Manufactured by: Backyard Discovery 3305 Airport Drive, Pittsburg, KS 66762 800-856-4445 Basepoint Business Centre: Rivermead Drive,Westlea, Swindon SN5 7EX Phone: 0800-118-2476 J.P. Coenstraat 7, The Bridge, The Hague, 2595 WP, Netherlands Phone: 08005678990 14x10 Cordova Gazebo MODEL # : 2106536B Please visit www.backyarddiscovery.com For the most up to date assembly manual, to register your product, or to order replacement parts Para obtener instrucciones en español, visite www.backyarddiscovery.
OWNER'S MANUAL - BASIC SETUP DIMENSIONS & ASSEMBLY NOTES It is critically important that you start with square and level footings, concrete pad or deck to attach your structure • Pay close attention to the items needed for each step. Make sure you are using the correct hardware for each step.
OWNER'S MANUAL - ANCHORING LAYOUT 3
OWNER'S MANUAL - PARTS IDENTIFICATION Wood Components (Not to Scale) H01 ROOF JOIST-W4L16213 (2) 1"x3 3/8"x"88 3/16" (24x86x2240) H02 ROOF JOIST- W4L14430 (2) 1"x3 3/8"x46 3/4" (24x86x1188) H03 (2) PURLIN - W4L14420 1"x3 3/8"x68 3/8" (24x86x1736) H04 (2) PURLIN - W4L14422 1"x3 3/8"x98 3/16" (24x86x2494) H05 PURLIN-W4L16207 (4) 1"x3 3/8"x65 1/2" (24x86x1664) H07 PURLIN-W4L16208 (4) 1"x3 3/8"x59 7/16" (24x86x1509) H08 PURLIN-W4L16209 (2) 1"x3 3/8"x 43 11/16" (24x86x1110) H09 ROOF JOIST-W4L16
OWNER'S MANUAL - PARTS IDENTIFICATION Wood Components (Not to Scale) H10 ROOF JOIST-W4L16216 (2) H11 (2) 1"x3 3/8"x76 7/8" (24x86x1952) H13 ROOF JOIST- W4L14438 1"x3 3/8"x15 15/16" (24x86x404) (2) H12 ROOF JOIST-W4L16215 (2) 1"X3 3/8"X76 3/4" (24x86x1952) H14 PURLIN - W4L14447 H15 PURLIN - W4L14448 (2) (2) H16 (2) H17 (2) H18 (1) 1"x3 3/8"x50 1/16" (24x86x1272) 1"x3 3/8"x79 7/8" (24x86x2030) PURLIN - W4L14449 1"x3 3/8"x109 3/4" (24x86x2787) PURLIN - W4L14525 1"x1 3/8"x51 3/8" (24x34x1
OWNER'S MANUAL - PARTS IDENTIFICATION Wood Components (Not to Scale) E01 RAFTER- W4L14431 (2) 1 3/8"x3 3/8"x44" (36x86x1117) E02 RAFTER- W4L14434 (4) E03 (2) 1 3/8"x3 3/8"x63 7/8" (36x86x1622) E06 RAFTER- W4L14432 1 3/8"x3 3/8"x20 7/16" (36x86x519) (2) E04 RAFTER- W4L14523 (2) 1 3/8"x3 3/8"x44" (36x86x1117) E05 RAFTER - W4L14442 (2) 1 3/8"x3 3/8"x42 7/8" (36x86x1087) E07 RAFTER- W4L14444 (2) E12 (2) RAFTER - W4L14524 1 3/8"x3 3/8"x20 7/16" (36x86x519) 1 3/8"x3 3/8"x42 7/8" (36x86
OWNER'S MANUAL - PARTS IDENTIFICATION Wood Components (Not to Scale) C01 CORBEL-W2A03370 (7) 1 3/8"x6 7/16"x36 1/4" (36x163x921) C02 CORBEL W/TAG-W2A03371 (1) 1 3/8"x6 7/16"x36 1/4" (36x163x921) G01 (4) G02 MID BRACE BEAM - W4L14451 1"x5 1/4"x97 13/16" (24x134x2484) (2) G03 BEAM - W4L14452 1"x5 1/4"x77" (24x134x1956) (4) Q01 ROOF JOIST-W4L16210 (4) 1"x4 7/16"x84 9/16" (24x112x2148) Q02 ROOF JOIST-W4L16211 (4) P01 (2) P02 (2) 1"x4 3/8"x61 1/2" (24x112x1562) POST - W2A03124 7"x7"x89 1/2" (178x
