Lakewood Wooden Swing Set Model # 2001022 Owner's Manual & Assembly Instructions MANUFACTURED BY: Backyard Discovery 3305 Airport Drive Pittsburg, KS 66762 800-856-4445 WARNING: FOR DOMESTIC USE ONLY. WARNING NOT SUITABLE FOR CHILDREN UNDER 36 MONTHS. SMALL PARTS. average 2 person assembly time assembly time may vary based on skill level For the most up to date assembly manual, to register your set, or to order replacement parts please visit www.backyarddiscovery.
INSTALLATION SERVICES AVAILABLE!* Need a helping hand? Let our team of professionals handle the installation for you! *Installation services are only available to U.S. customers. With Go Con! gure, we bring you 18 years of experience right to your doorstep. We service a wide array of indoor and outdoor recreation products that most consumers don’t have the time or ability to deliver & install themselves.
Owner’s Manual Play Set MISSING A PART? CALL US BEFORE GOING BACK TO THE STORE The store where you made your purchase does not stock parts for this item. If you have assembly questions or you are missing or have damaged parts, please call 1-800-856-4445 you can also visit www.backyarddiscovery.com or e-mail customerservice@backyarddiscovery.
Owner’s Manual Play Set Please read entire booklet completely before beginning the assembly process Please retain these instructions and your receipt for future reference. Keep them in a safe place where you can refer to them as needed. In order to provide you with the most efficient service, it is required that you provide us with the part numbers when ordering parts. For Your Records: Please take time and fill out the information below. This information will be needed for warranty issues.
Owner’s Manual Play Set Operating Instructions and Safety Warnings WARNING: BURN HAZARD • Pay special attention to plastic and metal surfaces as they may be hot enough to cause burns. • Always check the temperature of the product before letting your children play on it. • Remember that the product may cause burns if left in direct sunlight. • Always be aware of the sun and weather conditions, and do not assume that the equipment is safe because the air temperature is not very high.
Owner’s Manual Play Set Positioning Your Playcenter • The playcenter is designed to be installed on a level surface by an adult with an adult helper. Placeinafl at area of your yard to minimize ground preparation. • Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose fill surfacing material washing away during heavy rains. • Place the equipment not less than 6'-7" (2.
Owner’s Manual Play Set APPENDIX A X3.1.3.2 Do not install loose-fill surfacing over hard surfaces such as concrete or asphalt. X3.1.4 Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles — You may be interested in using surfacing other than loose-fill materials – like rubber tiles or poured-in-place surfaces. X3.1.4.1 Installations of these surfaces generally require a professional and are not “do-it-yourself” projects. X3.1.4.2 Review surface specification before purchasing this type of surfacing.
Owner’s Manual Play Set Instructions for Proper Maintenance IT IS IMPORTANT TO CHECK AND TIGHTEN ALL HARDWARE AT THE BEGINNING AND DURING THE SEASON AS THEY MAY LOOSEN DUE TO WOOD EXPANSION AND CONTRACTION. At the beginning of each play season Additional Maintenance • • • • • • • • • Tighten all hardware. Lubricate all metallic moving parts per manufacturer’s instructions. Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing.
Owner’s Manual Play Set Instructions for Proper Maintenance Your Backyard Discovery structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you properly maintain it. About Our Wood Backyard Discovery uses 100% Cedar (C. Lanceolata) wood.
Owner’s Manual Play Set Assembly Tips Protrusion Hazard Incorrect Correct If you see exposed threads and your bolt protrudes beyond the T-Nut you may have over tightened the bolt or used incorrect hardware. If you’ve overtightened, remove the bolt and add washers to eliminate the protrusion. 1/8” Proper Hardware Assembly BOLT Bolt and T-Nut Assembly Tap T-nut into the provided hole. Insert your bolt through the lock washer and insert into the provided hole opposite from the T-Nut.
Owner’s Manual Play Set Assembly Tips ASSEMBLY TIP: Keep and eye out for these boxes which will contain helpful pictures and information making the assembly process as quick and painless as possible. Sorting Wood E1 E2 F1 F2 G1 G2 When removing the wood from the boxes we recommend arranging them by part number before you begin assembly. This will allow for faster assembly and easily identify any parts that may be missing or damaged.
Tools Required for Installation: (These are the tools that are generally required for assembly of our outdoor products. These tools are not included with the outdoor product purchase.
Basic Setup Dimensions Place the set on level ground, not less than 6 ft-7 in [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 6'-7" [2 m] 14'- 1/2" [4.3 m] 6'-7" [2 m] 24'-5" [7.4 m] 11'-3" [3.4 m] 27'-2 1/2" [8.3 m] Safe Play Zone 6'-3 1/2" [1.9 m] Your set has been designed and engineered for children only and for residential use only. A maximum of 150 lbs.
