PRAIRIE RIDGE Wooden Swing Set Model: 55006 •• •• •• •• Owner's Manual Frequently Asked Questions Assembly Instructions Warranty Information Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetsonline.com (you will also find any updates on assembly instructions and information to order replacement parts) Features the fastening system.
STOP PARE Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com ¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA! La tienda donde realizó la compra no almacena piezas de este producto.
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing material washing away during heavy rains. 3.
Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth Wood Chips Double-Shredded bark mulch Engineered Wood Fibers Fine Sand Coarse Sand Fine Gravel Medium Gravel 6" (152mm) 7' (2.13m) 6' (1.83m) 6' (1.83m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 9" (228mm) 10' (3.05m) 10' (3.05m) 7' (2.13m) 5' (1.52m) 5' (1.52m) 7' (2.
Owner’s Manual Play Set 18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that they cannot be looped back on it. 19. Instruct children not to attach items to the playground equipment that are not specifically designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and chain as they may cause a strangulation hazard. 20. Instruct children to never wrap their legs around swing chain. 21.
Owner’s Manual Play Set Additional Maintenance: • Check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. • Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear. Light sand may be necessary to maintain a safe playing environment.
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 X3.
Owner’s Manual Play Set The American Society for Testing and Materials takes no position respecting the validity of any parent right asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such parent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Play Set Assembly Manual FAQs: 1. Does the area for the playset need to be level? Yes. Backyard Discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3.
www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the assembly manual and get the tools ready for the job as recommended in the manual. If the assembly manual is lost or misplaced a new one can be printed from Backyard Discovery’s website: www.swingsetsonline.com. 9. The playset seems to rock or sway too much. What’s wrong? Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground rails.
Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.
Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 21'-9 3/4" [6.6] 10'-9 3/16" [3.3] 6'-0" [1.8] Safe Play Zone 6'-0" [1.8] General Information: Your set has been designed and engineered for children only and for residential use only. A maximum of 150 lbs. per child is recommended for play activities designed for individual use. A maximum of 120 lbs.
