BIG BRUTUS SWINGSET Model # 1952050 Owner's Manual & Assembly Instructions MANUFACTURED BY: Backyard Discovery 3305 Airport Drive Pittsburg, KS 66762 800-856-4445 average 2 person assembly time assembly time may vary based on skill level For the most up to date assembly manual, to register your set, or to order replacement parts please visit www.backyarddiscovery.com SAVE THIS ASSEMBLY MANUAL FOR FUTURE REFERENCE IN THE EVENT THAT YOU NEED TO ORDER REPLACEMENT PARTS.
INSTALLATION SERVICES AVAILABLE!* Need a helping hand? Let our team of professionals handle the installation for you! *Installation services are only available to U.S. customers. With Go Configure, we bring you 18 years of experience right to your doorstep. We service a wide array of indoor and outdoor recreation products that most consumers don’t have the time or ability to deliver & install themselves.
Owner’s Manual Please Read This Before Starting Assembly MISSING A PART? CALL US BEFORE GOING BACK TO THE STORE The store where you made your purchase does not stock parts for this item. If you have assembly questions or you are missing or have damaged parts, please call 1-800-856-4445 you can also visit www.backyarddiscovery.com or e-mail customerservice@backyarddiscovery.
Owner’s Manual Limited Warranty Please read entire booklet completely before beginning the assembly process Please retain these instructions and your receipt for future reference. Keep them in a safe place where you can refer to them as needed. In order to provide you with the most efficient service, it is required that you provide us with the part numbers when ordering parts. For Your Records: Please take time and fill out the information below. This information will be needed for warranty issues.
Owner’s Manual Operating Instructions and Safety Warnings WARNING: BURN HAZARD • Pay special attention to plastic and metal surfaces as they may be hot enough to cause burns. • Always check the temperature of the product before letting your children play on it. • Remember that the product may cause burns if left in direct sunlight. • Always be aware of the sun and weather conditions, and do not assume that the equipment is safe because the air temperature is not very high.
Owner’s Manual Please Read This Before Starting Assembly Positioning Your Playcenter Suggested Playground Surfacing • The playcenter is designed to be installed on a level surface by an adult with an adult helper. Place in a flat area of your yard to minimize ground preparation. • Do not install home playground equipment over concrete, asphalt, packed earth, grass, carpet, or any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user.
Owner’s Manual Please Read This Before Starting Assembly APPENDIX A X3.1.3.2 Do not install loose-fill surfacing over hard surfaces such as concrete or asphalt. X3.1.4 Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles — You may be interested in using surfacing other than loose-fill materials – like rubber tiles or poured-in-place surfaces. X3.1.4.1 Installations of these surfaces generally require a professional and are not “do-it-yourself” projects. X3.1.4.
Owner’s Manual Instructions for Proper Maintenance IT IS IMPORTANT TO CHECK AND TIGHTEN ALL HARDWARE AT THE BEGINNING AND DURING THE SEASON AS THEY MAY LOOSEN DUE TO WOOD EXPANSION AND CONTRACTION. At the beginning of each play season Additional Maintenance • • • • • • • • • Tighten all hardware. Lubricate all metallic moving parts per manufacturer’s instructions. Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing.
Owner’s Manual Assembly Tips ASSEMBLY TIP: Keep and eye out for these boxes which will contain helpful pictures and information making the assembly process as quick and painless as possible. Sorting Parts E1 E2 F1 F2 G1 G2 When removing the wood from the boxes we recommend arranging them by part number before you begin assembly. This will allow for faster assembly and easily identify any parts that may be missing or damaged.
Owner's Manual Tools Required for Installation Icons and their uses you will see throughout this manual You will need to make sure that your assembly is square before tightening your bolts. For proper assembly you will need to ensure that your structure is level before proceeding to the next step. Some steps in the assembly process will require an extra set of hands. Make sure you have a helper available. This icon shows the size of an open ended wrench. Using the wrench as the fraction bar.
Owner's Manual Basic Setup Dimensions & Assembly Notes Selecting the correct location for your play product is improtant for your children's safety and the product's longevity. The safe play area refers to a zone extending 6 ft 7 in. beyond the play product, including the space above the play product. 9'-31 2 " [2.8 m] 9'-63 4 " [2.9 m] • 26'-43 4 " [8.0 m] 13'-23 4 " [4.0 m] 22'-91 4 " [6.9 m] 6'-7" [2.0 m] Ground Dimension 13' - 1 1/2" (4.0m) x 9' - 5" (2.9m) x 9' - 5 3/4" (2.
