Installation guide

ManualsBrandsB-Tech ManualsProjector MountsBT881

BT881

UNIVERSAL PROJECTOR CEILING MOUNT

INSTALLATION GUIDE & PARTS LIST

This Pack Contains 1 Mount

B-TECH AUDIO VIDEO MOUNTS

www.btechavmounts.com

CONTENTS

INSTALLATION TOOLS REQUIRED

FEATURES

Crosshead

screwdriver

Drill

8mm (5/16") masonry bit

or 5mm (3/16") wood bit

Pencil

Stud finder

(optional)

Installation Safety Notes.....................................................................................................................2

Parts List.............................................................................................................................................4

Installation Instructions.......................................................................................................................6

Product Dimensions..........................................................................................................................14

B-Tech Contact Details.....................................................................................................................16

PLEASE KEEP THIS FOR FUTURE REFERENCE

13mm (1/2") &

10mm (2/5")

spanner or socket

● Suitable for projectors up to 10kg (22lbs)

● Mounts projector only 115mm (4.5") from ceiling or 280mm (11")

with supplied extension rod

● +/-90º tilt adjustment, +/-90º roll adjustment and 360º swivel

● Easy to adjust and fix projector in position

● Steel safety wire for extra security

● Maximum distance between any two fixing points

on projector: 340mm (13.4")

● Suitable for projectors with M2.5, M3, M4, M5 and M6 fixings

● Simple installation with all mounting hardware included

REG. DESIGN NO: 3016251

Summary of content (16 pages)

PAGE 1
BT881 UNIVERSAL PROJECTOR CEILING MOUNT INSTALLATION GUIDE & PARTS LIST This Pack Contains 1 Mount PLEASE KEEP THIS FOR FUTURE REFERENCE FEATURES ● ● ● ● ● ● ● ● Suitable for projectors up to 10kg (22lbs) Mounts projector only 115mm (4.
PAGE 2
INSTALLATION SAFETY INSTRUCTIONS CAUTION: This ceiling mount is intended for use only with the maximum weights indicated. Use with projectors heavier than the maximum indicated may result in instability causing possible injury. Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference.
PAGE 3
CS Společnost B-Tech International Ltd. doporučuje provést instalaci tohoto produktu prostřednictvím odborného instalátora AV či jinak způsobilé osoby. Společnost B-Tech International Ltd, její distributoři a prodejci nenesou odpovědnost za škody nebo zranění způsobená nevhodnou instalací. Tento výrobek je nutno umístit do vhodné konstrukce a používat jen po uvedenou maximální výšku. DE B-Tech International Ltd.
PAGE 4
BT881 PARTS LIST 7 Suitable for loads up to 10kg (22lbs) 9 1 7 5 11 2 Ceiling Plate Assembly 12 3 4 8 16 6 Interface Assembly 18 13 14 10 15 4 17 16
PAGE 5
A B F C D G E H I J REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 REF A B C D E F G H I J REF A1 A2 A3 PART NAME CEILING PLATE SPACER BALL JOINT SHORT EXTENSION ROD LONG EXTENSION ROD ADAPTOR COVER PLATE (FOR PART 1) SECURITY CABLE M8 NUT M8 SPRING WASHER M6 X 6mm GRUB SCREW M6 X 10mm GRUB SCREW CAROUSEL LONG LEG SHORT LEG CAROUSEL COVER PLATE M8 X 20mm HEX SCREW THUMB WHEEL M6 DOME NUT M6 X 11mm SPACER (FOR PART 19) 3mm HEX KEY (FOR PARTS 11 & 12) 5mm HEX KEY (FOR PART 17) INTERFAC
PAGE 6
INSTALLATION INSTRUCTIONS 1 Loosen the grub screws, take the adaptor and cover plates off the ceiling plate. 7 1 12 12 7 21 6 OPTIONAL - LONG CEILING DROP i. Disassemble, remove short extension rod ii.
PAGE 7
2 i. Fix ceiling plate to the ceiling. A3 ONLY USE PART A3 WHEN FIXING TO CONCRETE CEILINGS A2 1 A1 ii. Slide on the cover plates.
PAGE 8
3 Attach interface assembly to projector. i. Attach legs to projector.
PAGE 9
ii. Attach the adaptor to carousel and place on legs. 6 13 10 17 22 iii. Attach the carousel to the legs. Using quick release hand wheels or using secure dome nuts and spacers.
PAGE 10
4 Attach the projector to the ceiling plate assembly and secure with parts 12.
PAGE 11
5 Attach the security cable. i. Un-screw one interface screw to attach security cable. 8 ii. Loop the security cable over the leg.
PAGE 12
iii.
PAGE 13
6 Adjusting the projector. To tilt/roll and swivel, loosen parts 11, adjust and re-tighten. 21 90° 11 360° 7 16 Slide cover plates onto interface assembly.
PAGE 14
BT881 PRODUCT DIMENSIONS 92mm 3.6" O12mm (0.5") 14 280mm 11" 16mm 0.6" 115mm 4.5" 50mm 2" THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
PAGE 15
BT881 PRODUCT DIMENSIONS 45mm 1.8" 6.5mm 0.3" CEILING PLATE 88mm 3.5" 14.5mm 0.6" 45mm 1.8" 59mm 2.3" 74mm 2.9" 340mm 13.4" INTERFACE PLATE 340mm 13.4" THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
PAGE 16
www.btechavmounts.com B-TECH AUDIO VIDEO MOUNTS HEAD OFFICE Bennett House, Long March, Daventry, Northants., NN11 4NR, UK Email: info@btechavmounts.co.uk EUROPE Brixtonlaan 32, Zaventem 1930, Brussels, Belgium Email: info@btechproav.com NORTH AMERICA 203 Eggert Road, Buffalo, NY 14215, USA Email: info@btechavmounts.com SINGAPORE Ruby Industrial Complex, Singapore 347740 Email: info@btechavmounts.com.sg ©2010 Bennett Technologies Limited. All rights reserved.