Parts Identification Wood Components (NOT TO SCALE) E1 - UPRIGHT - W101261 (1) 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E2 - UPRIGHT - W101260 (2) 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E3 - UPRIGHT - W101256 (1) 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E4 - MONKEY BAR TOP - W103945 (2) 1 3/8"x3 3/8"x71 3/8" (36x86x1814) E5 - MONKEY BAR ANGLE BRACES - W103948 (2) 1 3/8"x3 3/8"x54 1/2" (36x86x1385) E6 - MONKEY BAR UPRIGHTS - W103946 (2) 1 3/8"x3 3/8"x82 7/8" (36x86x2105) E77 - ANGLE BRACE - W100991 (2) 1 3/8"x3 3
Parts Identification Wood Components (NOT TO SCALE) H74 - LEFT UPRIGHT - W100608 (1) 1"x3 3/8"x50 3/4" (24x86x1290) H75 - RIGHT UPRIGHT - W100609 (1) 1"x3 3/8"x50 3/4" (24x86x1290) H76 - LADDER RUNG - W100611 (4) 1"x3 3/8"x18 1/8" (24x86x460) H79 - END SUPPORT - W100992 (1) 1"x3 1/2"x42" (24x86x1072) H80 - GROUND BOARD - W100990 (1) 1"x3 3/8"x87 3/8" (24x86x2218) J1 - WINDOW LEDGE - W103951 (1) 1"x2 3/8"x22" (24x60x560) J2 - END FLOOR CLEAT - W100710 (4) 1"x2 3/8"x3 3/8" (24x60x86) J3 - FLOOR
Parts Identification Wood Components (NOT TO SCALE) K9-4 - WALL BOARD - W101239 (2) 3/8"x3 3/8"x37 3/8" (11x86x950) K9-5 - WALL BOARD - W101259 (6) 3/8"x3 3/8"x21 3/8" (11x86x544) L1 - FLOOR RAIL - W101254 (1) 5/8"x4 3/8"x60 1/8" (16x112x1528) L2 - GROUND BOARD - W100684 (2) 5/8"x4 3/8"x60 1/8" (16x112x1528) L3 - GROUND BOARD - W101602 (1) 5/8"x4 3/8"x46 7/8" (16x112x1191) L4 - FLOOR RAIL - W101603 (1) 5/8"x4 3/8"x30" (16x112x762) L5 - GROUND BOARD - W100686 (1) 5/8"x4 3/8"x30" (16x112x762) L6
Parts Identification Wood Components (NOT TO SCALE) M4 - TARP TOP SUPPORT - W100693 (1) 5/8"x3 3/8"x60 1/8" (16x86x1528) M5 - FACE BOARD - W101599 (2) 5/8"x3 3/8"x43 1/8" (16x86x1094) M6 - LOWER FACE BOARD - W101598 (2) 5/8"x3 3/8"x38 5/8" (16x86x982) M7 - WALL BOARD - W100708 (1) 5/8"x3 3/8"x35 1/4" (16x86x895) M8 - WALL RAIL - W100700 (1) 5/8"x3 3/8"x35 7/8" (16x86x910) M9 - ANGLE BRACE - W100696 (1) 5/8"x3 3/8"x35 5/8" (16x86x904) M10 - SAFETY BOARD - W100701 (1) 5/8"x3 3/8"x33 7/8" (16x86x
Parts Identification Wood Components (NOT TO SCALE) M16 - TARP SUPPORT - W101237 (1) 5/8"x3 3/8"x29 1/8" (16x86x740) M17 - PICKET - W100705 (4) 5/8"x3 3/8"x27 1/8" (16x86x690) M73 - REAR SUPPORT - W100610 (1) 5/8"x3 3/8"x19 1/4" (16x86x488) M77 - SLIDE BRACE - W100544 (1) 5/8"x3 3/8"x17 1/4" (16x86x438) M78 - CENTER SLIDE BRACE - W100545 (2) 5/8"x3 3/8"x17 1/4" (16x86x438) SB74 - SWING BEAM EXTENDED - W102419 (1) 2"x5 1/4"x89 1/2" (50x134x2274) SP1 - FLOOR SUPPORT CLEAT - W100711 (2) 1"x1"x53 3/
Parts Identification Hardware (17) B - NUT BARREL WH 5/16x5/8 - H100004 (30) Z - LAG SCREW WH 5/16x2 - H100027 (38) D - NUT BARREL WH 5/16x7/8 - H100005 (2) C - NUT BARREL WH 5/16x1 1/2 - H100006 (13) AA - LAG SCREW WH 5/16x2 1/2 - H100028 (8) F - BOLT WH 5/16x1 - H100008 (4) BB - LAG SCREW HEX 5/16x2 - H100067 (3) G - BOLT WH 5/16x1 1/4 - H100009 (2) - LAG SCREW HEX 5/16x2-1/2 - H100068 (25) H - BOLT WH 5/16x1 1/2 - H100010 (2) NZ - BOLT HEX 5/16x3 - H100048 (6) J - BOLT WH 5/16x1 3/4 - H100011 (
Parts Identification Hardware (29) BG - T-NUT 5/16 - H100074 (4) BX - WASHER SPLIT 5/16 - H100095 (7) BE - T-NUT 1/4 - H100072 (41) CG - WASHER LOCK INT 8x15 - H100108 (7) AY - BOLT PTH 1/4x1 - H100061 (30) CC - WASHER FLAT 8x19 - H100104 (7) CH - SCREW TAPPING 14x1-1/2 - H100109 (61) BN - SCREW PFH 8x1 - H100085 (22) CE - WASHER FLAT 9x18 - H100106 (50) BR - SCREW PFH 8x1 1/8 - H100088 (22) CD - WASHER FLAT 8x27 - H100105 (24) BQ - SCREW PFH 8x1 1/4 - H100087 (124) BP - SCREW PFH 8x1 1/2 - H10008
