P R O V ID E N C E Wooden Swing Set Model: #40112 •• •• •• •• Owner's Manual Frequently Asked Questions Assembly Instructions Warranty Information Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetsonline.com (you will also find any updates on assembly instructions and information to order replacement parts) Features the fastening system.
STOP PARE Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com ¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA! La tienda donde realizó la compra no almacena piezas de este producto.
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing material washing away during heavy rains. 3.
Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth Wood Chips Double-Shredded bark mulch Engineered Wood Fibers Fine Sand Coarse Sand Fine Gravel Medium Gravel 6" (152mm) 7' (2.13m) 6' (1.83m) 6' (1.83m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 9" (228mm) 10' (3.05m) 10' (3.05m) 7' (2.13m) 5' (1.52m) 5' (1.52m) 7' (2.
Owner’s Manual Play Set 16. Instruct children to never crawl or walk across the top of monkey bars. 17. Instruct children to never crawl on top of a fort roof. 18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that they cannot be looped back on it. 19.
Owner’s Manual Play Set Disposal Instructions: When the Playcenter use is no longer desired, it should be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the unit is discarded. Third Party Assembly: Customer may, in their sole discretion, elect to use a third party person or service to assemble this product. Backyard Discovery assumes no responsibility or liability for any charge incurred by the Customer for any assembly services’.
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS11 X3.1 The U.S.
Play Set Assembly Manual FAQs: 1. Does the area for the playset need to be level? Yes. Backyard Discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3.
www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the assembly manual and get the tools ready for the job as recommended in the manual. If the assembly manual is lost or misplaced a new one can be printed from Backyard Discovery’s website: www.swingsetsonline.com. 9. The playset seems to rock or sway too much. What’s wrong? Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground rails.
Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.
Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 25'-1 1/2" [7.7 m] 13'-1 1/2" [4 m] 22'-11 1/2" [7 m] 10'-11 1/2" [3.3 m] 6' [2 m] Safe Play Zone General Information: Your set has been designed and engineered for children only and for residential use only. A maximum of 150 lbs.
Parts Identification Wood Components (NOT TO SCALE) E1 - FORT UPRIGHT - W102297 (4) 1 3/8"x3 3/8"x83" (36x86x2108) E77 - ANGLE BRACE - W100991 (2) 1 3/8"x3 3/8"x74 3/8" (36x86x1890) G1 - PICNIC TOP SUPPORT - W102300 (2) 1"x5 1/4"x15" (24x134x381) H1 - ROOF CROSS BRACE - W102301 (2) 1"x3 3/8"x62 1/2" (24x86x1588) H2 - ROCKWALL SUPPORT - W102334 (2) 1"x3 3/8"x48 7/8" (24x86x1242) H3 - TARP UPRIGHT - W102340 (2) 1"x3 3/8"x37" (24x86x940) H4 - FLOOR JOIST - W102308 (2) 1"x3 3/8"x30" (24x86x762) H5
