54x67 - A100053 QZ - TRIANGLE PLATE 100 5 HOLE - A100294 MONKEY BAR ASSEMBLY STEP 1 (2) YOU WILL BUILD A LEFT AND RIGHT TOP RAIL IN THIS STEP. BOLT WH 5/16x1 BOLT WH 5/16x1-1/2 (6) AFTER BUILDING LEFT ASSEMBLY AS SHOWN, REPEAT STEPS FOR A RIGHT ASSEMBLY. SEE BELOW FOR OREINTATION OF RIGHT SIDE TRIANGLE PLATE. (2) WASHER LOCK EXT 12x19 ASSEMBLE WITH HARDWARE AS SHOWN.
E78 - MONKEY BAR UPRIGHT - W102370 1 3/8"x3 3/8"x74 3/4" (36x86x1900) MONKEY BAR ASSEMBLY STEP 2 ASSEMBLE WITH HARDWARE AS SHOWN. REPEAT PROCESS FOR OTHER SIDE OF MONKEY BAR ASSEMBLY.
EC - METAL RUNG 559 - A100045 MONKEY BAR ASSEMBLY STEP 3 ASSEMBLE AS SHOWN INTO PRE-DRILLED HOLES.
H81 - MONKEY BAR BRACE - W100993 1"x3 3/8"x53 1/4" (24x86x1352) H82 - MONKEY BAR GROUND BOARD - W100994 1"x3 3/8"x70 3/8" (24x86x1786) MONKEY BAR ASSEMBLY (4) LAG SCREW WH 5/16x2 (2) BOLT HEX 5/16x2-3/4 (2) WASHER LOCK INT 8x15 (8) WASHER LOCK EXT 8x19 (2) WASHER FLAT 9x18 (4) WASHER LOCK EXT 12x19 (2) T-NUT 5/16 NUT BARREL (4)WH 5/16x7/8 (4) STEP 4 ASSEMBLE AS SHOWN.
EA - HAND GRIP YELLOW PLASTIC - A100043 MONKEY BAR ASSEMBLY LAG SCREW (4)WH 1/4x1-1/2 (4) STEP 5 ASSEMBLE WITH HARDWARE AS SHOWN.
E2 - UPRIGHT - W103773 1 3/8"x3 3/8"x81 3/4" (36x86x2076) M5 - FACE BOARD - W101599 5/8"x3 3/8"x43 1/8" (16x86x1094) STEP 1 ATTACH M5 BOARDS TO E2 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. NOTE THE ORIENTATION OF THE HOLES WITH THE E2 BOARDS.
E3 - UPRIGHT - W101256 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E1 - UPRIGHT - W101261 1 3/8"x3 3/8"x81 3/4" (36x86x2076) M6 - LOWER FACE BOARD - W101598 5/8"x3 3/8"x38 5/8" (16x86x982) L5 - GROUND BOARD - W100686 5/8"x4 3/8"x30" (16x112x762) STEP 2 ATTACH THE M6 BOARDS AND THE L5 BOARD TO THE E3 AND E1 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. NOTE THE ORIENTATION OF THE E3 AND E1 BOARDS.
L2 - GROUND BOARD - W100684 5/8"x4 3/8"x60 1/8" (16x112x1528) STEP 3 (8) ATTACH THE L2 BOARDS TO THE E1, E3 AND E2 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
L3 - GROUND BOARD - W101602 5/8"x4 3/8"x46 7/8" (16x112x1191) M9 - ANGLE BRACE - W100696 5/8"x3 3/8"x35 5/8" (16x86x904) M10 - SAFETY BOARD - W100701 5/8"x3 3/8"x33 7/8" (16x86x860) STEP 4 ATTACH M10 AND L3 BOARDS TO THE M5 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. (2) NUT BARREL WH 5/16x5/8 ATTACH M9 BOARD TO THE M10 AND THE L3 BOARD USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
K4 - FLOOR RAIL - W103700 5/8"x5 1/4"x60 1/8" (16x134x1528) M13 - FLOOR RAIL - W103774 5/8"x3 3/8"x60 1/8" (16x86x1528) STEP 5 ATTACH M13 BOARD TO THE E1 BOARD AND THE E2 BOARD USING HARDWARE SHOWN THROUGH PRE DRILLED HOLES. NOTE THE ORIENTATION OF HOLES THAT WILL BE USED LATER IN THE M13 BOARD. (8) BOLT WH 5/16x2 ATTACH K4 BOARD TO E3 BOARD AND E2 BOARD USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. BOLT WH 5/16x2 3/&6 T-NUT 5/16 3/&6 WASHER LOCK EXT 8x19 3/&6 ( ( ( 0 ( .