Parts Identification (4) KY - BOLT WH 1/4x1/2" - H100141 (9) KS - NUT BARREL WH 1/4x5/8 - H100136 (4) KT - BOLT WH 1/4x1 - H100137 (2) - T-30 Torx Wrench - H100114 (15) CM - BOLT WH 5/16x1/2 - H100115 (4) BZ - SWING HANGER QUICK LINK - H100099 (7) CY - SCREW PWH 8x5/8 - H100128 (4) BY - SWING HANGER QUICK LINK - H100097 (13) CT - SCREW TAPPING 8x1/2 - H100123 (2) - T-40 Torx Wrench - A100041 Hardware (2) - BOLT HEX 5/16x3-1/4 - H100050 (2) - T-30 Torx Bit - H100147 (9) KW - WASHER LOCK EXT 8x1
Parts Identification Accessories (NOT TO SCALE) (1) DN - GLIDER SEAT DARK GREEN - A100025 (2) DO - CAPTAINS GLIDER ARM YELLOW - A100026 (6) EA - HAND GRIP YELLOW PLASTIC - A100043 (5) EC - METAL RUNG 559 - A100045 (2) EJ - L BRACKET 54x67 - A100053 (4) XK - SQUARE ANGLE BRACKET - A100413 (1) EM - SLIDE BED 8' YELLOW - A100056 (1) HY - TARP 1522x2119 - A100062 (1) EL - SLIDE RAIL 8' GREEN LEFT - A100055 (1) EK - SLIDE RAIL 8' GREEN RIGHT - A100054
Parts Identification Accessories (NOT TO SCALE) (1) HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 (1) TC - SWING BEAM EXTENSION BRACKET-RIGHT - A100326 (2) EW - GLIDER SUPPORT BYD GREEN - A100065 (4) EX - GLIDER BUSHING BYD GREEN - A100066 (1) TB - SWING BEAM EXTENSION BRACKET-LEFT - A100325 (4) EY - TUBING CAP GLIDER SUPPORT - A100067 (2) XF - TRIANGLE PLATE - A100411 (2) GD - L BRACKET 66x66x127 - A100140 (4) XH - MONKEY BAR LADDER RUNG - A100412 (2) FB - SWING SEAT YELLOW - A100070 (4) EZ - CH
4 Ft Ladder Phase 1 & 2 Phase Notes • Assemble with hardware as shown. • Center rungs in rail grooves.
4 Ft Ladder Phase 3 Phase Notes • Assemble with hardware as shown.
(1) SB74 - SWING BEAM EXTENDED - W102419 2"x5 1/4"x89 1/2" (50x134x2274) (2) GD - L BRACKET 66x66x127 - A100140 (1) TC - SWING BEAM EXTENSION BRACKET-RIGHT - A100326 (1) TB - SWING BEAM EXTENSION BRACKET-LEFT - A100325 4 FT GREEN EXTENDED SWING BEAM WITH GLIDER (3) STEP 1 ATTACH (2) GD BRACKETS TO SB74 SWING BEAM USING (2) 2-3/4" BOLTS, FLAT WASHERS AND 5/16" LOCK NUT, AS SHOWN.
(1) W71 - SWING BEAM SUPPORT - W102420 2"x3 3/8"x49 5/8" (50x86x1260) (1) (2) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (1) H79 - END SUPPORT - W100992 1"x3 1/2"x42" (24x86x1072) STEP 2 ATTACH H80 GROUND BOARD TO (2) E77 ANGLED SUPPORT BOARDS USING (2) 2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS, AS SHOWN.
STEP 3 INSERT W71 BOARD INTO TB AND TC BRACKET OPENING AND SECURE USING (2) 1-3/4" BOLTS AND 7/8" BARREL NUTS, AS SHOWN. INSERT (2) 2-1/2" BOLTS, LOCK WASHERS AND 1-1/2" BARREL NUTS INTO THE EDGE OF W71 BOARD, AS SHOWN.
(4) EY - TUBING CAP GLIDER SUPPORT - A100067 (4) EX - GLIDER BUSHING BYD GREEN - A100066 (2) EW - GLIDER SUPPORT BYD GREEN - A100065 STEP 4 USING EW GLIDER SUPPORTS AS A GUIDE, USE A 3/16" TO PRE DRILL HOLES INTO SB74 SWING BEAM. ATTACH (2) EW GLIDER SUPPORT BARS TO SB74 SWING BEAM USING (2) 5-3/4" BOLTS, FLAT WASHERS AND 5/16" LOCK NUTS AND (2) 2-1/2" LAG SCREWS, AS SHOWN.
