Datasheet
Programmable AC Power Source
9830B Series
6
www.bkprecision.com
v071520
Specifications
Model 9832B 9833B
AC Output
Output Phase Single
Maximum Power 2000 VA 3000 VA
Voltage
Range
1
(rms)
Low 0 to 150 V
High 0 to 300 V
Current (rms)
Low 20 A 30 A
High 10 A 15 A
Current (peak)
Low
65 A (< 100 Hz)
50 A (> 100 Hz)
97.5 A (< 100 Hz)
75 A (> 100 Hz)
High
32.5 A (< 100 Hz)
25 A (> 100 Hz)
48.75 A (< 100 Hz)
37.5 A (> 100 Hz)
Frequency
Range
Single phase 45 Hz to 1.2 kHz
3-Phase 45 Hz to 600 Hz
Phase Range 0 to 359.7 º
Total
Harmonic
Distortion
2
45 Hz to 400 Hz 0.5 %
> 400 Hz to 1 kHz 1 %
> 1 k to 1.2 kHz 2 %
Line Regulation
3
0.1 %
Load Regulation
3
0.1 %
Temp. Coefficient 0.2 % per ºC
Crest Factor
45 Hz to 100 Hz 3.25
100 Hz to 1.2 kHz 2.5
Efficiency
4
80 % (typical)
DC Output
Maximum Power 1000 W 1500 W
Voltage
Range
1
Low 0 to ± 212 V
High 0 to ± 424 V
Current
Low 10 A 15 A
High 5 A 7.5 A
Ripple and Noise (20 Hz to 20 MHz) ≤ 300 mVrms / ≤ 3 Vpp
Output Characteristics
Transient Response Time 1.5 ms (typical)
Output Impedance ≤ 1 Ω
Programming
Resolution
Voltage 0.1 V
Phase 0.1 º
Frequency 0.01 Hz (< 100 Hz), 0.1 Hz (> 100 Hz)
Accuracy
Voltage
AC 0.2 % + 0.2 % F.S.
DC 0.2 % + 0.4 % F.S.
Phase 0.15 %
Frequency ± 1 % (45 Hz to 100 Hz)
Note: All specifications apply to the unit after a temperature stabilization time of 15 minutes over an
ambient temperature range of 23 °C ± 5 °C.
1 - The maximum voltage is limited to 310 Vrms and ± 438 Vdc, 3 Phase mode not supported
2 - > 66% to full range
3 - AC mode with sine wave and remote sense enabled
4 - 150 VAC (150 V range) and 300 VAC (300 V range) with nominal input AC voltage.
5 - Analog programming pin available on digital I/O connector, not available in 3-Phase
Measurement
Resolution
Voltage 0.1 V
Current 0.01 A
Power 0.01 W
Frequency
0.01 Hz (< 100 Hz)
0.1 Hz (> 100 Hz)
Accuracy
Voltage
AC 0.25 % + 0.25 % F.S.
DC 0.25 % + 0.5 % F.S.
Current
AC
0.25 % + 0.375 % F.S. (rms)
0.4 % + 0.75 % F.S. (Peak)
0.25 % + 0.25 % F.S. (rms)
0.25 % + 0.5 % F.S. (Peak)
DC 0.25 %+3 % F.S 0.25 %+2% F.S
Power
1 % of F.S. for frequency ≤ 500 Hz
2 % of F.S. for frequency > 500 Hz
Frequency 0.5 %
AC Input
Voltage 190 V to 250 V
Frequency 47 Hz to 63 Hz
Maximum Power 2500 VA 3800 VA
Maximum Current 13.2 A 20 A
Power Factor 0.98 (typical)
General
Analog
BNC Input
Input
Voltage Range
0 to ± 12.5 V
Input Impedance 200 kΩ
Bandwidth 1.2 kHz
Storage Memory
10 programs, up to 100 steps total (List mode)
5 memory locations for user-defined waveforms
9 instrument settings
Remote Interface
Analog programming
5
, USB (USBTMC or virtual COM),
RS232
5
,
GPIB, and Ethernet
Command Response time 50 ms
Protection OVP, OCP, OPP, OTP
Operating Temperature 32 °F to 104 °F (0 °C to 40 °C)
Storage Temperature -40 °F to 185 °F (-40 °C to 85 °C)
Environmental Conditions ≤ 80% Relative Humidity up to 35 ºC, non-condensing
Dimensions (W x H x D) 16.5” x 5.2” x 22” (420 x 132 x 560 mm)
Weight 52.9 lbs (24 kg)
Warranty 3 Years
Included Accessories
AC power cord with input connector, test report &
certificate of calibration
Optional Accessories
Rackmount ears with handles (RK3U) &
3-Phase sync adapter (TL983P), 3-Phase kit (TL983P-KIT)
For the most current user manual visit: bkprecision.com
Unterminated AC power cord
(Standard)
Rackmount ears with handles
RK3U (Optional)
3-Phase sync adapter
TL983P (Optional), 3-Phase kit
TL983P-KIT (Optional)
9830B Series Accessories