M14 - FLOOR SUPPORT BOARD - W103944 5/8"x3 3/8"x30" (16x86x762) K5 - FLOOR RAIL - W103768 5/8"x5 1/4"x30" (16x134x762) STEP 6 ATTACH K5 BOARD TO E2 BOARDS AND ATTACH M14 BOARD TO E1 AND E3 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES (6) LAG SCREW WH 5/16x2 WASHER LOCK EXT 8x19 3/&6 (6) WASHER LOCK EXT 8x19 LAG SCREW WH 5/16x2 3/&6 ( .
SP1 - FLOOR SUPPORT CLEAT - W100711 1"x1"x53 3/8" (24x24x1356) F71 - STANDARD ANGLE BRACE - W100689 1 3/8"x2 3/8"x13" (36x60x330) J2 - END FLOOR CLEAT - W100710 1"x2 3/8"x3 3/8" (24x60x86) STEP 7 FIRST ATTACH A F71 BRACE TO A M13 BOARD AND A F71 BRACE TO A K4 BOARD USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLE. (2) NUT BARREL WH 5/16x7/8 PRE DRILL AND ATTACH THE F71 BRACES TO E2 BOARDS. (2) ATTACH A SP1 BOARD TO M13 BOARD AND K4 BOARD RESTING ON F71 BRACES.
F71 - STANDARD ANGLE BRACE - W100689 1 3/8"x2 3/8"x13" (36x60x330) J3 - FLOOR JOIST - W100984 1"x2 3/8"x60 1/8" (24x60x1528) STEP 8 ATTACH F71 BRACES TO K5 AND M14 BOARDS THROUGH PRE DRILLED HOLES WITH HARDWARE AS SHOWN (4) NUT BARREL WH 5/16x7/8 (4) PRE DRILL E1, E3, AND E2 BRACES AND FASTEN F71 BOARDS TO THEM WITH HARDWARE AS SHOWN ATTACH J3 FLOOR JOIST TO M14 AND K5 BOARDS WITH BOTTOM OF J3 JOIST BEING 3/8" FROM BOTTOM OF M14 AND K5 BOARDS WITH HARDWARE SHOWN THROUGH PRE DRILLED HOLES.
L9 - END FLOOR BOARD - W102863 5/8"x4 3/8"x29 7/8" (16x112x760) STEP 9 PLACE L9 BOARDS ON THE J3 FLOOR JOIST AND J2 SUPPORT BOARDS. L9 BOARD WILL SIT UP AGAINST THE E2 BOARDS AND THE E3 AND E1 BOARD AS SHOWN. ATTACH L9 BOARDS TO J2 BOARDS AND J3 FLOOR JOIST THROUGH PRE DRILLED HOLES. (10) SCREW PFH 8x1 1/2 SCREW PFH 8x1 1/2 3/&6 / .
(3) FP1 - FLOOR PANEL - W102861 STEP 10 ATTACH FP1 FLOOR PANELS TO SP1 BOARDS AND J3 FLOOR JOIST USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. (45) SCREW PFH 8x1 1/2 (45 PLCS) )3 63 )3 .