OWNER'S MANUAL - PARTS IDENTIFICATION Hardware Components H100792 LAG SCREW WH BLK (13) 1/4x3 H100171 BOLT WH BLK (34) 1/4x1 H100460 LAG SCREW (18) WH BLK 1/4x1 H100488 BOLT WH BLK (15) 1/4x2 H100379 T-NUT BLK (7) 5/16 H100398 T-NUT BLK (34) 1/4 H100407 BOLT WH BLK (9) 5/16x1-1/2 H100378 BOLT WH BLK 5/16x1-3/4 (7) H100205 BOLT WH BLK (x18) 5/16x2-1/4 H100192 NUT BARREL (34) WH BLK 5/16x7/8 H100471 LAG SCREW (34) WH BLK 5/16x1 1/2 H100195 BOLT WH BLK (18) 5/16x2 3/4 H100415 BOLT WH BLK (18) 5/16x
OWNER'S MANUAL - PARTS IDENTIFICATION Hardware Components H100385 SCREW PFH BLK (39) 8x1 H100200 (28) SCREW PFH BLK 8x1 1/2 H100382 SCREW PFH BLK 8x1 3/4 (17) H100391 SCREW PFH BLK (192) 8x2 H100199 WASHER LOCK EXT BLK 12x19 (76) H100536 SCREW PWH BLK (30) 8x1 1/4 H100759 SCREW TAPPING (52) 1/4x3/4 H101030 SCREW CONFIRMAT BLK 7x2 (98) H100833 SCREW WOODGRIP (224) 10x3/4 H100770 WASHER FLAT (17) BLK 5/16 H100198 WASHER LOCK EXT BLK 8x19 (98) H101034 WEATHER PROOF (4) WASHER H100630 WASHER FLAT
OWNER'S MANUAL - PARTS IDENTIFICATION Accessory Components (Not to Scale) A4M01192 PANEL BRACKET (2) A4M01191 PANEL BRACKET (2) A4M01193 PANEL BRACKET (2) A4M01194 PANEL BRACKET (2) A4M01228 RAFTER CLIP (14) A4M01184 PANEL SUPPORT BRACKET (2) A4M00950 STEEL POST PLATE (8) A100241 (1) BYD ID TAG (SMALL) WITHOUT AGES A4M00949 STEEL POST (8) ANCHOR PLATE A4M01185 CORNER BRACKET (4) A6P00296 (4) 7x7 POST FOOT A4M01178 (4) 10 POST CLIP
OWNER'S MANUAL - PARTS IDENTIFICATION Accessory Components (Not to Scale) A4M01200 EDGE TRIM LONG (8) A4M01203 EDGE TRIM SHORT (2) A4M01205 METAL SPACER (4) A4M01202 EDGE TRIM CORNER SPLICE (4) A4M01204 RIDGE PEAK CAP (1) 11 A4M01201 EDGE TRIM SPLICE (6)
OWNER'S MANUAL - PARTS IDENTIFICATION Accessory Components (Not to Scale) A4M01179 29 GA STEEL SHEETING (2) A4M01175 29 GA STEEL SHEETING (2) A4M01176-2 29 GA STEEL SHEETING (2) A4M01176-1 29 GA STEEL SHEETING (2) A4M01177-1 29 GA STEEL SHEETING (2) 9205413 (x1) A4M01177-2 29 GA STEEL SHEETING (2) 12 ELECTRICAL ENCLOSURE
OWNER'S MANUAL - PARTS IDENTIFICATION Accessory Components (Not to Scale) A4M01180-2 29 GA STEEL SHEETING (2) A4M01180-1 29 GA STEEL SHEETING (2) A4M01181-1 29 GA STEEL SHEETING (2) A4M01181-2 (2) 29 GA STEEL SHEETING A4M01199 CORNER RIDGE CAP (4) A4M01198 RIDGE CAP CHANNEL (8) 13
PRE-ASSEMBLY STEP 1 - SORTING PARTS It is critical for ease of assembly that you take the time to sort and organize the wood and hardware. WOOD PARTS: • • • • Organize wood parts by the three-digit, alpha-numeric number stamped on each board (ex. P01). If there are multiple boards with the same stamped number, stack those pieces together. Stamps can be found on the flat surface of the boards or on the end of the boards.
