SCENIC Play House Model: #36013 WARNING Adult Assembly Required. Not suitable for children under two years, due to sharp points and small parts. • Owner's Manual • Frequently Asked Questions • Assembly Instructions • Warranty Information Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new play house on-line @ www.swingsetsonline.
STOP Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com 1-800-856-4445 PLEASE READ THIS BEFORE STARTING ASSEMBLY • • • • • READ THE ASSEMBLY MANUAL COMPLETELY, PAYING SPECIAL ATTENTION TO THE IMPORTANT TIPS AND SAFETY INFORMATION.
Owner’s Manual Play House Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 2 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play House Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Play house 1. The Play house is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play house tipping over and loose-fill surfacing material washing away during heavy rains. 3.
Owner’s Manual Play House The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth Wood Chips Double-Shredded bark mulch Engineered Wood Fibers Fine Sand Coarse Sand Fine Gravel Medium Gravel 6" (152mm) 7' (2.13m) 6' (1.83m) 6' (1.83m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 9" (228mm) 10' (3.05m) 10' (3.05m) 7' (2.13m) 5' (1.52m) 5' (1.
Owner’s Manual Play House 4. For rusted areas on metallic members such as hand supports, brackets, etc., sand and repaint, using a non lead-based paint meeting the requirements of Title 16 CRF Part 1303. 5. Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. 6. Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear.
Owner’s Manual Play House APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information:. www.cpsc.gov/cpscpub/pubs/323.html X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS11 X3.
Owner’s Manual Play House 11 This information has been extracted from the CPSC publications “Playground Surfacing — Technical Information Guide” and “Handbook for Public Playground Safety.” Copies of these reports can be obtained by sending a postcard to: Office of Public Affairs, U.S. Consumer Product Safety Commission, Washington, D.C., 20207 or call the toll-free hotline: 1800-638-2772.
Play House Assembly Manual FAQs: 1. Does the area for the play house need to be level? Yes. Backyard Discovery recommends the play house be positioned on a flat level area for maximum safety and durability. Any stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the play house? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the play house for maximum safety. 3.
Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.
SAFETY AND ASSEMBLY INFORMATION SELECTING THE CORRECT LOCATION FOR YOUR PLAY PRODUCT IS IMPORTANT FOR YOUR CHILDREN’S SAFETY AND THE PRODUCT’S LONGEVITY Dimensions: • The Scenic has one layout option. Layout Ground Dimension Safe Play Area* 5'-4 1/2" x 4'-2 1/2" x 4'-7" Tall 17'-4 1/2" x 16'-2 1/2" *Level Ground Surface - See below General Information: Your set has been designed and engineered for children only and for residential use only. A maximum of 150 lbs.
Parts Identification Wood Components (NOT TO SCALE) H1 - SHELF SUPPORT - W103891 1"x3 3/8"x3 7/8" (24x86x98) (7) H4 - BENCH SEAT SUPPORT - W104040 1"x3 3/8"x6 1/2" (24x86x166) (2) (2) H6 - BENCH GROUND BOARD - W104042 1"x3 3/8"x18 1/8" (24x86x460) (2) (1) J1 - SHELF SUPPORT - W103895 1"x2 3/8"x38 3/8" (24x60x976) (2) J2 - SHELF SUPPORT - W103896 1"x2 3/8"x8 7/8" (24x60x224) J3 - SHELF SUPPORT - W103897 1"x2 3/8"x8 7/8" (24x60x224) (2) (1) (1) (1) (2) (2) H5 - BENCH UPRIGHT - W104041 1"x3