M12 - MONKEY BAR ARCH BOARD - W103775 5/8"x3 3/8"x30" (16x86x762) M11 - UPPER FACE BOARD - W102866 5/8"x3 3/8"x26 5/8" (16x86x676) STEP 11 ATTACH 1/4" T-NUTS TO M11 BOARDS AS SHOWN. ATTACH M11 BOARDS TO E1 BOARD AND E3 BOARD WITH HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
L6 - ARCHED RAIL - W100694 5/8"x4 3/8"x60 1/8" (16x112x1528) L7 - ARCHED SCULPTURED RAIL - W100695 5/8"x4 3/8"x60 1/8" (16x112x1528) STEP 12 ATTACH L6 BOARD AS SHOWN TO E1 AND E2 BOARDS THROUGH PRE DRILLED HOLES USING HARDWARE AS SHOWN. (8) NUT BARREL WH 5/16x7/8 (8) BOLT WH 5/16x1 1/2 ATTACH L7 BOARD AS SHOWN TO E3 AND E2 BOARDS THROUGH PRE DRILLED HOLES USING HARDWARE AS SHOWN.
K1 - ROOF SWING BEAM SUPPORT - W100682 5/8"x5 1/4"x51 5/8" (16x134x1310) K2 - ROOF SUPPORT - W100683 5/8"x5 1/4"x51 5/8" (16x134x1310) STEP 13 ATTACH 5/16 T NUTS TO K1 BOARD AS SHOWN AND ATTACH TO E2 BOARDS THROUGH PRE DRILLED HOLES WITH HARDWARE AS SHOWN. ATTACH K2 BOARD TO E1, AND E3 BOARDS WITH HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. (8) WASHER LOCK EXT 8x19 3/&6 LAG SCREW WH 5/16x2 3/&6 . ( T-NUT 5/16 3/&6 .
M1 - PICKET RAIL - W103760 5/8"x3 3/8"x30" (16x86x762) M18 - PICKET - W103761 5/8"x3 3/8"x18 7/8" (16x86x480) STEP 14 ATTACH M1 BOARD TO E2 BOARDS AS SHOWN. ATTACH M18 PICKETS TO M1 BOARD AND K5 BOARD USING SPACING AS SHOWN (16) (2) ( 0 ( 0 SCREW PFH 8x1 1/8 LAG SCREW WH 5/16x2 (2) WASHER LOCK EXT 8x19 WASHER LOCK EXT 8x19 3/&6 LAG SCREW WH 5/16x2 3/&6 .
M8 - WALL RAIL - W100700 5/8"x3 3/8"x35 7/8" (16x86x910) M7 - WALL BOARD - W100708 5/8"x3 3/8"x35 1/4" (16x86x895) STEP 15 ATTACH M7 BOARD TO L6 BOARD AND M13 BOARD THROUGH PRE DRILLED HOLES USING HARDWARE AS SHOWN. (2) ATTACH M8 BOARD TO M7 BOARD AND E1 BOARD USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
M17 - PICKET - W100705 5/8"x3 3/8"x27 1/8" (16x86x690) STEP 16 ATTACH M17 PICKETS TO L6 AND M8 BOARDS USING SPACING AND HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
K9-2 - WALL BOARD - W100712 3/8"x3 3/8"x30 1/4" (11x86x768) K9-1 - WALL BOARD - W100713 3/8"x3 3/8"x15 3/4" (11x86x400) J1 - WINDOW LEDGE - W100709 1"x2 3/8"x29 1/2" (24x60x750) STEP 17 PLACE (2) K9-2 BOARDS ON FLOOR AGAINST L7 AND K4 BOARDS, AND AGAINST E3 BOARD LIP OF K9-2 TOUCHING E3 BOARD AND ATTACH WITH HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. (28) ATTACH K9-1 BOARDS AND (2) K9-2 BOARDS L7 AND K4 BOARD AGAINST PREVIOUSLY ATTACHED K9-2 BOARDS.