Parts Identification Wood Components (NOT TO SCALE) (1) E1 - FRONT LEFT UPRIGHT - W4L13354 (1) E2 - FRONT RIGHT UPRIGHT - W4L13355 1 3/8"x3 3/8"x81 3/4" (36x86x2076) 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E3 - BACK LEFT UPRIGHT - W4L13356 (1) 1 3/8"x3 3/8"x81 3/4" (36x86x2076) (1) E4 - BACK RIGHT UPRIGHT - W2A02975 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E77 - ANGLE BRACE - W4L13357 (2) (3) 1 3/8"x3 3/8"x73 1/4" (36x86x1862) F71 - STANDARD ANGLE BRACE - W4L13358 1 3/8"x2 3/8"x13" (36x60x330) (2) 1"x3
Parts Identification Wood Components (NOT TO SCALE) H10 - FLOOR SUPPORT - W4L13369 (1) 1"x3 3/8"x40 1/8" (24x86x1018) H11 - ROOF UPRIGHT - W4L13370 (1) 1"x3 3/8"x55 1/4" (24x86x1404) H74 - LEFT UPRIGHT - W4L13371 (1) 1"x3 3/8"x50 3/4" (24x86x1290) H75 - RIGHT UPRIGHT - W4L13372 (1) 1"x3 3/8"x50 3/4" (24x86x1290) (1) H79 - END SUPPORT - W4L13373 1"x3 1/2"x42" (24x86x1072) (1) J1 - DOOR STOP - W4L13374 1"x2 3/8"x2" (24x60x50) (1) K1 - GROUND BOARD - W4L13375 (2) K2 - GROUND BOARD - W4L13376
Parts Identification Wood Components (NOT TO SCALE) L2 - ARCHED ROOF BOARD - W4L13385 (1) 5/8"x4 3/8"x40" (16x112x1016) (2) M1 - END ROOF RAIL - W4L13386 (1) M2 - FLOOR BOARD - W4L13387 5/8"x3 3/8"x41 7/8" (16x86x1064) 5/8"x3 3/8"x41 7/8" (16x86x1064) (2) M3 - WALL BOARD - W4L13388 5/8"x3 3/8"x41" (16x86x1040) M4 - SERVING SHELF SUPPORT - W4L13389 (1) 5/8"x3 3/8"x40 1/8" (16x86x1018) (2) 5/8"x3 3/8"x40 1/8" (16x86x1018) M6 - FLOOR SUPPORT - W4L13391 (1) 5/8"x3 3/8"x40" (16x86x1016) M7 -
Parts Identification Wood Components (NOT TO SCALE) (4) M14 - PICKET - W4L13399 (1) M15 - WALL RAIL - W4L13400 5/8"x3 3/8"x17 3/4" (16x86x452) 5/8"x3 3/8"x16 5/8" (16x86x422) (2) M16 - WINDOW WALL BOARD - W4L13401 (4) M17 - WINDOW WALL BOARD - W4L13402 5/8"x3 3/8"x14" (16x86x356) 5/8"x3 3/8"x6 1/2" (16x86x164) M18 - FLOOR SUPPORT - W4L13403 (1) 5/8"x3 3/8"x40" (16x86x1016) (1) M19 - WALL BOARD - W4L13404 (1) M20 - WALL BOARD - W4L13405 5/8"x3 3/8"x40 1/8" (16x86x1018) 5/8"x3 3/8"x31 3/4"
Parts Identification Wood Components (NOT TO SCALE) (1) (1) N5 - DOOR STOP SUPPORT - W4L13415 5/8"x2 3/8"x4 7/8" (16x60x125) (1) O1 - SAFETY RAIL - W4L13416 (2) Q1 - BENCH SEAT - W4L13417 1"x4 3/8"x40 1/8" (24x112x1018) SB74 - SWING BEAM EXTENDED - W4L13418 2"x5 1/4"x89 1/2" (50x134x2274) (2) (1) 5/8"x1 3/8"x40 1/8" (16x34x1018) T1 - SUPPORT RAIL - W4L13419 1"x1 3/8"x20" (24x34x507) W71 - SWING BEAM SUPPORT - W4L13420 2"x3 3/8"x49 5/8" (50x86x1260) (2) (1) FP1 - FLOOR PANEL - W2A02973 1 1/4"
Parts Identification Hardware (1) BOLT WH 5/16x4 1/2 BLK - H100534 (2) NUT BARREL WH 5/16x1-1/2 BLK - H100193 (4) BOLT WH 5/16x4 1/4 BLK - H100513 (2) BOLT WH 5/16x1/2 - H100115 (2) NUT LOCK 5/16 BLK - H100479 (2) BOLT WH 5/16x2-1/2 BLK - H100194 (13) NUT BARREL WH 5/16x5/8 BLK - H100469 (18) NUT BARREL WH 5/16x7/8 BLK - H100192 (4) BOLT WH 5/16x2-1/4 BLK - H100205 (25) BOLT WH 5/16x2 BLK - H100457 (14) BOLT WH 5/16x1 3/4 BLK - H100378 (2) BOLT HEX 5/16x2-3/4 BLK - H100472 (7) NUT LOCK 5/16 - H10