STEP 5 INSERT (4) SWING HANGER QUICK LINK INTO SB74 SWING BEAM USING (4) SAFETY WASHERS, FLAT WASHERS AND 5/16" LOCK NUTS, AS SHOWN.
(2) E4 - MONKEY BAR TOP - W103945 1 3/8"x3 3/8"x71 3/8" (36x86x1814) (4) XK - SQUARE ANGLE BRACKET - A100413 (5) EC - METAL RUNG 559 - A100045 (2) XF - TRIANGLE PLATE - A100411 STEP 1 LAY TWO E4 MONKEY BAR TOP FLAT ON GROUND. (10) ATTACH EC RUNGS TO E4 MONKEY BAR BOARDS JOINT CONNECTOR 5/16 X 2-1/2 E4 EC (10) (10) WASHER FLAT 8x19 WASHER LOCK INT 8x15 E4 STEP 2 ATTACH XF BRACKETS TO OUTSIDE OF E4 BOARDS, AND XK BRACKETS TO INSIDE AND OUTSIDE OF E4 BOARDS AS SHOWN.
(2) E6 - MONKEY BAR UPRIGHTS - W103946 1 3/8"x3 3/8"x82 7/8" (36x86x2105) (4) XH - MONKEY BAR LADDER RUNG - A100412 STEP 3 TAP XH LADDER RUNGS INTO E6 BOARDS USING A RUBBER MALLET OR HAMMER AND A BLOCK.
(1) G1 - MONKEY BAR GROUND BOARD - W103947 1"x5 1/4"x79 1/2" (24x134x2020) STEP 4 USING G1 AS A GUIDE PRE DRILL 3/16" HOLES IN CENTER OF E6 BOARDS. ATTACH G1 GROUND BOARD TO E6 BOARDS AS SHOWN.
(2) E5 - MONKEY BAR ANGLE BRACES - W103948 1 3/8"x3 3/8"x54 1/2" (36x86x1385) STEP 5 USING G1 BOARD AS A GUIDE DRILL (2) 3/16" HOLES IN EACH E5 BOARD. ATTACH (2) E5 BOARDS TO E6 AND G1 BOARDS AS SHOWN.
TOP ASSEMBLY LADDER ASSEMBLY STEP 6 ATTACH E4 BOARDS TO E6 BOARDS USING XF TRIANGLE BRACE AS SHOWN.
(2) EA - HAND GRIP YELLOW PLASTIC - A100043 STEP 7 PRE DRILL WITH 1/8" BIT AND ATTACH EA HAND GRIPS AS SHOWN.
8 FOOT SLIDE ASSEMBLY PHASE 1 STEP 1 TOP ● PLACE SLIDE BRACE CENTERED ON THE BOTTOM 1/4" FROM THE EDGE. TRANSFER HOLES ON THE BOARD THROUGH THE SLIDE BED AS SHOWN BELOW. USE A 3/8" DRILL BIT. ● ATTACH SLIDE BRACE TO SLIDE USING HARDWARE SHOWN. QTY 1 3 3 3 1 DESCRIPTION SLIDE BRACE BOLT WH 5/16x1/2 NUT BARREL WH 5/16x5/8 WASHER LOCK EXT 12x19 SLIDE BED 8' YELLOW (SEE SLIDE ASSEMBLY INSTALLATION STEP FOR TOP MOUNTING HOLE DRILLING LOCATIONS).
8 FOOT SLIDE ASSEMBLY PHASE 2 STEP 2 ● PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE SLIDE RAIL (FIG. 1). PUT SLIDE SUPPORT BOTTOM INTO THE SUPPORT POCKET AT THE BOTTOM OF THE RAIL AND HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT THE BED INTO THE SLIDE CAVITY. MAKE SURE SLIDE BED IS COMPLETELY DOWN IN THE SLIDE CAVITY. SECURE USING (12) 3" WOOD SCREWS AT EACH OF THE PILOT HOLE LOCATIONS AS SHOWN BELOW.
(2) E2 - UPRIGHT - W101260 1 3/8"x3 3/8"x81 3/4" (36x86x2076) (2) M5 - FACE BOARD - W101599 5/8"x3 3/8"x43 1/8" (16x86x1094) STEP 1 ATTACH E2 BOARDS TO M5 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. NOTE THE ORIENTATION OF THE HOLES WITH THE E2 BOARDS.