M3 - TARP SUPPORT - W100692 5/8"x3 3/8"x60 1/8" (16x86x1528) STEP 18 ATTACH M3 BOARDS TO K1 AND K2 BOARDS THROUGH PRE DRILLED HOLES USING HARDWARE AS SHOWN. SCREW PFH 8x2 3/&6 (8) 0 . .
M16 - TARP SUPPORT - W101237 5/8"x3 3/8"x29 1/8" (16x86x740) M4 - TARP TOP SUPPORT - W100693 5/8"x3 3/8"x60 1/8" (16x86x1528) STEP 19 ATTACH M16 BOARDS AS SHOWN TO K1 AND K2 BOARDS. (2) ATTACH M4 BOARD FLUSH TO M16 BOARDS AS SHOWN. (4) SCREW PFH 8x2 SCREW PFH 8x2 3/&6 (2) (2) 0 . NUT BARREL WH 5/16x5/8 BOLT WH 5/16x1 1/4 (4) WASHER LOCK EXT 8x19 (2) WASHER LOCK EXT 12x19 0 0 BOLT WH 5/16x1 .
HY - TARP 1522x2119 - A100062 1/32"x59 7/8"x83 3/8" (.4x1522x2119) STEP 20 CENTER HY TARP OVER M4 TARP TOP SUPPORT AND ATTACH USING (4) 1/2" TAPPING SCREWS, AS SHOWN. NEXT, DRAPE HY TARP EVENLY OVER (2) M3 TARP SUPPORTS AND WRAP UNDERNEATH AND UP THE BACK SIDE OF M3 SUPPORT APPROXIMATELY 1-13/16" FROM THE TOP AND ATTACH USING (8) 1/2" TAPPING SCREWS, AS SHOWN.
K9-3 - WALL BOARD - W101257 3/8"x3 3/8"x42" (11x86x1068) K9-4 - WALL BOARD - W101239 3/8"x3 3/8"x37 3/8" (11x86x950) L8 - SCULPTURED RAIL - W101240 5/8"x4 3/8"x35 1/2" (16x112x902) K9-5 - WALL BOARD - W101259 3/8"x3 3/8"x21 3/8" (11x86x544) STEP 21 ATTACH L8 BOARD TO E3 BOARD FLUSH WITH THE UNDERSIDE OF K4 BOARD USING HARDWARE AS SHOWN FIG. 1. (1) NUT BARREL WH 5/16x5/8 (1) STARTING AGAINST E3 BOARD, ATTACH A K9-3 BOARD FLUSH WITH THE BOTTOM OF THE SP1 BOARD USING HARDWARE AS SHOWN.
H3 - SERVING BOARD SUPPORT - W101606 1"x3 3/8"x3 3/8" (24x86x86) H1 - SERVING SHELF SUPPORT - W101604 1"x3 3/8"x30 3/4" (24x86x780) K3 - SERVING BOARD - W101605 5/8"x5 1/4"x28 3/4" (16x134x729) STEP 22 ATTACH H3 SHELF SUPPORTS TO K3 AND H1 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. .
EA - HAND GRIP YELLOW PLASTIC - A100043 STEP 24 ATTACH EA HANDLE TO E2 BOARD USING HARDWARE AS SHOWN (FIG. 1). INSERT 1/4" T-NUTS INTO M7 BOARD AND ATTACH EA HANDLE AS SHOWN (FIG. 2). (6) ATTACH 2 EA HANDLES TO M11 BOARDS USING PREVIOUSLY INSERTED T-NUTS.
M2 - BENCH SEAT - W104044 5/8"x3 3/8"x27 3/8" (16x86x694) H5 - BENCH UPRIGHT - W104041 1"x3 3/8"x11 3/4" (24x86x300) H4 - BENCH SEAT SUPPORT - W104040 1"x3 3/8"x6 1/2" (24x86x166) H6 - BENCH GROUND BOARD - W104042 1"x3 3/8"x18 1/8" (24x86x460) STEP 25 EJ - L BRACKET 54x67 - A100053 NUT BARREL WH 5/16x7/8 3/&6 ATTACH (2) EJ BRACKETS TO H6 BENCH GROUND BOARDS USING (2) 1/2" BOLT, LOCK WASHERS AND 7/8" BARREL NUT, AS SHOWN.