Parts Identification Hardware (7) SCREW PFH 8x2-1/2 BLK - H100201 (2) WASHER LOCK EXT 8x15 BLK - H100400 (26) SCREW PFH 8x2 1/2 - H100090 (97) WASHER LOCK EXT 8x19 BLK - H100198 (81) SCREW PFH 8x1-1/2 BLK - H100200 (27) WASHER LOCK EXT 12x19 BLK - H100199 (2) SCREW PFH 8x1-1/4 BLK - H100387 (92) SCREW PFH 8x1 1/8 BLK - H100380 (4) WASHER SPLIT 5/16 BLK - H100477 (54) SCREW PFH 8x1 BLK - H100385 (4) SCREW PFH 8x1/2 BLK - H100203 (2) WASHER FLAT 9x18 BLK - H100474 (2) SCREW TAPPING 14x1-1/2 BLK - H100
Parts Identification Accessories (NOT TO SCALE) (1) SL ID (1) E RA IL 8' GR EE N RI GH T- SL ID E A1 00 05 4 (6) QUICK LINK - A100069 RA IL 8' G RE EN LE FT - A1 00 05 5 (2) HAND GRIP GREEN PLASTIC - A100028 (2) ROPE-CHAIN GREEN 33" - A100083 (4) ROPE-CHAIN GREEN 51.
Parts Identification Accessories (NOT TO SCALE) (1) "A" REVISION TAG - A100314 (2) WINDOW (FLAT PACK) - A6P00019 (1) SLIDE BED 8' DARK GREEN - A6P00384 (1) TARP .4x1014x2195 - A6P00381 1/32"x39 7/8"x86 3/8" (.4x1014x2195) (6) L BRACKET 2.
(1) (4) H74 - LEFT UPRIGHT - W4L13371 1"x3 3/8"x50 3/4" (24x86x1290) M104 - LADDER RUNG - W4L13411 1"x3 3/8"x17 1/8" (24x86x434) LADDER ASSEMBLY STEP 1 (8) H74 SCREW PFH 8x2 BLK (8 PLCS) M104 23 SCREW PFH 8x2 BLK
(1) H75 - RIGHT UPRIGHT - W4L13372 1"x3 3/8"x50 3/4" (24x86x1290) LADDER ASSEMBLY STEP 2 (8) H75 SCREW PFH 8x2 BLK (8 PLCS) 24 SCREW PFH 8x2 BLK
(1) M103 - REAR SUPPORT - W4L13410 5/8"x3 3/8"x18 1/4" (16x86x462) LADDER ASSEMBLY STEP 3 M103 SCREW PFH 8x1-1/2 BLK (4 PLCS) (4) 25 SCREW PFH 8x1-1/2 BLK
(1) M102 - ATTACHMENT BOARD - W4L13409 5/8"x3 3/8"x18 1/4" (16x86x462) LADDER ASSEMBLY STEP 4 M102 SCREW PFH 8x1-1/2 BLK (4 PLCS) FLUSH (4) 26 SCREW PFH 8x1-1/2 BLK
(1) (1) M77 - SLIDE BRACE - W4L13407 5/8"x3 3/8"x14 1/4" (16x86x362) - SLIDE BED 8' DARK GREEN - A6P00384 SLIDE ASSEMBLY STEP 1 PLACE 'M77' SLIDE BRACE BOARD 1/4" FROM THE BOTTOM EDGE OF THE SLIDE BED. USING THE BOARD AS A TEMPLATE, MARK WHERE THE PILOT HOLES WILL BE DRILLED. USE A 3/8" DRILL BIT TO DRILL THE PILOT HOLES INTO THE SLIDE BED. ATTACH THE SLIDE BED SUPPORT BOARD USING THE HARDWARE PROVIDED.
(1) EK - SLIDE RAIL 8' GREEN RIGHT - A100054 (2) (1) EL - SLIDE RAIL 8' GREEN LEFT - A100055 M78 - CENTER SLIDE BRACE - W4L13408 5/8"x3 3/8"x14 1/4" (16x86x362) SLIDE ASSEMBLY STEP 2 USING A 1/8" DRILL BIT, DRILL PILOT HOLES IN EACH INDENTATION ALONG EACH SIDE RAIL. THERE SHOULD BE 12 INDENTIONS ON EACH RAIL. PLACE ONE SLIDE RAIL ON FLAT SURFACE. STARTING AT THE BOTTOM, INSERT THE SLIDE BED INTO THE CHANNEL ON THE INSIDE OF THE RAIL.