PRE-ASSEMBLY STEP 2 - TOOLS REQUIRED Drill Attachments: Phillips Head Cordless Drill or Electric Drill Open End Wrenches 1/2" & 7/16" 1/8", 3/16", 3/8" & 7/16" Drill Bits Phillips Screw Driver Tape Measure 3/8" Drive Ratchet, 1/2" & 7/16" STD Sockets, 1/2" & 7/16" Deep Sockets 3/8 & 5/16" Nut Drivers Claw Hammer Square Level 24" A6P00460 QUICK RELEASE (2) BAR CLAMP 15 Rubber Mallet Optional
PRE-ASSEMBLY STEP 3 - CHOOSE YOUR ASSEMBLY METHOD There are several types of assembly instructions available to you. 1. Printed Assembly Manual included with your set 2. BILT APP - 3D interactive instructions 3.
STEP 1 - 10FT POST ASSEMBLY P01 (1) P02 (1) A6P00296 POST - W2A03124 (2) 7"x7"x89 1/2" (178x178x2274) POST - W2A03125 7"x7"x89 1/2" (178x178x2274) TIP: • FOR EASE OF ASSEMBLY, SAW HORSES ARE RECOMMENDED FOR STEPS 1 THROUGH 3 17 7x7 POST FOOT
STEP 2 - 10FT POST ASSEMBLY D01 (1) BEAM- W4L14521 1 3/8"x5 1/4"x109 13/16" (36x134x2789) TIP: • SAW DUST CAN BE LEFT BEHIND IN BOLT HOLES. IF YOU HAVE TROUBLE WITH BOLTS ENGAGING, USE A LONG SCREWDRIVER TO REMOVE THE DEBRIS.
STEP 3 - 10FT POST ASSEMBLY C01 (2) CORBEL- W2A03123 1 3/8"x6 7/16"x36 1/4" (36x163x921) TIPS: • INSERT BOLTS FIRST FOLLOW BY LAG SCREWS • TO AVOID WOOD SPLITTING, MAKE SURE LAG SCREWS GO INTO PILOT HOLES 19
STEP 4 - 14FT BEAM ASSEMBLY G02 (1) G03 (2) MID BRACE BEAM - W4L14451 1"x5 1/4"x97 13/16" (24x134x2484) BEAM - W4L14452 1"x5 1/4"x77" (24x134x1956) 21
STEP 5 - 14FT BEAM ASSEMBLY C01 (1) CORBEL- W2A03370 (2) BEAM - W4L14450 1"x5 1/4"x28 1/8" (24x134x714) 1 3/8"x6 7/16"x36 1/4" (36x163x921) C02 (1) G01 CORBEL W/TAG- W2A03371 1 3/8"x6 7/16"x36 1/4" (36x163x921) HAND TIGHTEN ONLY 22
STEP 6 - 14FT BEAM ASSEMBLY (x2) 10FT POST ASSEMBLY (x2) 14FT BEAM ASSEMBLY TIPS: • THREE PEOPLE ARE HELPFUL FOR THIS STEP. • MOVE THE 10FT POST ASSEMBLIES TO THEIR FINAL LOCATION WITH SOMEONE HOLDING EACH ASSEMBLY UPRIGHT. • USING A THIRD PERSON, CONNECT THE 14FT BEAM ASSEMBLY TO THE POSTS TO MAKE THE GAZEBO FRAME.
STEP 7 CRITICAL: SQUARE UNIT BEFORE PROCEEDING TO NEXT STEPS. ONCE SQUARE, TIGHTEN ALL HARDWARE.