Parts Identification Wood Components (NOT TO SCALE) L1 - SIDE WALL HEADER - W103887 5/8"x4 3/8"x42 5/8" (16x112x1082) (2) (2) K6 - WALL HEADER - W103883 5/8"x5 1/4"x41 3/8" (16x134x1050) (4) L3 - RAFTER - W104047 5/8"x4 1/4"x28 3/8" (16x108x692) (2) K7 - ANGLED WALL BOARD - W103885 5/8"x4 5/8"x23 3/4" (16x117x602) (2) L5 - ANGLED WALL BOARD - W103886 5/8"x4 3/8"x23 3/4" (16x112x602) (4) M1 - WALL BOARD - W103881 5/8"x3 3/8"x23 1/2" (16x86x596) (2) M2 - BENCH SEAT - W104044 5/8"x3 3/8"x27 3/8"
Parts Identification Wood Components (NOT TO SCALE) (2) N1 - WALL BOARD - W103880 5/8"x2 3/8"x40 1/8" (16x60x1020) (2) N2 - WALL BOARD - W103882 5/8"x2 3/8"x40 1/8" (16x60x1020) (4) N3 - WALL BOARD - W103888 5/8"x2 3/8"x23 3/4" (16x60x602) (1) N4 - ROOF CAP - W104049 5/8"x2 3/8"x48 3/4" (16x60x1238) (2) N5 - DOOR TRIM - W104055 5/8"x2 3/8"x11 1/4" (16x60x286) (1) N6 - DOOR STOP - W104056 5/8"x2 3/8"x3 7/8" (16x60x100) (1) O1 - ROOF CAP - W104050 5/8"x1 3/8"x48 3/4" (16x34x1238) (4) P1 - CORN
Parts Identification Wood Components (NOT TO SCALE) (1) WP3 - WALL PANEL - W103877 1 1/4"x18 1/8"x41 3/8" (32x460x1050) (2) RP1 - ROOF PANEL - W104046 1 3/8"x28 1/8"x48 3/4" (34x715x1238) DP1 - DOOR PANEL - W104048 (1) 1 1/4"x16 7/8"x18 1/2" (32x430x470)
Parts Identification Hardware (26) K - BOLT WH 5/16x2 - H100012 (9) (4) D - NUT BARREL WH 5/16x7/8 - H100005 H - BOLT WH 5/16x1 1/2 - H100010 (30) BG - T-NUT 5/16 - H100074 (4) G - BOLT WH 5/16x1 1/4 - H100009 (35) AC - WASHER LOCK EXT 8x19 - H100030 (2) (2) (2) (9) AD - WASHER LOCK EXT 12x19 - H100031 F - BOLT WH 5/16x1 - H100008 (17) TS - SCREW PWH 8x1-1/4 - H100180 CM - BOLT WH 5/16x1/2 - H100115 (25) BC - SCREW PWH 8x3/4 - H100070 BW - SCREW PFH 8x3 - H100092 (7) (26) BS - SCREW PFH 8
Parts Identification Accessories (NOT TO SCALE) (1) JR - FAUCET KIT - A100125 (1) MS - PHONE KIT - A100132 (1) JS - SQUARE SINK BOWL - A100129 (2) (1) TD - HINGE (DOOR, SPRING LOADED) - A100327 XR - BYD ID TAG (SMALL) WITHOUT AGES - A100241 (1) JX - STOVE ASSEMBLY - A100136 (2) (4) SW - PLASTIC WINDOW 44x266x329 - A100320 (2) VB - PLASTIC SUNBURST - A100361 (1) (4) TZ - L BRACKET 2.
(2) M4 - WALL RAIL - W103879 5/8"x3 3/8"x12 1/4" (16x86x310) (4) H1 - SHELF SUPPORT - W103891 1"x3 3/8"x3 7/8" (24x86x98) Left and Right Pot Holder Assemblies Step 1 Pre-drilling 1/8" holes in the back edge of H1 is recommended. Use the existing holes in M4 as a guide.
(2) K5 - REAR FLOWER POT SHELF - W103892 5/8"x2 5/8"x9 1/8" (16x67x232) (2) K4 - FRONT FLOWER POT SHELF - W104051 5/8"x2 5/8"x9 1/8" (16x67x232) Left and Right Pot Holder Assemblies Step 2 Pre-drilling 1/8" holes in the top edge of H1 is recommended. Use the existing holes in K5 and K4 as a guide.
(2) H6 - BENCH GROUND BOARD - W104042 1"x3 3/8"x18 1/8" (24x86x460) (2) TZ - L BRACKET 2.
(2) H5 - BENCH UPRIGHT - W104041 1"x3 3/8"x11 3/4" (24x86x300) Bench Assembly Step 2 H5 (8) SCREW PFH 8x1-3/4 SCREW PFH 8x1-3/4 1 3/16
(2) H4 - BENCH SEAT SUPPORT - W104040 1"x3 3/8"x6 1/2" (24x86x166) Bench Assembly Step 3 (8) SCREW PFH 8x1-3/4 H4 SCREW PFH 8x1-3/4 1 9/16 1 9/16
(2) M2 - BENCH SEAT - W104044 5/8"x3 3/8"x27 3/8" (16x86x694) Bench Assembly Step 4 Pre-drilling 1/8" holes in the top edge of H4 is recommended. Use the existing holes in M2 as a guide.