(1) SB74 - SWING BEAM EXTENDED - W4L13418 2"x5 1/4"x89 1/2" (50x134x2274) (2) L BRACKET 66x66x127 - A100140 (1) SWING BEAM EXTENSION BRACKET-LEFT - A100325 (1) SWING BEAM EXTENSION BRACKET-RIGHT - A100326 SWING BEAM ASSEMBLY STEP 1 BOLT HEX (2) 5/16x2-3/4 BLK NUT BARREL (3) WH 5/16x7/8 BLK WASHER (4) FLAT 8x27 BLK L BRACKET 66x66x127 (2 PLCS) NUT LOCK 5/16 BLK (2 PLCS) WASHER FLAT 8x27 BLK (4 PLCS) BOLT HEX 5/16x2-3/4 BLK (2 PLCS) BOLT WH 5/16x1 3/4 BLK (3 PLCS) SB74 NUT BARREL WH 5/16x7/8 BLK (3
(1) W71 - SWING BEAM SUPPORT - W4L13420 (1) 2"x3 3/8"x49 5/8" (50x86x1260) (2) H79 - END SUPPORT - W4L13373 1"x3 1/2"x42" (24x86x1072) E77 - ANGLE BRACE - W4L13357 1 3/8"x3 3/8"x73 1/4" (36x86x1862) SWING BEAM ASSEMBLY STEP 2 BOLT WH (1) 5/16x4 1/2 BLK NUT BARREL (1) WH 5/16x7/8 BLK BOLT WH (2) 5/16x2-1/4 BLK LAG SCREW (2) WH 5/16x2 BLK WASHER (5) LOCK EXT 8x19 BLK W71 WASHER LOCK EXT 12x19 BLK (1 PLCS) WASHER LOCK EXT 8x19 BLK (1 PLCS) NUT BARREL WH 5/16x7/8 BLK (1 PLCS) BOLT WH 5/16x4 1/2 BL
SWING BEAM ASSEMBLY STEP 3 BOLT WH (2) 5/16x2-1/2 BLK BOLT WH (2) 5/16x1 3/4 BLK NUT BARREL (2) WH 5/16x1-1/2 BLK NUT BARREL (2) WH 5/16x7/8 BLK NUT BARREL WH 5/16x7/8 BLK (2 PLCS) WASHER (2) LOCK EXT 8x19 BLK BOLT WH 5/16x1 3/4 BLK (2 PLCS) WASHER (2) LOCK EXT 12x19 BLK BOLT WH 5/16x2-1/2 BLK (2 PLCS) WASHER LOCK EXT 8x19 BLK (2 PLCS) NUT BARREL WH 5/16x1-1/2 BLK (2 PLCS) WASHER LOCK EXT 12x19 BLK (2 PLCS) 31
(6) 9 1/2" SWING HANGER QUICK LINK - H100099 SWING BEAM ASSEMBLY STEP 4 (6) NUT LOCK 5/16 (6) WASHER FLAT 8x27 WASHER (6) SAFETY 17x30 NUT LOCK 5/16 (6 PLCS) WASHER FLAT 8x27 (6 PLCS) 1. Lock nut must be tightened until loop is tight against the safety washer. 2. Swing hanger bolt must be orientated as shown to avoid damage to swing hanger bolt.