(1) E3 - UPRIGHT - W101256 1 3/8"x3 3/8"x81 3/4" (36x86x2076) (1) E1 - UPRIGHT - W101261 1 3/8"x3 3/8"x81 3/4" (36x86x2076) (2) M6 - LOWER FACE BOARD - W101598 5/8"x3 3/8"x38 5/8" (16x86x982) (1) L5 - GROUND BOARD - W100686 5/8"x4 3/8"x30" (16x112x762) STEP 2 ATTACH THE L5 BOARDS AND THE M6 BOARD TO THE E3 AND E1 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. NOTE THE ORIENTATION OF THE E3 AND E1 BOARDS.
(2) L2 - GROUND BOARD - W100684 5/8"x4 3/8"x60 1/8" (16x112x1528) STEP 3 (8) ATTACH THE L2 BOARDS TO THE E1, E3 AND E2 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(1) L3 - GROUND BOARD - W101602 5/8"x4 3/8"x46 7/8" (16x112x1191) (1) M9 - ANGLE BRACE - W100696 5/8"x3 3/8"x35 5/8" (16x86x904) (1) M10 - SAFETY BOARD - W100701 5/8"x3 3/8"x33 7/8" (16x86x860) STEP 4 ATTACH M10 AND L3 BOARDS TO THE M5 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. (2) NUT BARREL WH 5/16x5/8 ATTACH M9 BOARD TO THE M10 AND THE L3 BOARD USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(1) L1 - FLOOR RAIL - W101254 5/8"x4 3/8"x60 1/8" (16x112x1528) (1) M13 - FLOOR RAIL - W102867 5/8"x3 3/8"x60 1/8" (16x86x1528) STEP 5 ATTACH M13 BOARD TO THE E1 BOARD AND THE E2 BOARD USING HARDWARE SHOWN THROUGH PRE DRILLED HOLES. NOTE THE ORIENTATION OF HOLES THAT WILL BE USED LATER IN THE M13 BOARD. ATTACH L1 BOARD TO E3 BOARD AND E2 BOARD USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(1) M14 - FLOOR SUPPORT BOARD - W103944 5/8"x3 3/8"x30" (16x86x762) (1) L4 - FLOOR RAIL - W101603 5/8"x4 3/8"x30" (16x112x762) STEP 6 ATTACH L4 BOARD TO E2 BOARDS AND ATTACH M14 BOARD TO E1 AND E3 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(2) SP1 - FLOOR SUPPORT CLEAT - W100711 1"x1"x53 3/8" (24x24x1356) (2) (4) F71 - STANDARD ANGLE BRACE - W100689 1 3/8"x2 3/8"x13" (36x60x330) J2 - END FLOOR CLEAT - W100710 1"x2 3/8"x3 3/8" (24x60x86) STEP 7 FIRST ATTACH A F71 BRACE TO A M13 BOARD AND A F71 BRACE TO A L1 BOARD USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLE. (2) NUT BARREL WH 5/16x7/8 PRE DRILL WITH 3/16" BIT AND ATTACH THE F71 BRACES TO E2 BOARDS. (2) ATTACH A SP1 BOARD TO M13 BOARD AND L1 BOARD RESTING ON F71 BRACES.
(4) F71 - STANDARD ANGLE BRACE - W100689 1 3/8"x2 3/8"x13" (36x60x330) (1) J3 - FLOOR JOIST - W100984 1"x2 3/8"x60 1/8" (24x60x1528) STEP 8 ATTACH F71 BRACES TO L4 AND M14 BOARDS THROUGH PRE DRILLED HOLES WITH HARDWARE AS SHOWN (4) NUT BARREL WH 5/16x7/8 (4) BOLT WH 5/16x1 1/2 PRE DRILL E1, E3, AND E2 UPRIGHTS AND FASTEN F71 BRACES TO THEM WITH HARDWARE AS SHOWN ATTACH J3 FLOOR JOIST TO M14 AND L4 BOARDS WITH BOTTOM OF J3 JOIST BEING 3/8" FROM BOTTOM OF M14 AND L4 BOARDS WITH HARDWARE SHOWN THROUGH
(2) L9 - END FLOOR BOARD - W102863 5/8"x4 3/8"x29 7/8" (16x112x760) STEP 9 PLACE L9 BOARDS ON THE J3 FLOOR JOIST AND J2 SUPPORT BOARDS. L9 BOARD WILL SIT UP AGAINST THE E2 BOARDS AND THE E3 AND E1 BOARD AS SHOWN. ATTACH L9 BOARDS TO J2 BOARDS AND J3 FLOOR JOIST THROUGH PRE DRILLED HOLES.