(1) DP1 - DOOR PANEL - W104048 1 1/4"x16 7/8"x18 1/2" (32x430x470) (2) TD - HINGE (DOOR, SPRING LOADED) - A100327 Door Assembly Step 1 DP1 (6) TD SCREW PWH 8x3/4 SCREW PWH 8x3/4
(1) XR - BYD ID TAG (SMALL) WITHOUT AGES - A100241 Door Assembly Step 2 Center ID tag on door approx. as shown.
(4) P1 - CORNER POST - W103875 1 3/8"x1 3/8"x16 1/2" (36x36x418) PLAY HOUSE ASSEMBLY Step 1 In this step you will make four post assemblies. It is crucial to note the relationship of the ID holes with the T-Nuts in each assembly as indicated below.
WP1 - WALL PANEL - W103874 (1) 1 1/4"x18 1/8"x41 3/16" (32x460x1050) (1) RIGHT REAR POST ASSEMBLY (1) RIGHT FRONT POST ASSEMBLY PLAY HOUSE ASSEMBLY Step 2 WASHER LOCK EXT 8x19 BOLT WH 5/16x2 (6) RIGHT REAR POST ASSEMBLY (6) BOLT WH 5/16x2 WASHER LOCK EXT 8x19 WP1 RIGHT FRONT POST ASSEMBLY
WP2 - WALL PANEL - W103876 (1) 1 1/4"x18 1/8"x42 5/8" (32x460x1082) (1) LEFT REAR POST ASSEMBLY PLAY HOUSE ASSEMBLY Step 3 WASHER LOCK EXT 8x19 BOLT WH 5/16x2 LEFT REAR POST ASSEMBLY (6) (6) WP2 WP1 BOLT WH 5/16x2 WASHER LOCK EXT 8x19
WP3 - WALL PANEL - W103877 (1) 1 1/4"x18 1/8"x41 3/8" (32x460x1050) (1) LEFT FRONT POST ASSEMBLY PLAY HOUSE ASSEMBLY Step 4 (6) WP3 (6) BOLT WH 5/16x2 WASHER LOCK EXT 8x19 BOLT WH 5/16x2 WASHER LOCK EXT 8x19 WP2 LEFT FRONT POST ASSEMBLY WP1
(2) M3 - WALL RAIL - W103878 5/8"x3 3/8"x12 1/4" (16x86x310) PLAY HOUSE ASSEMBLY Step 5 (4) (4) M3 WASHER LOCK EXT 8x19 BOLT WH 5/16x2 BOLT WH 5/16x2 WASHER LOCK EXT 8x19
(4) L3 - RAFTER - W104047 5/8"x4 1/4"x28 3/8" (16x108x692) (2) VB - PLASTIC SUNBURST - A100361 (2) K6 - WALL HEADER - W103883 5/8"x5 1/4"x41 3/8" (16x134x1050) PLAY HOUSE ASSEMBLY Step 6 (4) SCREW PFH 8x1 In this step you will make two Gable Assemblies. Use 1 1/2" bolts and washers to help with the alignment of parts. You may temporary use a T-Nut (not shown) to keep the bolt and washer from falling off. DO NOT TAP IN T-NUT AT THIS TIME.
(2) N1 - WALL BOARD - W103880 5/8"x2 3/8"x40 1/8" (16x60x1020) (1) GABLE ASSEMBLY PLAY HOUSE ASSEMBLY Step 7 FROM STEP 6 (2) GABLE ASSEMBLY (2) (2) FROM STEP 6 SCREW PFH 8x1 1/8 NUT BARREL WH 5/16x7/8 WASHER LOCK EXT 12x19 NUT BARREL WH 5/16x7/8 WASHER LOCK EXT 12x19 N1 SCREW PFH 8x1 1/8 !CAUTION! BE CAREFUL NOT TO LEAN ON OR MOVE THE PARTS IN THIS STEP. THEY ARE NOT FASTENED SECURELY UNTIL LATER IN THE ASSEMBLY PROCESS.