(1) H1 - LEFT ROOF RAIL - W4L13360 (1) H10 - FLOOR SUPPORT - W4L13369 (1) 1"x3 3/8"x60" (24x86x1524) 1"x3 3/8"x40 1/8" (24x86x1018) 5/8"x3 3/8"x47 1/2" (16x86x1205) K1 - GROUND BOARD - W4L13375 5/8"x5 1/4"x59" (16x134x1499) TOP (1) K3 - GROUND BOARD - W4L13377 (2) E3 - BACK LEFT UPRIGHT - W4L13356 1 3/8"x3 3/8"x81 3/4" (36x86x2076) TOP (1) F71 - STANDARD ANGLE BRACE - W4L13358 (1) 1 3/8"x2 3/8"x13" (36x60x330) STEP 1 T-NUT 5/16 BLK (4 PLCS) E1 - FRONT LEFT UPRIGHT - W4L13354 1 3/8"x3 3/
(2) M8 - BRACE - W4L13393 5/8"x3 3/8"x26 5/8" (16x86x676) STEP 2 (6) BOLT WH 5/16x1 BLK WASHER (6) LOCK EXT 8x19 BLK NUT BARREL (6) WH 5/16x5/8 BLK WASHER (6) LOCK EXT 12x19 BLK M8 BOLT WH 5/16x1 BLK (6 PLCS) WASHER LOCK EXT 8x19 BLK (6 PLCS) WASHER LOCK EXT 12x19 BLK (6 PLCS) NUT BARREL WH 5/16x5/8 BLK (6 PLCS) 34
(1) H5 - SWING BEAM RAIL - W4L13364 (1) 1"x3 3/8"x40 1/8" (24x86x1018) (1) O1 - SAFETY RAIL - W4L13416 5/8"x1 3/8"x40 1/8" (16x34x1018) M21 - WALL BOARD - W4L13406 5/8"x3 3/8"x40 1/8" (16x86x1018) STEP 3 LAG SCREW (2) WH 5/16x2 BLK T-NUT 5/16 BLK (2 PLCS) H5 (2) WASHER LOCK EXT 8x19 BLK (2 PLCS) SCREW PFH 8x1-1/2 BLK WASHER (4) LOCK EXT 8x19 BLK BOLT WH 5/16x4 1/4 BLK (2 PLCS) (2) SCREW PFH 8x1-1/2 BLK (2 PLCS) O1 LAG SCREW WH 5/16x2 BLK (2 PLCS) M21 WASHER LOCK EXT 8x19 BLK (2 PLCS) 35 B
(1) (1) H4 - FLOOR SUPPORT - W4L13363 (1) 1"x3 3/8"x40 1/8" (24x86x1018) M4 - SERVING SHELF SUPPORT - W4L13389 (1) 5/8"x3 3/8"x40 1/8" (16x86x1018) (1) (1) STEP 4 H2 - RIGHT ROOF RAIL - W4L13361 1"x3 3/8"x60" (24x86x1524) K4 - GROUND BOARD - W4L13378 5/8"x5 1/4"x40 1/8" (16x134x1018) E2 - FRONT RIGHT UPRIGHT - W4L13355 1 3/8"x3 3/8"x81 3/4" (36x86x2076) E4 - BACK RIGHT UPRIGHT - W2A02975 1 3/8"x3 3/8"x81 3/4" (36x86x2076) H2 LAG SCREW (10) WH 5/16x2-1/2 BLK WASHER (10) LOCK EXT 8x19 BLK H4
(1) M5 - WALL BOARD - W4L13390 (1) 5/8"x3 3/8"x40 1/8" (16x86x1018) M11 - SERVING HEADER - W4L13396 5/8"x3 3/8"x40 1/8" (16x86x1018) STEP 5 LAG SCREW (4) WH 5/16x2 BLK WASHER (4) LOCK EXT 8x19 BLK M5 LAG SCREW WH 5/16x2 BLK (4 PLCS) M11 WASHER LOCK EXT 8x19 BLK (4 PLCS) 37
(2) (1) (1) K2 - GROUND BOARD - W4L13376 M18 - FLOOR SUPPORT - W4L13403 5/8"x3 3/8"x40" (16x86x1016) 5/8"x5 1/4"x60 1/2" (16x134x1538) M6 - FLOOR SUPPORT - W4L13391 5/8"x3 3/8"x40" (16x86x1016) (1) L1 - ARCHED ROOF BOARD - W4L13384 5/8"x4 3/8"x40" (16x112x1016) (1) L2 - ARCHED ROOF BOARD - W4L13385 5/8"x4 3/8"x40" (16x112x1016) STEP 6 (20) BOLT WH 5/16x2 BLK L1 WASHER (20) LOCK EXT 8x19 BLK (20) T-NUT 5/16 BLK L2 NOTE HOLE LOCATIONS M18 M6 T-NUT 5/16 BLK (20 PLCS) WASHER LOCK EXT 8x19 BLK