Parts Identification Wood Components (NOT TO SCALE) K3 - WALL RAIL - W102302 (3) 5/8"x5 1/4"x30" (16x134x762) K4 - ARCHED WALL RAIL - W102306 (2) 5/8"x5 1/4"x30" (16x134x762) K5 - OUTER FLOOR BOARD - W102333 (2) 5/8"x5 1/4"x27 1/8" (16x134x688) M1 - ANGLE BRACE - W102310 (2) 5/8"x3 3/8"x59" (16x86x1500) M2 - TARP SUPPORT - W102337 (2) 5/8"x3 3/8"x31 7/8" (16x86x810) M3 - PICNIC SEAT/TOP - W102347 (4) 5/8"x3 3/8"x31" (16x86x786) M4 - FLOOR BOARD - W102332 (6) 5/8"x3 3/8"x30 7/8" (16x86x785) M5
Parts Identification Wood Components (NOT TO SCALE) M11 - ROCKWALL BOARD - W102336 (6) 5/8"x3 3/8"x20 1/4" (16x86x514) M12 - WALL RAIL - W102339 (2) 5/8"x3 3/8"x4" (16x86x102) M77 - SLIDE BRACE - W100544 (1) 5/8"x3 3/8"x17 1/4" (16x86x438) M78 - CENTER SLIDE BRACE - W100545 (2) 5/8"x3 3/8"x17 1/4" (16x86x438) N1 - WALL SLAT - W102343 (2) 5/8"x2 3/8"x23" (16x60x584) N2 - PICNIC TABLE BRACE - W102345 (4) 5/8"x2 3/8"x12" (16x60x305) N3 - TIE STRAP - W102344 (2) 5/8"x2 3/8"x6" (16x60x152) O1 - SAFE
Parts Identification Hardware (6) BOLT WH 5/16x1/2 - H100115 (2) BOLT WH 5/16x1 - H100008 (23) BOLT WH 5/16x1-1/2 - H100010 (4) BOLT HEX 5/16x1-1/4 - H100042 (2) BOLT HEX 5/16x2-3/4 - H100047 (7) BOLT FA 3/8x1-1/2 - H100001 (6) BOLT WH 5/16x1-3/4 - H100011 (1) LAG SCREW WH 5/16x1-1/2 - H100026 (16) BOLT WH 5/16x2 - H100012 (26) LAG SCREW WH 5/16x2 - H100027 (2) BOLT WH 5/16x2-1/4 - H100013 (4) BOLT WH 1/4x1" - H100137 (2) BOLT WH 5/16x2-1/2 - H100014 (14) SCREW PWH 8x5/8 - H100128 (1) BOLT WH 5/1
Parts Identification Hardware (92) SCREW PFH 8x1-1/8" - H100088 (4) T-NUT 1/4 - H100072 (57) SCREW PFH 8x1-1/2" - H100086 (7) SCREW PFH 8x2 - H100111 (13) SCREW PFH 8x2-1/4 - H100091 (6) T-NUT 5/16 - H100074 (9) NUT BARREL WH 5/16x5/8 - H100004 (47) NUT BARREL WH 5/16x7/8 - H100005 (2) NUT BARREL WH 5/16x1-1/2 - H100006 (9) NUT LOCK 5/16 - H100110 (6) SWING HANGER QUICK LINK - H100099 (33) SCREW PFH 8x3 - H100092 (6) T-NUT 3/8 - H100073 (58) WASHER LOCK EXT 12x19 - H100031 (73) WASHER LOCK EXT
Parts Identification Accessories (NOT TO SCALE) - SLIDE RAIL 8' BLUE RIGHT (1) GZ -A100161 - SLIDE RAIL 8' BLUE LEFT (1) HA -A100162 EM - SLIDE BED 8' YELLOW (1) -A100056 - TARP .
Parts Identification Accessories (NOT TO SCALE) - T-40 Wrench (2) -A100041 - HAND GRIP YELLOW PLASTIC (2) EA -A100043 - T-40 Torx Driver (2) -A100042 - CLIMBING ROCK BLUE SMALL (6) GX -A100159 - PLASTIC GROUND STAKE BROWN (6) KD -A100179 - L BRACKET 66x66x127 BLUE (2) GQ -A100153 - T-30 Torx Driver (2) -A100147 - T-30 Wrench (2) -H100114 (1) BYD ID TAG (LARGE) 2011 WITH AGES - A100164 (2) SB - TRIANGLE PLATE 100 5 HOLE -A100309
8 FOOT SLIDE ASSEMBLY PHASE 1 STEP 1 TOP ● DRILL 3 HOLES AT ONE END OF THE PLASTIC SLIDE BED USING A 3/8" DRILL BIT AND USING THE DIMENSIONS SHOWN BELOW. THIS END WILL BE THE TOP OF THE SLIDE. ● TAKE NOTE OF SLIDE BED SURFACE FINISH, THE DULL SIDE WILL BE TOWARDS THE GROUND. PLACE SLIDE BRACE CENTERED ON THE BOTTOM (DULL SIDE) AND 1/4" FROM THE EDGE. TRANSFER HOLES ON THE BOARD THROUGH THE SLIDE BED AS SHOWN BELOW. USE A 3/8" DRILL BIT. ● ATTACH SLIDE BRACE TO SLIDE USING HARDWARE SHOWN.
8 FOOT SLIDE ASSEMBLY STEP 2 PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE SLIDE RAIL. PUT SLIDE SUPPORT BOTTOM INTO THE SUPPORT POCKET AT THE BOTTOM OF THE RAIL AND HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT THE BED INTO THE SLIDE CAVITY. MAKE SURE SLIDE BED IS COMPLETELY DOWN IN THE SLIDE CAVITY. PLACE THE OTHER SLIDE RAIL ON A FLAT SURFACE WITH THE SLIDE CAVITY UP.