STEP 8 - ROOF SUPPORT ASSEMBLY A4M01178 (4) POST CLIP DO NOT OVERTIGHTEN 26
STEP 9 - ROOF SUPPORT ASSEMBLY H18 (1) ROOF SUPPORT- W4L14526 1"x3 3/8"x48" (24x86x1220) A4M01184 PANEL SUPPORT BRACKET (2) INSERT T-NUTS FIRST 27
STEP 10 - ROOF SUPPORT ASSEMBLY H19 ROOF SUPPORT-W4L16212 (4) 1"x3 3/8"x74 7/8" (24x86x1902) REPEAT ON ON OPPOSITE END OF ROOF SUPPORT BOARD INSERT T-NUTS FIRST 28
STEP 11 - ROOF SUPPORT ASSEMBLY A4M01205 METAL SPACER (4) A4M01204 RIDGE PEAK CAP (1) TIPS: • REMOVE PROTECTIVE BLUE FILM BEFORE ASSEMBLY WARNING: GLOVES ARE RECOMMENDED WHEN HANDLING STEEL ROOF PIECES 29
STEP 12 SUPPORT ASSEMBLY • THREE PEOPLE ARE HELPFUL FOR THIS STEP. • POSITION A PERSON ON A LADDER IN THE CENTER OF THE BASE. • LIFT ROOF SUPPORT UP AND OVER THE 14FT SIDE AND INSERT INTO CORNER POST CLIPS.
STEP 13 ROOF SUPPORT ASSEMBLY REPEAT ON ALL POSTS 31
STEP 14 - 14FT ROOF PANEL ASSEMBLY H02 (1) ROOF JOIST- W4L14430 1"x3 3/8"x46 3/4" (24x86x1188) A4M01193 PANEL BRACKET (1) INSERT T-NUTS FIRST HAND TIGHTEN ONLY 32 A4M 01191 PANEL BRACKET 1) (
STEP 15 - 14FT ROOF PANEL ASSEMBLY H01 ROOF JOIST-W4L16213 (1) 1"x3 3/8"x"88 3/16" (24x86x2240) H09 ROOF JOIST-W4L16214 (1) 1"X3 3/8"X88 1/8" (24x86x2240) 33
STEP 16 - 14FT ROOF PANEL ASSEMBLY E02 (2) E11 (1) RAFTER- W4L14434 1 3/8"x3 3/8"x63 7/8" (36x86x1622) E01 RAFTER- W4L14431 E04 RAFTER- W4L14523 (1) RAFTER- W4L14528 1 3/8"x3 3/8"x63 7/8" (36x86x1622) (1) E03 (1) RAFTER- W4L14432 1 3/8"x3 3/8"x20 7/16" (36x86x519) E06 (1) RAFTER - W4L14524 1 3/8"x3 3/8"x20 7/16" (36x86x519) 34 1 3/8"x3 3/8"x44" (36x86x1117) 1 3/8"x3 3/8"x44" (36x86x1117)
STEP 17A - 14FT ROOF PANEL ASSEMBLY Q01 ROOFJOIST-W4L16210 (2) 1"x4 7/16"x84 9/16" (24x112x2148) TIP: • RAFTERS MAY NEED TO BE LOOSENED TO ATTACH Q01 TO H01/H09 35
STEP 17B - 14FT ROOF PANEL ASSEMBLY TIPS: • USING THE Q01 BOARD AS A GUIDE AND A 1/8" DRILL BIT, DRILL PILOT HOLES INTO THE H01 BOARD USING THE DIMENSION BELOW. • REPEAT ON OPPOSITE END WITH H09 BOARD.
STEP 17C - 14FT ROOF PANEL ASSEMBLY TIP: • LOOSEN HARDWARE TO ADJUST FOR SQUARING IF NEEDED CRITICAL: • SQUARE UNIT BEFORE PROCEEDING TO NEXT STEPS. • THE BELOW DIMENSIONS ARE CRITICAL TO THE FINAL ROOF ASSEMBLY. • MEASUREMENTS SHOULD BE WITHIN +/- 1/4". • MEASUREMENTS OUTSIDE OF TOLERANCE WILL LEAD TO THE INABILITY TO ASSEMBLE THE ROOF.