(1) F71 - STANDARD ANGLE BRACE - W4L13358 1 3/8"x2 3/8"x13" (36x60x330) (1) H3 - FLOOR JOIST - W4L13362 1"x3 3/8"x40 1/8" (24x86x1018) (1) "A" REVISION TAG - A100314 STEP 7 SCREW PWH (2) 8x3/4 BLK LAG SCREW (1) WH 5/16x2-1/2 BLK (4) SCREW PFH 8x2-1/2 BLK (1) BOLT WH 5/16x2 BLK WASHER (2) LOCK EXT 8x19 BLK (1) T-NUT 5/16 BLK BOLT WH 5/16x2 BLK (1 PLC) F71 H3 T-NUT 5/16 BLK (1 PLC) SCREW PFH 8x2-1/2 BLK (4 PLCS) "A" REVISION TAG (1 PLC) SCREW PWH 8x3/4 BLK (2 PLCS) LAG SCREW WH 5/16x2-1/2 BLK (1
(1) (2) M2 - FLOOR BOARD - W4L13387 5/8"x3 3/8"x41 7/8" (16x86x1064) FP1 - FLOOR PANEL - W2A02973 1 1/4"x19 1/8"x41 7/8" (32x485x1064) STEP 8 (39) SCREW PFH 8x1-1/2 BLK SCREW PFH 8x1-1/2 BLK (39 PLCS) FP1 M2 FP1 40
(10) K93 - WALL BOARD - W4L13382 (1) 3/8"x3 3/8"x19 1/2" (11x86x495) K92 - RIGHT WALL BOARD - W4L13381 3/8"x2 3/4"x37 1/2" (11x70x954) STEP 9 (45) 3 11/16 K92 K93 SCREW PFH 8x1 BLK (45 PLCS) 41 SCREW PFH 8x1 BLK
(1) K91 - LEFT WALL BOARD - W4L13380 3/8"x2 3/4"x37 1/2" (11x70x954) STEP 10 (5) SCREW PFH 8x1 BLK K91 SCREW PFH 8x1 BLK (5 PLCS) 42
(1) K5 - SERVING SHELF - W4L13379 (2) 5/8"x5 1/4"x40 1/8" (16x134x1018) H9 - SHELF SUPPORT - W4L13368 1"x3 3/8"x4 1/2" (24x86x114) STEP 11 (5) SCREW PFH 8x1-1/2 BLK (2) SCREW PFH 8x2 1/2 SCREW PFH 8x2-1/2 BLK (2 PLCS) SCREW PFH 8x1-1/2 BLK (5 PLCS) K5 H9 43
(1) (2) N2 - WALL BOARD - W4L13413 (2) 5/8"x2 3/8"x41" (16x60x1040) M12 - WINDOW WALL BOARD - W4L13397 (2) 5/8"x3 3/8"x25" (16x86x634) M3 - WALL BOARD - W4L13388 5/8"x3 3/8"x41" (16x86x1040) M17 - WINDOW WALL BOARD - W4L13402 5/8"x3 3/8"x6 1/2" (16x86x164) STEP 12 (20) SCREW PFH 8x1 1/8 BLK SCREW PFH 8x1 1/8 BLK (20 PLCS) M17 M3 M12 44 N2
FOLD OUTWARD BOTH SIDES AT THIS LOCATION TOP (1) (1) K94 - WINDOW CLEAT - W4L13383 3/8"x1 1/8"x9 7/8" (11x30x252) - WINDOW (FLAT PACK) - A6P00019 STEP 13 (4) SCREW PWH 8x5/8 BLK (4) SCREW PWH 8x3/4 BLK SCREW PWH 8x5/8 BLK (4 PLCS) WINDOW (FLAT PACK) (1 PLCS) SCREW PWH 8x3/4 BLK (4 PLCS) K94 45
(2) N1 - HINGE BOARD - W4L13412 5/8"x2 3/8"x37 3/4" (16x60x958) STEP 14 (8) SCREW PFH 8x1 1/8 BLK (8 PLCS) N1 46 SCREW PFH 8x1 1/8 BLK
(1) M13 - WALL RAIL - W4L13398 5/8"x3 3/8"x19 1/4" (16x86x490) (1) M15 - WALL RAIL - W4L13400 5/8"x3 3/8"x16 5/8" (16x86x422) STEP 15 (2) BOLT WH 5/16x2 BLK WASHER (2) LOCK EXT 8x19 BLK (2) M13 M15 T-NUT 5/16 BLK WASHER LOCK EXT 8x19 BLK (2 PLCS) BOLT WH 5/16x2 BLK (2 PLCS) T-NUT 5/16 BLK (2 PLCS) 47
(1) M5 - WALL BOARD - W4L13390 (1) 5/8"x3 3/8"x40 1/8" (16x86x1018) M19 - WALL BOARD - W4L13404 5/8"x3 3/8"x40 1/8" (16x86x1018) STEP 16 LAG SCREW (4) WH 5/16x2 BLK WASHER (4) LOCK EXT 8x19 BLK M19 M5 WASHER LOCK EXT 8x19 BLK (4 PLCS) LAG SCREW WH 5/16x2 BLK (4 PLCS) 48
(1) (2) N3 - WALL BOARD - W4L13414 (1) 5/8"x2 3/8"x30" (16x60x762) M16 - WINDOW WALL BOARD - W4L13401 5/8"x3 3/8"x14" (16x86x356) (1) M10 - WALL BOARD - W4L13395 5/8"x3 3/8"x30" (16x86x762) (2) M17 - WINDOW WALL BOARD - W4L13402 5/8"x3 3/8"x6 1/2" (16x86x164) (1) M20 - WALL BOARD - W4L13405 - L BRACKET 2.