(1) SB74 - SWING BEAM - W102304 2"x5 1/4"x89 1/2" (50x134x2274) (2) GQ - L BRACKET 66x66x127 BLUE - A100153 (2) SB - TRIANGLE PLATE 100 5 HOLE - A100309 SWING BEAM ASSEMBLY (3) STEP 1 BOLT WH 5/16x1-3/4 (2) ATTACH (2) SB TRIANGLE PLATES TO SB74 SWING BEAM USING 1-3/4" BOLTS, LOCK WASHER AND 7/8" BARREL NUT. (3) WASHER LOCK EXT 12x19 (4) ATTACH (2) GQ L BRACKETS TO SB74 SWING BEAM USING 2-3/4" HEX BOLTS, FLAT WASHERS AND 5/16" LOCK NUTS.
(1) W71 - SWING BEAM SUPPORT - W102349 2"x3 3/8"x47 3/8" (50x86x1204) (1) H79 - END SUPPORT - W100992 1"x3 1/2"x42" (24x86x1072) (2) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (1) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) SWING BEAM ASSEMBLY (4) STEP 2 INSERT (2) 2-1/2" BOLTS, LOCK WASHERS AND 1-1/2" BARREL NUTS INTO TOP EDGE OF W71 SWING BEAM SUPPORT, AS SHOWN.
SWING BEAM ASSEMBLY STEP 3 (4) WASHER FLAT 8x27 (2) ATTACH (2) SB TRIANGLE PLATES TO W71 SWING BEAM SUPPORT USING 1-3/4" BOLTS, LOCK WASHER AND 7/8" BARREL NUT. (4) INSERT SWING HANGER QUICK LINK AND SAFETY WASHER INTO HOLES IN THE EDGE OF SB74 SWING BEAM. SECURE SWING HANGER TO W71 SWING BEAM USING FLAT WASHERS AND 5/16" LOCK NUTS.
M1 - ANGLE BRACE - W102310 5/8"x3 3/8"x59" (16x86x1500) (1) K1 - GROUND BOARD - W102299 5/8"x5 1/4"x88 7/8" (16x134x2256) (2) E1 - FORT UPRIGHT - W102297 1 3/8"x3 3/8"x83" (36x86x2108) (1) K3 - WALL RAIL - W102302 5/8"x5 1/4"x30" (16x134x762) (1) H1 - ROOF CROSS BRACE - W102301 1"x3 3/8"x62 1/2" (24x86x1588) (1) M6 - FLOOR SUPPORT - W102331 5/8"x3 3/8"x30" (16x86x762) (2) (1) H4 - FLOOR JOIST - W102308 1"x3 3/8"x30" (24x86x762) (1) H5 - SWINGBEAM RAIL - W102303 1"x3 3/8"x30" (24x86x762) STEP
(2) E1 - FORT UPRIGHT - W102297 1 3/8"x3 3/8"x83" (36x86x2108) (2) K3 - WALL RAIL - W102302 5/8"x5 1/4"x30" (16x134x762) (1) H4 - FLOOR JOIST - W102308 1"x3 3/8"x30" (24x86x762) (1) H1 - ROOF CROSS BRACE - W102301 1"x3 3/8"x62 1/2" (24x86x1588) (1) M6 - FLOOR SUPPORT - W102331 5/8"x3 3/8"x30" (16x86x762) (1) O1 - SAFETY BOARD - W102307 5/8"x1 3/8"x30" (16x34x762) STEP 4 LAY TWO E1 FORT UPRIGHTS FLAT ON GROUND.
(2) K4 - ARCHED WALL RAIL - W102306 5/8"x5 1/4"x30" (16x134x762) (2) M5 - FLOOR SUPPORT - W102309 5/8"x3 3/8"x30" (16x86x762) (2) K2 - GROUND BOARD - W102298 5/8"x5 1/4"x52 1/2" (16x134x1334) (2) M2 - TARP SUPPORT - W102337 5/8"x3 3/8"x31 7/8" (16x86x810) STEP 7 E1 E1 STAND UP UPRIGHT ASSEMBLIES AND ATTACH (2) K2 GROUND BOARDS TO E1 FORT UPRIGHTS USING 2" LAG SCREWS AND LOCK WASHERS.
(2) (1) K5 - OUTER FLOOR BOARD - W102333 5/8"x5 1/4"x27 1/8" (16x134x688) H6 - FLOOR SUPPORT - W102338 1"x3 3/8"x30" (24x86x762) STEP 10 ATTACH H6 FLOOR SUPPORT TO M5 FLOOR SUPPORTS USING 2-1/4" SCREWS. H6 M5 (8) SCREW PFH 8x2-1/4 (4) SCREW PFH 8x1-1/2" H6 STEP 11 K5 ATTACH (2) K5 OUTER FLOOR BOARDS TO H4 FLOOR JOISTS AND M5 FLOOR SUPPORTS USING 1-1/2" WOOD SCREWS.