(2) N2 - WALL BOARD - W103882 5/8"x2 3/8"x40 1/8" (16x60x1020) PLAY HOUSE ASSEMBLY Step 8 6 13/16 6 13/16 (8) SCREW PFH 8x1 1/8 N2 THESE HOLES ARE CLOSER TO THE GROUND FLUSH SCREW PFH 8x1 1/8
(1) LEFT POT HOLDER ASSEMBLY (1) RIGHT POT HOLDER ASSEMBLY PLAY HOUSE ASSEMBLY Step 9 (2) (4) WASHER LOCK EXT 8x19 SCREW PFH 8x1 1/8 BOLT WH 5/16x2 WASHER LOCK EXT 8x19 LEFT POT HOLDER ASSEMBLY (2) BOLT WH 5/16x2 SCREW PFH 8x1 1/8 RIGHT POT HOLDER ASSEMBLY
(4) M1 - WALL BOARD - W103881 5/8"x3 3/8"x23 1/2" (16x86x596) (4) M6 - WALL BOARD - W103884 5/8"x3 3/8"x6 7/8" (16x86x175) PLAY HOUSE ASSEMBLY Step 10 (20) SCREW PFH 8x1-1/8 M6 SCREW PFH 8x1-1/8 M1
(1) XP - METAL TIE STRAP - A100414 (1) N6 - DOOR STOP - W104056 5/8"x2 3/8"x3 7/8" (16x60x100) PLAY HOUSE ASSEMBLY Step 11 Attach N6 approximately 2" up from ground and locate as shown.
(2) (2) (1) GABLE ASSEMBLY L5 - ANGLED WALL BOARD - W103886 5/8"x4 3/8"x23 3/4" (16x112x602) N5 - DOOR TRIM - W104055 5/8"x2 3/8"x11 1/4" (16x60x286) PLAY HOUSE ASSEMBLY Step 12 BOLT WH 5/16x1 1/4 (2) (2) GABLE ASSEMBLY FROM STEP 6 (2) WASHER LOCK EXT 12x19 NUT BARREL WH 5/16x7/8 NUT BARREL WH 5/16x7/8 (2) BOLT WH 5/16x1 1/4 (2) L5 SCREW PFH 8x1 1/8 SCREW PFH 8x1 1/8 T-NUT 5/16 FROM STEP 6 T-NUT 5/16 N5 WASHER LOCK EXT 12x19 (4) WASHER LOCK EXT 8x19 WASHER LOCK EXT 8x19
(1) L1 - SIDE WALL HEADER - W103887 5/8"x4 3/8"x42 5/8" (16x112x1082) (2) K7 - ANGLED WALL BOARD - W103885 5/8"x4 5/8"x23 3/4" (16x117x602) PLAY HOUSE ASSEMBLY Step 13 (2) BOLT WH 5/16x1 1/4 L1 SCREW PFH 8x1 1/4 (4) SCREW PFH 8x1 1/8 (4) SCREW PFH 8x1 1/8 SCREW PFH 8x1 1/4 (2) (2) K7 WASHER LOCK EXT 8x19 T-NUT 5/16 BOLT WH 5/16x1 1/4 T-NUT 5/16 WASHER LOCK EXT 8x19 L1 1 5/16 K7
(1) L1 - SIDE WALL HEADER - W103887 5/8"x4 3/8"x42 5/8" (16x112x1082) (2) N3 - WALL BOARD - W103888 5/8"x2 3/8"x23 3/4" (16x60x602) PLAY HOUSE ASSEMBLY Step 14 SCREW PFH 8x1-1/4 SCREW PFH 8x1-1/8 L1 (8) (4) N3 L1 1 5/16 N3 SCREW PFH 8x1-1/4 SCREW PFH 8x1-1/8
(4) M5 - WALL BOARD - W103889 5/8"x3 3/8"x7" (16x86x178) (4) M6 - WALL BOARD - W103884 5/8"x3 3/8"x6 7/8" (16x86x175) (2) N3 - WALL BOARD - W103888 5/8"x2 3/8"x23 3/4" (16x60x602) PLAY HOUSE ASSEMBLY Step 15 M6 (24) SCREW PFH 8x1-1/8 N3 M5 SCREW PFH 8x1-1/8
(1) J1 - SHELF SUPPORT - W103895 1"x2 3/8"x38 3/8" (24x60x976) PLAY HOUSE ASSEMBLY Step 16 (5) SCREW PFH 8x1 1/2 J1 FLUSH SCREW PFH 8x1 1/2
(2) J2 - SHELF SUPPORT - W103896 1"x2 3/8"x8 7/8" (24x60x224) PLAY HOUSE ASSEMBLY Step 17 (4) SCREW PFH 8x1 1/2 FLUSH J2 SCREW PFH 8x1 1/2