FOLD OUTWARD BOTH SIDES AT THIS LOCATION (1) (1) K94 - WINDOW CLEAT - W4L13383 3/8"x1 1/8"x9 7/8" (11x30x252) - WINDOW (FLAT PACK) - A6P00019 STEP 18 (4) SCREW PWH 8x5/8 BLK (4) SCREW PWH 8x3/4 BLK WINDOW (FLAT PACK) (1 PLCS) SCREW PWH 8x5/8 BLK (4 PLCS) K94 SCREW PWH 8x3/4 BLK (4 PLCS) 50
(4) M14 - PICKET - W4L13399 5/8"x3 3/8"x17 3/4" (16x86x452) (5) M22 - PICKET - W4L13547 5/8"x3 3/8"x20 1/8" (16x86x512) STEP 19 (36) M22 SCREW PFH 8x1 1/8 BLK (36 PLCS) 3 3/8 10 3/16 3 3/8 3 3/8 3 3/8 M14 1 9/16 51 SCREW PFH 8x1 1/8 BLK
(1) M9 - HANDLE WALL BOARD - W4L13394 5/8"x3 3/8"x31 3/4" (16x86x808) (1) M10 - WALL BOARD - W4L13395 5/8"x3 3/8"x30" (16x86x762) (1) - L BRACKET 2.
(2) M1 - END ROOF RAIL - W4L13386 5/8"x3 3/8"x41 7/8" (16x86x1064) (4) - L BRACKET 2.
(1) M7 - TOP ROOF RAIL - W4L13392 (1) 5/8"x3 3/8"x40" (16x86x1016) (1) H6 - ROOF UPRIGHT - W4L13365 1"x3 3/8"x24" (24x86x610) H11 - ROOF UPRIGHT - W4L13370 1"x3 3/8"x55 1/4" (24x86x1404) STEP 22 BOLT WH (4) 5/16x1 3/4 BLK BOLT WH (4) 5/16x1 1/2 BLK M7 BOLT WH 5/16x1 3/4 BLK (8 PLCS) H6 (5) SCREW PFH 8x1-1/2 BLK (8) H11 T-NUT 5/16 BLK WASHER (8) LOCK EXT 8x19 BLK T-NUT 5/16 BLK (4 PLCS) SCREW PFH 8x1-1/2 BLK (5 PLCS) BOLT WH 5/16x1 1/2 BLK (4 PLCS) WASHER LOCK EXT 8x19 BLK (8 PLCS) 54
(2) G1 - WALL RAIL - W4L13359 (2) T1 - SUPPORT RAIL - W4L13419 1"x1 3/8"x20" (24x34x507) 1"x5 1/4"x22" (24x134x559) STEP 23 (8) SCREW PFH 8x2 BLK (4) SCREW PFH 8x1-1/2 BLK BOLT WH (2) 5/16x1 1/2 BLK WASHER (2) LOCK EXT 8x19 BLK (2) T-NUT 5/16 BLK G1 SCREW PFH 8x1-1/2 BLK (4 PLCS) T1 T-NUT 5/16 BLK (2 PLCS) SCREW PFH 8x2 BLK (8 PLCS) WASHER LOCK EXT 8x19 BLK (2 PLCS) BOLT WH 5/16x1 1/2 BLK (2 PLCS) 55
(1) - TARP .4x1014x2195 - A6P00381 1/32"x39 7/8"x86 3/8" (.
(2) H7 - BENCH UPRIGHT - W4L13366 1"x3 3/8"x15" (24x86x380) STEP 25 (4) BOLT WH 5/16x1 BLK NUT BARREL (4) WH 5/16x7/8 BLK WASHER (4) LOCK EXT 8x19 BLK WASHER (4) LOCK EXT 12x19 BLK H7 WASHER LOCK EXT 8x19 BLK (4 PLCS) BOLT WH 5/16x1 BLK (4 PLCS) WASHER LOCK EXT 12x19 BLK (4 PLCS) NUT BARREL WH 5/16x7/8 BLK (4 PLCS) 57
(2) H8 - SEAT SUPPORT - W4L13367 1"x3 3/8"x8 1/2" (24x86x216) STEP 26 BOLT WH (4) 5/16x1 3/4 BLK (4) T-NUT 5/16 BLK WASHER (4) LOCK EXT 8x19 BLK H8 T-NUT 5/16 BLK (4 PLCS) WASHER LOCK EXT 8x19 BLK (4 PLCS) BOLT WH 5/16x1 3/4 BLK (4 PLCS) 58
(2) Q1 - BENCH SEAT - W4L13417 1"x4 3/8"x40 1/8" (24x112x1018) STEP 27 (8) SCREW PFH 8x1 3/4 BLK SCREW PFH 8x1 3/4 BLK (8 PLCS) Q1 59