(6) M4 - FLOOR BOARD - W102332 5/8"x3 3/8"x30 7/8" (16x86x785) (2) STEP 12 M12 - WALL RAIL - W102339 5/8"x3 3/8"x4" (16x86x102) M4 EVENLY SPACE (6) M4 FLOOR BOARDS AND ATTACH TO H4 FLOOR JOISTS USING 1-1/2" SCREWS. H4 ATTACH H6 FLOOR SUPPORT TO M4 FLOOR BOARDS USING 1-1/2" SCREWS. H6 H4 (20) SCREW PFH 8x1-1/2" (2) LAG SCREW WH 5/16x2 1/16 GAP TYP. M4 STEP 13 ATTACH (2) M12 WALL RAILS TO E1 FORT UPRIGHTS USING 2" LAG SCREWS AND LOCK WASHERS.
(6) (2) M11 - ROCKWALL BOARD - W102336 5/8"x3 3/8"x20 1/4" (16x86x514) H2 - ROCKWALL SUPPORT - W102334 1"x3 3/8"x48 7/8" (24x86x1242) (6) GX - CLIMBING ROCK BLUE SMALL - A100159 M10 - ROCKWALL BOARD - W102335 (2) 5/8"x3 3/8"x20 1/4" (16x86x514) STEP 14 TO BUILD THE ROCK WALL LADDER ASSEMBLY, START BY ATTACHING THE GX CLIMBING ROCKS TO M11 WALL BOARDS USING 1-1/2" BOLTS, 3/8" T-NUTS AND 1-1/8" WOOD SCREWS.
(6) M9 - WALL SLAT - W102342 5/8"x3 3/8"x23" (16x86x584) STEP 16 ATTACH (3) M9 WALL SLATS TO K3 WALL RAIL AND M6 FLOOR SUPPORT USING 1-1/8" WOOD SCREWS. 3 1/4" (3 PLCS) K3 (12) M9 SCREW PFH 8x1-1/8" 1 13/16" M6 STEP 17 ATTACH (3) M9 WALL SLATS TO K3 WALL RAIL AND M6 FLOOR SUPPORT USING 1-1/8" WOOD SCREWS.
(2) N1 - WALL SLAT - W102343 5/8"x2 3/8"x23" (16x60x584) (1) M8 - TARP SUPPORT - W102341 5/8"x3 3/8"x30" (16x86x762) (2) H3 - TARP UPRIGHT - W102340 1"x3 3/8"x37" (24x86x940) STEP 18 ATTACH (2) N1 WALL SLATS TO K4 ARCHED WALL RAIL AND M12 WALL RAIL USING 1-1/8" WOOD SCREWS. N1 22 7/16" N1 N1 (8) SCREW PFH 8x1-1/8" K4 M12 1 15/16" STEP 19 M8 ATTACH H3 TARP UPRIGHT TO H1 ROOF CROSS BRACE AND K3 WALL RAIL USING 2" BOLT, LOCK WASHER, 5/16" T-NUT AND 1-1/2" WOOD SCREWS.
(1) SC - TARP .4x760x2505 - A100310 1/64"x29 7/8"x98 5/8" (.4x760x2505) STEP 20 DRAPE SC TARP OVER M2 AND M8 TARP SUPPORTS. ATTACH ONE SIDE OF TARP TO INSIDE OF ONE M2 TARP SUPPORT USING 5/8" SCREWS. PULL OTHER SIDE OF TARP TIGHT AND ATTACH TO OTHER M2 TARP SUPPORT USING 5/8" SCREWS. SECURE TOP OF TARP TO M8 TARP SUPPORT USING 5/8" SCREWS, AS SHOWN.
(2) G1 - PICNIC TOP SUPPORT - W102300 1"x5 1/4"x15" (24x134x381) PILOT DRILL HOLE LOCATION 3 15/16" 6 15/16" 1 1/8" 27 13/16" E1 G1 (4) SCREW PFH 8x3 BOARD PLACEMENT DIMEMSION STEP 21 PILOT DRILL USING 1/8" BIT AND ATTACH (2) G1 PICNIC TOP SUPPORTS TO E1 FORT UPRIGHTS USING 3" WOOD SCREWS. SEE PILOT DRILL HOLE LOCATION & BOARD PLACEMENT DIMENSIONS FOR PROPER PLACEMENT.
