Specifications

ManualsBrandsB&T ManualsElectronicsWi-Fi Module

Table Of Contents

ESP-12K Specification V1.0

ESP-12K SPECIFICATION

Version V1.0

Summary of content (21 pages)

PAGE 2
ESP-12K Specification V1.0 Disclaimer and copyright notice The information in this article, including the URL for reference, is subject to change without notice. The document is provided "as is" without any guarantee responsibility, including any guarantee of marketability, suitability for a specific purpose or non-infringement, and any guarantee mentioned elsewhere in any proposal, specification or sample.
PAGE 4
ESP-12K Specification V1.0 CONTENT 1.PRODUCT DESCRIPTION..........................................................................................................................V 2.ELECTRICAL PARAMETER.......................................................................................................................IX 3.DIMENSION...................................................................................................................................................XI 4.PIN DEFINITION..........
PAGE 5
ESP-12K Specification V1.0 1.PRODUCT DESCRIPTION ESP-12K is a Wi-Fi module developed by Ensink Technology. The core processor ESP32-S2 of this module is a highly integrated low-power Wi-Fi system-on-chip (SoC) designed for the Internet of Things (IoT) , Mobile devices, wearable electronic devices, smart home and other applications. ESP32-S2 has industry-leading low-power performance and RF performance, supports IEEE802.
PAGE 6
ESP-12K Specification V1.0 Features  Complete 802.
PAGE 7
ESP-12K Specification V1.
PAGE 8
ESP-12K Specification V1.0 Interface UART/GPIO/ADC/PWM/SPI/I2C/LCD/I2S/Camera/IR/USB/DA C IO port qty 37 Serial rate Support 110 ~ 4608000 bps ，default 115200 bps Safety WEP/WPA-PSK/WPA2-PSK SPI Flash Default 32Mbit PSRAM Optional without PSRAM or 8MByte PSRAM Copyright © 2019 Shenzhen Ai-Thinker Technology Co.
PAGE 9
ESP-12K Specification V1.0 2.ELECTRICAL PARAMETER Parameter Min Typical Max Unit VDD 3.0 3.3 3.6 V VIL/VIH - -0.3/0.75VIO - 0.25VIO/3.6 V VOL/VOH - N/0.8VIO - 0.1VIO/N V IMAX - - - 12 mA Voltage I/O Condition RF performance Description Work frequency Typical Unit 2400 - 2483.
PAGE 10
ESP-12K Specification V1.0 Power consumption The following power consumption data is based on a 3.3V power supply, an ambient temperature of 25 ° C, and is measured using an internal voltage regulator.  All measurements are done at the antenna interface without SAW filters.  All transmission data is based on a 90% duty cycle, measured in continuous transmission mode. Mode Mix Typical Max Unit Send 802.11b, CCK 11Mbps, POUT=+17dBm - 190 - mA Send 802.
PAGE 12
ESP-12K Specification V1.0 4.PIN DEFINITION The ESP-12K module has a total of 42 interfaces, such as the pin diagram, the pin function definition table is the interface definition ESP-12K PIN definition diagram List PIN function definition No.
PAGE 13
ESP-12K Specification V1.
PAGE 14
ESP-12K Specification V1.0 33 IO39 MTCK, GPIO39, CLK_OUT3 34 IO40 MTDO, GPIO40, CLK_OUT2 35 IO41 MTDI, GPIO41, CLK_OUT1 36 IO42 MTMS, GPIO42 37 U0TX U0TXD, GPIO43, CLK_OUT1 38 U0RX U0RXD, GPIO44, CLK_OUT2 39 IO45 GPIO45 40 IO46 GPIO46 41 EN 42 GND High level: chip enable; Low level: the chip is off; Has been raised by default.
PAGE 16
ESP-12K Specification V1.0 6.DESIGN GUIDE 1、Application circuit note: (1) The RC delay circuit needs to be added to the EN pin. It is recommended that R = 10kΩ and C = 0.1μF; (2) GPIO18 as U1RXD needs to add a pull-up resistor externally. 2、Antenna layout requirements (1) The following two methods are recommended for the installation location on the motherboard: Option 1: Place the module on the edge of the main board, and the antenna area protrudes from the edge of the main board.
PAGE 17
ESP-12K Specification V1.0 3、Power supply (1) 3.3V voltage is recommended, the peak current is more than 500mA (2) It is recommended to use LDO for power supply; if using DC-DC, it is recommended to control the ripple within 30mV. (3) It is recommended to reserve the position of the dynamic response capacitor in the DC-DC power supply circuit, which can optimize the output ripple when the load changes greatly. (4), 3.3V power interface is recommended to add ESD devices.
PAGE 19
ESP-12K Specification V1.0 7.PACKAGING As shown below, the packaging of ESP-12K is taping. 8.CONTACT US Website：https://www.ai-thinker.com Development DOCS：https://docs.ai-thinker.com Official forum：http://bbs.ai-thinker.com Sample purchase：https://aithinker.onesite.alibaba.com/ Business：sales@aithinker.com Technical support：support@aithinker.
PAGE 20
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules The ESP-12K is an Wi-Fi Module with digitally modulated systems using an DSSS with DBPSK/DQPSK/CCK for 802.11b; OFDM with BPSK/QPSK/16QAM/64QAM for 802.11g/n; modulation. It operates on the 2400-2483.5MHz band and, therefore, is within U.S. FCC part 15.247 standard 2.3 Specific operational use conditions The EUT is a Wi-Fi Module Operation Frequency: 2412-2462MHz for 802.
PAGE 21
2.10 Additional testing, Part 15 Subpart B disclaimer The module without unintentional-radiator digital circuit, so the module does not required an evaluation by FCC Part 15 Subpart B. The host should be evaluated by the FCC Subpart B.