(2) - HAND GRIP GREEN PLASTIC - A100028 STEP 28 (2) BOLT WH 1/4x1 BLK WASHER (4) LOCK EXT 6x15 BLK (2) T-NUT 1/4 BLK (2) BOLT WH 1/4x1 1/2 BLK WASHER (2) LOCK EXT 8x15 BLK NUT BARREL (2) WH 1/4x5/8 BLK NUT BARREL WH 1/4x5/8 BLK (2 PLCS) WASHER LOCK EXT 8x15 BLK (2 PLCS) WASHER LOCK EXT 6x15 BLK (2 PLCS) T-NUT 1/4 BLK (2 PLCS) WASHER LOCK EXT 6x15 BLK (2 PLCS) BOLT WH 1/4x1 BLK (2 PLCS) HAND GRIP GREEN PLASTIC (2 PLCS) 60 BOLT WH 1/4x1 1/2 BLK (2 PLCS)
(1) N5 - DOOR STOP SUPPORT - W4L13415 5/8"x2 3/8"x4 7/8" (16x60x125) (1) J1 - DOOR STOP - W4L13374 1"x2 3/8"x2" (24x60x50) STEP 29 (3) SCREW PFH 8x1-1/2 BLK N5 J1 (2) SCREW PFH 8x1-1/4 BLK SCREW PFH 8x1-1/4 BLK (2 PLCS) SCREW PFH 8x1-1/2 BLK (3 PLCS) 61
(1) DR1 - DOOR PANEL - W2A02974 1 1/2"x16 3/8"x36 3/8" (38x416x924) STEP 30 CENTER DOOR TOP TO BOTTOM IN OPENING (11) N1 FLUSH DOOR WITH FRONT SURFACE OF 'N1' BOARDS CENTER DOOR TOP TO BOTTOM IN OPENING DR1 SCREW PFH 8x1-1/2 BLK (11 PLCS) 62 SCREW PFH 8x1-1/2 BLK
(1) LATCHING KNOB WITH SCREWS - A6P00020 STEP 31 KNOB KIT (1 PLC) FACE PLATE (1 PLC) SCREW PFH 8x3/4 (2 PLCS) LATCH (1 PLC) SCREW PFH 8x1 (1 PLC) 63
LADDER ASSEMBLY FINAL ASSEMBLY STEP 1 BOLT WH (2) 5/16x1 1/4 BLK WASHER (2) LOCK EXT 8x19 BLK (2) WASHER LOCK EXT 8x19 BLK (2 PLCS) BOLT WH 5/16x1 1/4 BLK (2 PLCS) 64 T-NUT 5/16 BLK
SWING BEAM ASSEMBLY (1) BYD ID TAG (LARGE) AGES 3-10 - A100164 FINAL ASSEMBLY STEP 2 BOLT HEX 5/16x2 BLK (4 PLCS) (4) WASHER SPLIT 5/16 BLK (4 PLCS) WASHER FLAT 8x27 BLK (4 PLCS) T-NUT 5/16 BLK (4 PLCS) BOLT HEX 5/16x2 BLK WASHER (4) FLAT 8x27 BLK WASHER (4) SPLIT 5/16 BLK BYD ID TAG (LARGE) AGES 3-10 SCREW PFH 8x1/2 BLK (4 PLCS) 65 (4) T-NUT 5/16 BLK (4) SCREW PFH 8x1/2 BLK
SLIDE ASSEMBLY FINAL ASSEMBLY STEP 3 DRILL (3) 7/16" DIA HOLES THROUGH SLIDE BED AND DECK AT LOCATIONS SHOWN. 3 7/8 3 7/8 POST INSTALL SLIDE AGAINST POST AS SHOWN.
(4) QUICK LINK - A100069 (2) SWING SEAT GREEN 22IN - A6P00054 (4) ROPE-CHAIN GREEN 51.25" - A100087 FINAL ASSEMBLY STEP 4 TIGHTEN QUICK LINK NOTE: WHEN HANGING YOUR SWINGS IT IS RECOMMENDED THAT THE BOTTOM OF THE SWING SEAT, WHEN SITTING ON IT, IS LOCATED NO LOWER THAN (35 cm) 13 7/8 INCHES FROM THE GROUND. INSERT CHAIN INTO QUICK LINK ROPE-CHAIN GREEN 51.
(1) TRAPEZE YELLOW - A6P00034 (2) QUICK LINK - A100069 (2) ROPE-CHAIN GREEN 33" - A100083 FINAL ASSEMBLY STEP 5 TIGHTEN QUICK LINK INSERT CHAIN INTO QUICK LINK ROPE-CHAIN GREEN 33" (2 PLCS) TRAPEZE YELLOW (1 PLC) QUICK LINK (2 PLCS) 68
(6) - GROUND STAKE REBAR - A4M00527 FINAL ASSEMBLY STEP 6 (4) TAP IN GROUND STAKES AT AN APPROXIMATE 45° ANGLE AT THE LOCATIONS SHOWN.