(1) - BENCH ASSEMBLY STEP 26 USING BENCH ASSEMBLY BRACKETS AS A TEMPLATE, DRILL TWO 3/8" THRU HOLES AND ATTACH EJ BRACKET TO L2 GROUND BOARD USING (2) 1/2" BOLTS, LOCK WASHERS AND 5/8" BARREL NUTS, AS SHOWN.
(1) - SLIDE ASSEMBLY STEP 27 CENTER THE WAVE SLIDE ASSEMBLY IN OPENING, AS SHOWN. USING A 3/8" DRILL BIT, DRILL THREE THROUGH HOLES INTO THE SLIDE BED AND DECK BOARDS, AS SHOWN BELOW. (3) BOLT WH 5/16x1/2 (3) WASHER LOCK EXT 12x19 ATTACH THE SLIDE ASSEMBLY TO THE DECK USING (3) 1/2" BOLTS, LOCK WASHERS AND 5/8" BARREL NUTS, AS SHOWN.
(1) - ROCK LADDER ASSEMBLY STEP 28 CENTER LADDER ON 'M13' BOARD AND PILOT DRILL 3/16" HOLES FOR LADDER ATTACHMENT. ATTACH THE ROCK LADDER ASSEMBLY TO M13 FLOOR RAIL SUPPORT USING (2) 2-1/2" LAG SCREWS AND LOCK WASHERS, AS SHOWN.
(1) - SWING BEAM ASSEMBLY HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 STEP 29 ATTACH SWING BEAM ASSEMBLY TO K1 ROOF SWING BEAM SUPPORT USING (4) 1" BOLTS, SPLIT WASHERS AND FLAT WASHERS, AS SHOWN BELOW. ATTACH HC I.D. TAG TO SB74 SWING BEAM USING (4) 5/8" PFH SCREWS, AS SHOWN.
(1) - MONKEY BAR ASSEMBLY STEP 30 ATTACH MONKEY BAR ASSEMBLY TO M12 ARCH BOARD USING HARDWARE AS SHOWN.
EZ - CHAIN GREEN 51.25" - A100068 JD - CHAIN GREEN 45" - A100092 FB - SWING SEAT YELLOW - A100070 DN - GLIDER SEAT DARK GREEN - A100025 DO - CAPTAINS GLIDER ARM YELLOW - A100026 STEP 31 ATTACH FB SWING SEAT TO (2) EZ CHAINS USING (2) FA QUICK LINKS, AS SHOWN. REPEAT PROCESS TO ASSEMBLE SECOND SWING ASSEMBLY. NOW, ATTACH EZ CHAINS TO SWING HANGER QUICK LINKS ALREADY ASSEMBLED TO THE SWING BEAM.
KC - METAL GROUND STAKE BROWN - A100178 SR - "B" REVISION TAG - A100315 Anchoring Instructions STAKE A (4) STAKE A NOTE: BOLT WH 1/4x1/2" BOLT WH 1/4x1 (4) FAILURE TO USE GROUND STAKES CAN VOID WARRANTY & CAUSE INJURY! (8) STAKE A WASHER LOCK EXT 8x15 WASHER FLAT 9x18 (8) (8) NUT BARREL WH 1/4x5/8 (2) SCREW PWH 8x5/8 STAKE B STAKE B STAKE B STEP 32 TWIST STAKES INTO GROUND AGAINST GROUND BOARDS WHERE SHOWN. ATTACH GROUND BOARD USING (2) 1" BOLTS, WASHERS AND BARREL NUTS.
Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories.