(3) FP1 - FLOOR PANEL - W102861 STEP 10 ATTACH FP1 FLOOR PANELS TO SP1 BOARDS AND J3 FLOOR JOIST USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(1) M12 - ROCK WALL ARCH BOARD - W102862 5/8"x3 3/8"x30" (16x86x762) (2) M11 - UPPER FACE BOARD - W102866 5/8"x3 3/8"x26 5/8" (16x86x676) STEP 11 ATTACH 1/4" T-NUTS TO M12 BOARDS AS SHOWN. ATTACH M11 BOARDS TO E1 BOARD AND E3 BOARD WITH HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(1) L6 - ARCHED RAIL - W100694 5/8"x4 3/8"x60 1/8" (16x112x1528) (1) L7 - ARCHED SCULPTURED RAIL - W100695 5/8"x4 3/8"x60 1/8" (16x112x1528) STEP 12 ATTACH L6 BOARD AS SHOWN TO E1 AND E2 BOARDS THROUGH PRE DRILLED HOLES USING HARDWARE AS SHOWN. (8) ATTACH L7 BOARD AS SHOWN TO E3 AND E2 BOARDS THROUGH PRE DRILLED HOLES USING HARDWARE AS SHOWN.
(1) K1 - ROOF SWING BEAM SUPPORT - W100682 5/8"x5 1/4"x51 5/8" (16x134x1310) (1) K2 - ROOF SUPPORT - W103949 5/8"x5 1/4"x51 5/8" (16x134x1310) STEP 13 ATTACH 5/16 T NUTS TO K1 BOARD AS SHOWN AND ATTACH TO E2 BOARDS THROUGH PRE DRILLED HOLES WITH HARDWARE AS SHOWN. ATTACH K2 BOARD TO E1, E2, AND E3 BOARDS WITH HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(1) M1 - TENT SUPPORT - W101601 5/8"x3 3/8"x59 1/4" (16x86x1504) (2) WP1 - FLOOR PANEL - W102865 STEP 14 ATTACH M1 BOARD TO K1 AND L4 BOARDS AS SHOWN. ATTACH WP1 WALL PANELS TO M1, K1 AND L4 BOARDS AS SHOWN.
(1) M8 - WALL RAIL - W100700 5/8"x3 3/8"x35 7/8" (16x86x910) (1) M7 - WALL BOARD - W100708 5/8"x3 3/8"x35 1/4" (16x86x895) STEP 15 ATTACH M7 BOARD TO L6 BOARD AND M13 BOARD THROUGH PRE DRILLED HOLES USING HARDWARE AS SHOWN. (2) NUT BARREL WH 5/16x5/8 ATTACH M8 BOARD TO M7 BOARD AND E1 BOARD USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(4) M17 - PICKET - W100705 5/8"x3 3/8"x27 1/8" (16x86x690) STEP 16 ATTACH M17 PICKETS TO L6 AND M8 BOARDS USING SPACING AND HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(4) K9-2 - WALL BOARD - W103950 3/8"x3 3/8"x30 1/4" (11x86x768) (6) (1) K9-1 - WALL BOARD - W100713 3/8"x3 3/8"x15 3/4" (11x86x400) J1 - WINDOW LEDGE - W100709 1"x2 3/8"x29 1/2" (24x60x750) STEP 17 PLACE 2 K9-2 BOARDS ON FLOOR AGAINST L7 AND K4 BOARDS, AND AGAINST E3 BOARD LIP OF K9-2 TOUCHING E3 BOARD AND ATTACH WITH HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES. ATTACH (6) K9-1 BOARDS AND THE OTHER (2) K9-2 BOARDS L7 AND K4 BOARD AGAINST PREVIOUSLY ATTACHED K9-2 BOARDS.