Hardware Components Parts Identification H100366 BOLT WH WZ (x4) 5/16x4 H100811 BOLT CARRIAGE WZ (x9) 5/16x2 3/4 H100591 BOLT CARRIAGE WZ (x22) 5/16x2-1/2 H100818 BOLT HEX WZ (x7) M12x 45mm H100499 NUT BARREL WH WZ (x34) 5/16x7/8 H100819 LOCK NUT WZ (x7) M12 H100278 WASHER FLAT WZ (x4) 5/16 A100041 TORX WRENCH (x2) T-40 A100042 TORX BIT (x2) T-40
Accessories (Not to Scale) Parts Identification A4M01013 BOTTOM LEG (x4) A4M01014 MIDDLE LEG (x4) A4M01015 TOP LEG (x4) A4M01016 (x1) MIDDLE TOP BEAM A4M01018 (x2) A4M01019 (x16) SIDE BAR METAL BRACKET GREY A4M01020 LEG CONNECTING TUBE (x8) A4M01021 (x2) A4M01024 (x4) SIDE TOP BEAM A4M01022 (x2) TOP BEAM CONNECTING TUBE METAL BRACKET GREEN
Accessories (Not to Scale) Parts Identification A6P00375 BYD TAG STICKER (SMALL) (x1) A6P00366 (x4) SWING SET FOOT A6P00374 (x1) A4M01044 (x6) WARNING LABEL STICKER A4M00927 QUICK LINK SD (x4) CARABINER SD A4M01041 (x4) A4M00508 6' TRAPEZE ASSEMBLY (x1) (x6) DUCTILE HANGER WZ CHAIN GREEN 7mm x 2028 mm A6P00373 (x2) A4M01040 26" HD BELT SWING A100178 (x4) METAL GROUND STAKE BROWN
STEP 1 Phase 1 A4M01013 (x4) BOTTOM LEG H100591 BOLT CARRIAGE WZ (x12) 5/16x2-1/2 A4M01020 (x8) A4M01014 (x4) H100811 BOLT CARRIAGE WZ (x4) 5/16x2 3/4 MIDDLE LEG A4M01015 (x4) LEG CONNECTING TUBE TOP LEG A4M01019 (x16) METAL BRACKET GREY H100499 NUT BARREL WH WZ (x16) 5/16x7/8 NOTE: REPEAT THIS STEP 4 TIMES. TIP: PLACE CARRIAGE BOLT BEFORE NUT BARREL.
STEP 2 Phase 1 A4M01022 (x2) A4M01016 (x1) TOP BEAM CONNECTING TUBE MIDDLE TOP BEAM A4M01040 (x6) H100811 BOLT CARRIAGE WZ (x4) 5/16x2 3/4 DUCTILE HANGER WZ H100818 BOLT HEX WZ (x6) M12x 45mm A4M01021 (x2) SIDE TOP BEAM A4M01044 (x6) A4M01024 (x4) CARABINER SD H100499 NUT BARREL WH WZ (x4) 5/16x7/8 METAL BRACKET GREEN A6P00375 BYD TAG STICKER (SMALL) (x1) H100819 LOCK NUT WZ (x6) M12 024 (x4) 022 (x2) METAL BRACKET GREEN TOP BEAM CONNECTING TUBE 016 (x1) MIDDLE TOP BEAM 375 (x1) BYD TAG
STEP 1 Phase 2 H100591 BOLT CARRIAGE WZ (x8) 5/16x2-1/2 A6P00374 (x1) WARNING LABEL STICKER H100499 NUT BARREL WH WZ (x8) 5/16x7/8 A4M01018 (x2) SIDE BAR 499 (x8) NUT BARREL - 7/8 TOP BAR ASSEMBLY 591 (x8) BOLT - 2-1/2 PLACE WARNING TAG STICKER CENTERED ON LEG AS SHOWN.
STEP 2 Phase 2 A4M01041 (x4) A6P00373 (x2) CHAIN GREEN 7mm x 2028 mm 26" HD BELT SWING A4M00508 6' TRAPEZE ASSEMBLY (x1) A4M00927 QUICK LINK SD (x4) 041 (x4) CHAIN GREEN 7mm x 2028 mm 927 (x4) QUICK LINK SD 373 (x2) 26" HD BELT SWING 508 (x1) 6' TRAPEZE ASSEMBLY
Phase 2 STEP 3 H100366 BOLT WH WZ (x4) 5/16x4 H100278 WASHER FLAT WZ (x4) 5/16 A6P00366 (x4) SWING SET FOOT A100178 (x4) METAL GROUND STAKE BROWN H100499 NUT BARREL WH WZ (x4) 5/16x7/8 499 (x4) NUT BARREL - 7/8 NOTE HOLE ORIENTATION 366 (x4) BOLT - 4 278 (x4) 178 (x4) METAL GROUND STAKE BROWN WASHER FLAT - 5/16 366 (x4) SWING SET FOOT