STEP 18 - 14FT ROOF PANEL ASSEMBLY H05 PURLIN-W4L16207 H07 PURLIN-W4L16208 (2) (2) 1"x3 3/8"x59 7/16" (24x86x1509) H08 PURLIN-W4L16209 (1) (1) H17 (1) H04 1"x3 3/8"x 43 11/16" (24x86x1110) H03 1"x3 3/8"x65 1/2" (24x86x1664) (1) PURLIN - W4L14420 1"x3 3/8"x68 3/8" (24x86x1736) PURLIN - W4L14525 1"x1 3/8"x51 3/8" (24x34x1306) TIPS: • ALIGN PURLIN PILOT HOLES WITH RAFTER PILOT HOLES • ATTACH SCREWS FROM THE CENTER AND WORK OUTWARD • H01 AND HO9 BOARDS DO NOT HAVE PILOT HOLES FOR OUTSIDE EDGE SC
STEP 19 - 14FT ROOF PANEL ASSEMBLY A4M01180-1 (1) 29 GA STEEL SHEETING A4M01179 29 GA STEEL SHEETING (1) A4M01177-1 29 GA STEEL SHEETING (1) A4M01175 29 GA STEEL SHEETING (1) A4M0118 1-1 29 GA STEEL SHEETING (1) TIPS: • • • • • REMOVE PROTECTIVE BLUE FILM STARTING IN THE CENTER, PLACE PANELS AS SHOWN BELOW. OVERLAP PANELS BY ONE RIDGE. PANELS SHOULD BE FLUSH WITH PURLIN ENDS AND Q01 ROOF JOIST.
STEP 20 - 14FT ROOF PANEL ASSEMBLY A4M01198 RIDGE CAP CHANNEL (2) TIPS: • POSITION THE RIDGE CAP CHANNEL OVER THE EDGE OF THE ROOF PANELS WITH THE WIDER SIDE OF THE CHANNEL ON THE BOTTOM. • MAKE SURE THE PANELS ARE FULLY SEATED INTO THE CHANNEL. • FLUSH THE TOP OF THE CHANNEL WITH THE TOP OF THE METAL PANELS.
STEP 21 - 14FT ROOF PANEL ASSEMBLY 41
STEP 22 - 10FT ROOF PANEL ASSEMBLY A4M01192 PANEL BRACKET (1) H11 (1) A4M 01194 PANEL BRACKET (1) ROOF JOIST- W4L14438 1"x3 3/8"x15 15/16" (24x86x404) INSERT T-NUTS FIRST HAND TIGHTEN ONLY 43
STEP 23 - 10FT ROOF PANEL ASSEMBLY H12 ROOF JOIST-W4L16215 (1) 1"X3 3/8"X76 3/4" (24x86x1952) H10 ROOF JOIST-W4L16216 (1) 1"x3 3/8"x76 7/8" (24x86x1952) 44
STEP 24 - 10FT ROOF PANEL ASSEMBLY E09 (1) E05 (1) RAFTER- W4L14439 E07 1 3/8"x3 3/8"x55 13/16" (36x86x1417) RAFTER - W4L14442 1 3/8"x3 3/8"x42 3/4" (36x86x1087) (1) E10 (1) RAFTER- W4L14444 1 3/8"x3 3/8"x42 7/8" (36x86x1087) RAFTER- W4L14443 1 3/8"x3 3/8"x21 3/4" (36x86x553) 45 E12 (2) RAFTER - W4L16217 1 3/8"x3 3/8"x21 3/4" (36x86x553)
STEP 25A - 10FT ROOF PANEL ASSEMBLY Q02 ROOF JOIST-W4L16211 (2) 1"x4 7/16"x61 1/2" (24x112x1562) TIP: • RAFTERS MAY NEED TO BE LOOSENED TO ATTACH Q02 TO H12/H10 46
STEP 25B - 10FT ROOF PANEL ASSEMBLY • USING THE Q02 BOARD AS A GUIDE AND A 1/8" DRILL BIT, DRILL PILOT HOLES INTO THE H12 BOARD USING THE DIMENSION BELOW. • REPEAT ON OPPOSITE END WITH H10 BOARD.
STEP 25C - 10FT ROOF PANEL ASSEMBLY TIP: • LOOSEN HARDWARE TO ADJUST FOR SQUARING IF NEEDED CRITICAL: • SQUARE UNIT BEFORE PROCEEDING TO NEXT STEPS. • THE BELOW DIMENSIONS ARE CRITICAL TO THE FINAL ROOF ASSEMBLY. • MEASUREMENTS SHOULD BE WITHIN +/- 1/4". • MEASUREMENTS OUTSIDE OF TOLERANCE WILL LEAD TO THE INABILITY TO ASSEMBLE THE ROOF.