(2) M3 - TARP SUPPORT - W100692 5/8"x3 3/8"x60 1/8" (16x86x1528) STEP 18 ATTACH M3 BOARDS TO K1 AND K2 BOARDS THROUGH PRE DRILLED HOLES USING HARDWARE AS SHOWN.
(1) M16 - TARP SUPPORT - W101237 5/8"x3 3/8"x29 1/8" (16x86x740) (1) M4 - TARP TOP SUPPORT - W100693 5/8"x3 3/8"x60 1/8" (16x86x1528) STEP 19 ATTACH M16 BOARD AS SHOWN TO K2 BOARD. (4) SCREW PFH 8x2 (2) NUT BARREL WH 5/16x5/8 (2) BOLT WH 5/16x1 (2) WASHER LOCK EXT 8x19 (2) WASHER LOCK EXT 12x19 ATTACH M4 BOARD FLUSH TO TOP OF M1 AND M16 BOARDS AS SHOWN.
(1) HY - TARP 1522x2119 - A100062 1/32"x59 7/8"x83 3/8" (.4x1522x2119) STEP 20 CENTER HY TARP OVER M4 TARP TOP SUPPORT AND ATTACH USING (4) 1/2" TAPPING SCREWS, AS SHOWN. NEXT, DRAPE HY TARP EVENLY OVER (2) M3 TARP SUPPORTS AND WRAP UNDERNEATH AND UP THE BACK SIDE OF M3 SUPPORT APPROXIMATELY 1-13/16" FROM THE TOP AND ATTACH USING (8) 1/2" TAPPING SCREWS, AS SHOWN.
(2) K9-3 - WALL BOARD - W101257 3/8"x3 3/8"x42" (11x86x1068) (2) K9-4 - WALL BOARD - W101239 3/8"x3 3/8"x37 3/8" (11x86x950) (1) (6) L8 - SCULPTURED RAIL - W101240 5/8"x4 3/8"x35 1/2" (16x112x902) K9-5 - WALL BOARD - W101259 3/8"x3 3/8"x21 3/8" (11x86x544) STEP 21 ATTACH L8 BOARD TO E3 BOARD FLUSH WITH THE UNDERSIDE OF L1 BOARD USING HARDWARE AS SHOWN FIG. 1. (1) STARTING AGAINST E3 BOARD, ATTACH A K9-3 BOARD FLUSH WITH THE BOTTOM OF THE SP1 BOARD USING HARDWARE AS SHOWN.
(2) H3 - SERVING BOARD SUPPORT - W101606 1"x3 3/8"x3 3/8" (24x86x86) (1) H1 - SERVING SHELF SUPPORT - W101604 1"x3 3/8"x30 3/4" (24x86x780) (1) K3 - SERVING BOARD - W101605 5/8"x5 1/4"x28 3/4" (16x134x729) STEP 22 ATTACH H3 SHELF SUPPORTS TO K3 AND H1 BOARDS USING HARDWARE AS SHOWN THROUGH PRE DRILLED HOLES.
(4) EA - HAND GRIP YELLOW PLASTIC - A100043 STEP 24 ATTACH EA HANDLE TO E2 BOARD USING HARDWARE AS SHOWN (FIG. 1). INSERT 1/4" T-NUTS INTO M7 BOARD AND ATTACH EA HANDLE AS SHOWN (FIG. 2). (6) BOLT PTH 1/4x1 (2) ATTACH 2 EA HANDLES TO M11 BOARDS USING PREVIOUSLY INSERTED T-NUTS. (2) M7 SCREW TAPPING 14x1-1/2 T-NUT 1/4 (8) WASHER FLAT 9x18 (8) WASHER LOCK INT 8x15 E2 M11 M11 EA 8" T-NUT 1/4 (2 PLCS) BOLT PTH 1/4x1 (6 PLCS) FIG. 2 FIG.