(1) K3 - REAR COUNTER TOP - W103894 5/8"x5 1/4"x40 1/8" (16x134x1018) (1) K2 - FRONT COUNTER TOP - W103893 5/8"x5 1/4"x40 3/4" (16x134x1034) PLAY HOUSE ASSEMBLY Step 18 (11) SCREW PFH 8x1 1/2 K2 HOLES TO RIGHT OF SINK K3 SCREW PFH 8x1 1/2
(2) J3 - SHELF SUPPORT - W103897 1"x2 3/8"x8 7/8" (24x60x224) PLAY HOUSE ASSEMBLY Step 19 (8) SCREW PFH 8x1 1/2 SCREW PFH 8x3 SCREW PFH 8x1 1/2 J3 (2) SCREW PFH 8x3
(4) WP - SMALL PLASTIC WINDOW INSIDE TRIM - A100364 (4) SW - PLASTIC WINDOW 44x266x329 - A100320 PLAY HOUSE ASSEMBLY Step 20 Center windows in openings and attach as shown. Pre-drilling 3/16" holes using WP as a guide is recommended.
(1) K1 - SERVING SHELF - W103890 5/8"x5 1/4"x35 5/8" (16x134x906) (3) H1 - SHELF SUPPORT - W103891 1"x3 3/8"x3 7/8" (24x86x98) PLAY HOUSE ASSEMBLY Step 21 (9) SCREW PFH 8x1 1/2 H1 K1 H1 SCREW PFH 8x1 1/2
(1) RP1 - ROOF PANEL - W104046 1 3/8"x28 1/8"x48 3/4" (34x715x1238) PLAY HOUSE ASSEMBLY Step 22 FLUSH RP1 (4) RP1 SCREW PFH 8x1-1/2 SCREW PFH 8x1-1/2
(1) RP1 - ROOF PANEL - W104046 1 3/8"x28 1/8"x48 3/4" (34x715x1238) PLAY HOUSE ASSEMBLY RP1 Step 23 RP1 SCREW PFH 8x1 1/2 (4) SCREW PFH 8x1 1/2
(1) N4 - ROOF CAP - W104049 5/8"x2 3/8"x48 3/4" (16x60x1238) (1) O1 - ROOF CAP - W104050 5/8"x1 3/8"x48 3/4" (16x34x1238) PLAY HOUSE ASSEMBLY Step 24 N4 (10) SCREW PFH 8x1 1/8 O1 SCREW PFH 8x1 1/8 N4 O1
(1) BENCH ASSEMBLY PLAY HOUSE ASSEMBLY Step 25 (2) WASHER LOCK EXT 12x19 (2) (2) BENCH ASSEMBLY BOLT WH 5/16x1 WASHER LOCK EXT 12x19 NUT BARREL WH 5/16x7/8 BOLT WH 5/16x1 NUT BARREL WH 5/16x7/8
(1) JX - STOVE ASSEMBLY - A100136 (1) JS - SQUARE SINK BOWL - A100129 PLAY HOUSE ASSEMBLY Step 26 SCREW PWH 8x3/4 SCREW PFH 8x1 1/8 JX JS (4) SCREW PFH 8x1 1/8 (1) SCREW PWH 8x3/4
(1) JR - FAUCET KIT - A100125 (1) MS - PHONE KIT - A100132 PLAY HOUSE ASSEMBLY Step 27 MS SCREW PFH 8x1/2 JR SCREW PFH 8x1-1/4 (2) SCREW PFH 8x1-1/4 (2) SCREW PFH 8x1/2
(1) DOOR ASSEMBLY PLAY HOUSE ASSEMBLY Step 28 Upon completion of this step, double check to make sure every bolt, screw and nut is tight. Make sure every board is secure. Make sure the play house is level.
Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories.
warranty. Backyard Discovery disclaims all other representations and warranties of any kind, express or implied. This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of consequential damages and therefore this limitation may not apply to you.