STEP 26 - 10FT ROOF PANEL ASSEMBLY H13 (1) ROOF JOIST - W4L14446 1"x3 3/8"x20 1/4" (24x86x514) H16 (1) H14 (1) H15 PURLIN - W4L14447 1"x3 3/8"x50 1/16" (24x86x1272) PURLIN - W4L14449 1"x3 3/8"x109 3/4" (24x86x2788) TIPS: • ALIGN PURLIN PILOT HOLES WITH RAFTER PILOT HOLES • ATTACH SCREWS FROM THE CENTER AND WORK OUTWARD • H12 AND H10 BOARDS DO NOT HAVE PILOT HOLES FOR OUTSIDE EDGE SCREWS. • USING THE PURLINS AS A GUIDE AND A 1/8" DRILL BIT, DRILL PILOT HOLES INTO H12/H10 BOARDS.
STEP 27 - 10FT ROOF PANEL ASSEMBLY A4M01176-2 29 GA STEEL (1) SHEETING A4M01180-2 29 GA STEEL (1) SHEETING A4M01177-2 29 GA STEEL (1) SHEETING A4M01181-2 29 GA STEEL (1) SHEETING TIPS: • REMOVE PROTECTIVE BLUE FILM • STARTING IN THE CENTER, PLACE PANELS AS SHOWN BELOW. • OVERLAP PANELS BY ONE RIDGE. • PANELS SHOULD BE FLUSH WITH PURLIN ENDS AND Q02 ROOF JOIST. • ONCE SHEETING IS IN PLACE, IT IS RECOMMENDED TO ADD H100833 SCREWS IN THE MIDDLE TO HOLD SHEETING FOR THE NEXT STEP.
STEP 28 - 10FT ROOF PANEL ASSEMBLY A4M01198 RIDGE CAP CHANNEL (2) TIPS: • POSITION THE RIDGE CAP CHANNEL OVER THE EDGE OF THE ROOF PANELS WITH THE WIDER SIDE OF THE CHANNEL ON THE BOTTOM. • MAKE SURE THE PANELS ARE FULLY SEATED INTO THE CHANNEL. • FLUSH THE TOP OF THE CHANNEL WITH THE TOP OF THE METAL PANELS.
STEP 29 - 10FT ROOF PANEL ASSEMBLY 52
STEP 30 - 10FT ROOF PANEL ATTACHMENT TIPS: • THREE PEOPLE ARE HELPFUL FOR THIS STEP. • POSITION A PERSON ON A LADDER IN THE CENTER OF THE GAZEBO TO HELP SUPPORT THE ROOF PANEL. • WITH TWO PEOPLE, WORK THE PANEL UP WITHOUT SLIDING OR DRAGGING, UNTIL IT MEETS THE ROOF SUPPORT FRAME. • MAKE SURE THE ROOF PANEL SLIDES UNDERNEATH THE RIDGE CAP.
STEP 31 - 10FT ROOF PANEL ATTACHMENT TIPS: • IF NECESSARY, USE A LONG SCREWDRIVER OR CLAMPS TO HOLD PANELS IN PLACE. • INSERT BOLTS INTO THE SECOND HOLE FROM THE TOP OF THE H10 & H12 BOARDS.
STEP 32 - 14FT ROOF PANEL ATTACHMENT TIPS: • THREE PEOPLE ARE HELPFUL FOR THIS STEP. • POSITION A PERSON ON A LADDER IN THE CENTER OF THE GAZEBO TO HELP SUPPORT THE ROOF PANEL. • WITH TWO PEOPLE, WORK THE PANEL UP, WITHOUT SLIDING OR DRAGGING, UNTIL IT MEETS THE ROOF SUPPORT FRAME. • MAKE SURE THE ROOF PANEL SLIDES UNDERNEATH THE RIDGE CAP.
STEP 33 - 14FT ROOF PANEL ATTACHMENT TIPS: • IF NECESSARY, USE A LONG SCREWDRIVER OR CLAMPS TO HOLD PANELS IN PLACE.
STEP 34A - ROOF PANEL ATTACHMENT TIPS: • REPEAT STEPS 32 FOR SECOND 14FT ROOF PANEL. • IF NECESSARY USE A LONG SCREWDRIVER OR CLAMPS TO HOLD PANEL IN PLACE.
STEP 34B - ROOF PANEL ATTACHMENT HAND TIGHTEN ONLY 60
STEP 35 - ROOF PANEL ATTACHMENT TIGHTEN ALL THE HARDWARE IN THE ORDER SHOWN BELOW. START AT THE TOP AND WORK YOUR WAY DOWN.