(2) M2 - BENCH SEAT - W102469 5/8"x3 3/8"x27 3/8" (16x86x694) (2) H4 - BENCH SEAT SUPPORT - W102470 1"x3 3/8"x6 1/2" (24x86x166) (2) EJ - L BRACKET 54x67 - A100053 H5 - BENCH UPRIGHT - W102471 (2) 1"x3 3/8"x11 3/4" (24x86x300) (2) H6 - BENCH GROUND BOARD - W102472 1"x3 3/8"x18 1/8" (24x86x460) STEP 27 ATTACH (2) EJ BRACKETS TO H6 BENCH GROUND BOARDS USING (2) 1/2" BOLT, LOCK WASHERS AND 7/8" BARREL NUT, AS SHOWN.
(1) - BENCH ASSEMBLY STEP 26 USING BENCH ASSEMBLY BRACKETS AS A TEMPLATE, DRILL TWO 3/8" THRU HOLES AND ATTACH EJ BRACKET TO L2 GROUND BOARD USING (2) 1/2" BOLTS, LOCK WASHERS AND 5/8" BARREL NUTS, AS SHOWN.
(1) - SLIDE ASSEMBLY STEP 27 CENTER THE WAVE SLIDE ASSEMBLY IN OPENING, AS SHOWN. USING A 3/8" DRILL BIT, DRILL THREE THROUGH HOLES INTO THE SLIDE BED AND DECK BOARDS, AS SHOWN BELOW. (3) BOLT WH 5/16x1/2 (3) WASHER LOCK EXT 12x19 ATTACH THE SLIDE ASSEMBLY TO THE DECK USING (3) 1/2" BOLTS, LOCK WASHERS AND 5/8" BARREL NUTS, AS SHOWN.
(1) - LADDER ASSEMBLY STEP 28 CENTER LADDER ON 'M13' BOARD AND PILOT DRILL 3/16" HOLES FOR LADDER ATTACHMENT. ATTACH THE LADDER ASSEMBLY TO M13 FLOOR RAIL SUPPORT USING (2) 2-1/2" LAG SCREWS AND LOCK WASHERS, AS SHOWN.
(1) - SWING BEAM ASSEMBLY (1) HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 STEP 29 ATTACH SWING BEAM ASSEMBLY TO K1 ROOF SWING BEAM SUPPORT USING (4) 1" BOLTS, SPLIT WASHERS AND FLAT WASHERS, AS SHOWN BELOW. ATTACH HC I.D. TAG TO SB74 SWING BEAM USING (4) 5/8" PFH SCREWS, AS SHOWN.
(1) - MONKEY BAR ASSEMBLY STEP 30 ATTACH MONKEY BAR ASSEMBLY TO K2 BOARD USING HARDWARE AS SHOWN.
(4) EZ - CHAIN GREEN 51.25" - A100068 (2) FB - SWING SEAT YELLOW - A100070 (2) DO - CAPTAINS GLIDER ARM YELLOW - A100026 (4) JD - CHAIN GREEN 45" - A100092 (1) DN - GLIDER SEAT DARK GREEN - A100025 STEP 31 ATTACH FB SWING SEAT TO (2) EZ CHAINS USING (2) FA QUICK LINKS, AS SHOWN. REPEAT PROCESS TO ASSEMBLE SECOND SWING ASSEMBLY. NOW, ATTACH EZ CHAINS TO SWING HANGER QUICK LINKS ALREADY ASSEMBLED TO THE SWING BEAM.
(1) SQ - "A" REVISION TAG - A100314 (8) KC - METAL GROUND STAKE BROWN - A100178 Anchoring Instructions STAKE A STAKE A (4) BOLT WH 1/4x1/2" BOLT WH 1/4x1 (4) STAKE A (8) WASHER LOCK EXT 8x15 WASHER FLAT 9x18 (8) (8) NOTE: NUT BARREL WH 1/4x5/8 (2) FAILURE TO USE GROUND STAKES CAN VOID WARRANTY & CAUSE INJURY! STAKE B SCREW PWH 8x5/8 STAKE B STAKE B STEP 32 ATTACH TO MONKEY BAR AND SWING BEAM USING 1" BOLTS, FLAT WASHERS, 8X19 LOCK WASHERS AND 5/8" BARREL NUTS IN PLACES WHERE "STAKE A" IS N
Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories.