M3 - PICNIC SEAT/TOP - W102347 5/8"x3 3/8"x31" (16x86x786) (4) (2) N3 - TIE STRAP - W102344 5/8"x2 3/8"x6" (16x60x152) N3 M3 STEP 22 (4) (4) SCREW PFH 8x1-1/8" ATTACH N3 TIE STRAP TO (2) M3 PICNIC SEAT / TOP USING 1-1/8" WOOD SCREWS. REPEAT PROCESS TO ASSEMBLE PICNIC TABLE SEAT ASSEMBLY. SCREW PFH 8x1-1/2" STEP 23 ATTACH PICNIC TABLE TOP ASSEMBLY TO G1 PICNIC TOP SUPPORTS USING 1-1/2" WOOD SCREWS.
(4) N2 - PICNIC TABLE BRACE - W102345 5/8"x2 3/8"x12" (16x60x305) (2) J1 - TIE STRAP - W102346 1"x2 3/8"x7" (24x60x178) STEP 24 ATTACH J1 TIE STRAP TO (2) N2 PICNIC TABLE BRACES USING 1-1/2" WOOD SCREWS. REPEAT PROCESS TO ASSEMBLE SECOND SEAT SUPPORT ASSEMBLY. J1 SCREW PFH (8) 8x1-1/8" SCREW PFH (4) 8x1-1/2" N2 STEP 25 ATTACH SEAT SUPPORT ASSEMBLY TO K2 GROUND BOARDS USING 1-1/8" WOOD SCREWS.
TABLE TOP & SEAT ASSEMBLY SCREW PFH (4) 8x1-1/2" STEP 26 ATTACH TABLE TOP & SEAT ASSEMBLY TO (2) J1 TIE STRAPS USING 1-1/2" WOOD SCREWS.
(2) EA - HAND GRIP YELLOW PLASTIC - A100043 BOLT WH (4) 1/4x1" WASHER (4) LOCK EXT 6x15 (4) T-NUT 1/4 STEP 27 N1 ATTACH EA HANDLE GRIPS TO N1 WALL SLATS USING 1/4"x 1" BOLTS, 6x15 LOCK WASHERS AND 1/4" T-NUTS. USING A 5/16" DRILL BIT PILOT DRILL AND INSTALL 1/4" T-NUTS INTO THE BACK SIDE OF N1 WALL SLATS. SECURE INTO PLACE USING A HAMMER.
STEP 28 BEGIN BY PILOT DRILLING H1 ROOF CROSS BRACE WITH 3/8" BIT USING SWING BEAM ASSEMBLY ANGLE BRACKETS AS A TEMPLATE. ATTACH SWING BEAM ASSEMBLY TO H1 ROOF CROSS BRACE AND H5 SWING BEAM RAIL USING 1-1/4" HEX BOLTS, SPLIT WASHERS, FLAT WASHERS AND 5/16" T-NUTS. WASHER (4) SPLIT 5/16 BOLT HEX (4) 5/16x1-1/4 ATTACH HC ID PLATE TO SWING BEAM USING 5/8" SCREWS, AS SHOWN.
STEP 29 CENTER SLIDE ASSEMBLY IN OPENING, AS SHOWN. USING HOLE PATTERN BELOW, PILOT DRILL (3) SLIDE ATTACHMENT HOLES IN SLIDE BED AND K5 OUTER FLOOR BOARD USING 3/8" BIT AND ATTACH SLIDE ASSEMBLY USING 1/2" BOLTS, LOCK WASHER AND 5/8" BARREL NUTS.
(6) KD - PLASTIC GROUND STAKE BROWN - A100179 (1) KF - TRAPEZE WITH BLUE ROPE CHAIN - A100109 (1) TQ - SWING SEAT WITH BLUE ROPE CHAIN - A100170 Anchoring Instructions *STAKES SHOULD BE PLACED IN CONCRETE* NOTE: FAILURE TO USE STAKES CAN VOID WARRANTY & CAUSE INJURY! STAKE STAKE STEP 30 SWING (6) DRIVE STAKES INTO GROUND AGAINST BOARDS WHERE SHOWN AND ATTACH WITH 2" WOOD SCREWS. ATTACH TQ SWING SEATS ASSEMBLY TO SWING BEAM ASSEMBLY.
Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories.