STEP 36 - ROOF ASSEMBLY A4M01228 RAFTER CLIP (14) TIPS: • ATTACH RAFTER CLIPS FIRST WITH 2" BOLTS. • USING THE BRACKET AS A TEMPLATE AND A 1/8" DRILL BIT, DRILL PILOT HOLES FOR THE H100536 SCREWS. • DRILL PILOT HOLES APPROXIMATELY 1/2" DEEP. • NOTE THERE ARE NO RAFTER CLIPS WHERE CORBELS ARE LOCATED.
STEP 37 - ROOF ASSEMBLY A4M01185 CORNER BRACKET (4) 63
STEP 38 - 14FT ROOF TRIM A4M01200 EDGE TRIM LONG (4) A4M01201 (4) A4M01203 EDGE TRIM SHORT (2) TIPS: • • • • START ON THE LEFT SIDE OF A 14FT PANEL. SLIDE EDGE TRIM PIECES TOGETHER AS SHOWN BELOW. MAKE SURE ALL PANELS ARE COVERED BEFORE INSTALLING SCREWS.
STEP 39 - 10FT ROOF TRIM A4M01201 EDGE TRIM SPLICE (2) A4M01200 EDGE TRIM LONG (4) TIPS: • START ON THE LEFT SIDE OF A 10FT PANEL. • SLIDE EDGE TRIM PIECES TOGETHER AS SHOWN BELOW. • MAKE SURE ALL PANELS ARE COVERED BEFORE INSTALLING SCREWS. • INSTALL H100759 SCREWS AS SHOWN.
STEP 40 - ROOF ASSEMBLY A4M01199 CORNER RIDGE CAP (4) TIPS: • SLIDE CORNER RIDGE CAP ONTO ROOF RIDGE CAP CHANNEL AS SHOWN. • DO NOT PUSH ALL THE WAY TO THE TOP. FLUSH WITH CORNER OF GAZEBO AS SHOWN. • REPEAT ON ALL CORNERS.
STEP 41 - GAZEBO ASSEMBLY A4M00950 (8) STEEL POST PLATE STEEL POST A4M00949 ANCHORING (8) PLATE TIPS: • ALL 950 STEEL POST PLATES GO ON THE INSIDES OF THE POSTS AS SHOWN. • ALL 949 STEEL POST ANCHORING PLATES GO ON THE OUTSIDES OF THE POSTS AS SHOWN.
STEP 42 - GAZEBO ASSEMBLY A100241 (1) BYD ID TAG (SMALL) WITHOUT AGES 68
STEP 43 - GAZEBO ASSEMBLY 69
ELECTRICAL ENCLOSURE • FOR ELECTRICAL ENCLOSURE ATTACHMENT, REFER TO THE INSTRUCTIONS INCLUDED WITH THE ELECTRICAL ENCLOSURE KIT. • ELECTRIC ENCLOSURE CAN BE ATTACHED TO ANY POST. • FOLLOW INSTRUCTIONS FOR PROPER ATTACHMENT.
PowerPort™ MANUFACTURED BY: Backyard Discovery 3305 Airport Drive Pittsburg, KS 66762 800-856-4445 Model # 9205413 Wood Post Mounting Instructions 9205413 (x1) H100966 SCREW RAISED HEAD (x4) ELECTRICAL ENCLOSURE 8x1 1/2 2 3/8 in [60 mm] 2 3/8 in [60mm] 966 (x4) 20 1/8 in [512 mm] SCREW - 1 1/2" 413 (x1) ELECTRICAL ENCLOSURE POST 20 1/8 in [512mm] PRE-DRILL 1/8 IN - (3mm) PILOT HOLES USING THE DIMENSIONS PROVIDED. ENSURE THAT CORD END IS NOT WITH-IN 6"- (152mm) OF THE GROUND WHEN MOUNTING.
PowerPort MANUFACTURED BY: Backyard Discovery 3305 Airport Drive Pittsburg, KS 66762 800-856-4445 Model # 9205413 Metal Post Mounting Instructions A4M01292 MOUNTING BRACKET (x2) 9205413 (x1) ELECTRICAL ENCLOSURE H100746 SCREW TAPPING (x4) 10x1 1/4
FCC MARKING: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC INSTRUCTIONS: CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
