Install guide

ManualsBrandsB&D ManualsGarage Door OpenerControll-A-Door P

Sectional Door Opener SDO 2V2 Tri-Tran

Installation Instructions

Controll-A-Door

Diamond

Kit Contents

1. 1 x SDO-2 drive unit

2. 1 x Wall mount transmitter with battery and screws

3. 2 x Transmitters and batteries

4. 1 x Bent arm door attachment

5. 1 x Straight arm door attachment

6. 1 x Wall bracket TS01

7. 1 x Door bracket Locator

8. 1 x Door bracket

9. 3 x Pin Snap SSP 8 ZNU 31080

10. 2 x Hex Head screw M8x25

11. 1 x Pin 0890

12. 2 x Clevis Pin 0829

13. 2 x Hex Serration flange nut M8

14. 4 x Hex flange screw taptite ‘S’ M4 x 10

15. 1 x KPX-7 Wireless Keypad

PLUS

16. 2 x Track Bracket

17. 1 x Pre-Assembled Single Piece C-Rail

Power Supply

Properly earthed 3 pin single -phase power is required.

Head Room

The minimum height required between the highest point

of the door’s travel and the ceiling is 57mm.

WARNING! A portable power generator is

not recommended due to spikes, surges and

fluctuations in the supply.

Important Safety Instructions

Locate shaft into

sprocket

Shaft

Hex flange screw taptite

‘S’ M4 x 10

Track bracket (x2)

Quick Install Guide

C-Rail Attachment

Single piece

C-Rails are pre-tensioned during

manufacturing for transport. Some

extra tension may be required after

installation.

If the C-Rail needs to be shortened

or lenghtened (using the extension

kit) ensure these modifications are

made to the drive unit end.

To prevent scratching the unit after

attaching the C-Rail, place the drive

unit back in its packing box.

Open to Determine your

Door Type

To Increase Force Pressure

a. Hold down the FORCE MARGIN SET

button.

b. While holding the FORCE MARGIN SET

button, press the PLUS (+) button. Each

press will increases the force margin.

c. The OPEN LIMIT LED will flash each time

the PLUS (+) button is pressed to indicate

an increase in force.

d. If the OPEN LIMIT LED flashes

continuously when the PLUS (+) button

is being pressed, this indicates that

the maximum force setting has been

reached.

e. Test the force again as per Testing Close

Cycle and Testing Open Cycle.

To Recall Factory Set Force

a. Holding down the FORCE MARGIN SET

button and the LIMIT SET button for two

seconds.

b. Release both buttons. The default setting

should now be recalled.

Doc # 161009_00

Part # 79122

Released: 28/03/14

WARNING!

• The door may operate unexpectedly, therefore do not allow anything to stay in the path of

the door.

• When operating the manual release while the door is open, the door may fall rapidly due

to weak or broken springs, or due to being improperly balanced.

• The drive must not be used with a door incorporating a wicket door, unless the drive cannot

be operated with the wicket door open.

• The drive is intended to be installed at least 2.5m above the floor.

• Do not disengage the opener to manual operation with children/persons or any objects

including motor vehicles within the doorway.

• If the door is closing and is unable to re-open when obstructed, discontinue use. Do not

use a door with faulty obstruction sensing

• When using auto close mode, a Photo Electric beam must be fitted correctly and tested

for operation at regular intervals. Extreme caution is recommended when using auto

close mode. All safety rules must be followed.

ELECTROCUTION!

• Place opener in protected area so that it does not get wet.

• Do not spray with water .

• Disconnect the power cord from mains power before making any repairs or removing

covers. Only experienced service personnel should remove covers from the opener.

• If the power supply cord is damaged, it must be replaced by an Automatic Technology

service agent or suitably qualified person.

• Connect the opener to a properly earthed general purpose 240V mains power outlet

installed by a qualified electrical contractor.

CAUTION:

Emergency Access • If garage has no pedestrian entrance door, an emergency access device should be

installed. This accessory allows manual operation of the garage door from outside in case

of power failure.

Muscular strain • Practice correct lifting techniques (carton weighs approx 9kgs)

• Practice correct lifiting techniques when required to lift the door as per installation instructions.

Fall from ladder • Ensure ladder is the correct type for job.

• Ensure ladder is on flat firm ground that will take the weight without the legs sinking.

• Ensure user has 3 points of contact while on ladder.

Crush injury from unsecured

door

• Place a 2 metre exclusion zone around area under the door while it is unsecured.

• Do not move under a door while it is on the door support (or ladder)

• Follow the installation instructions

• Fit door support (or ladder) snugly under door before removing bracket.

• Ensure door support (or ladder) is on flat ground

Garage Door • Examine the door installation, in particular cables, springs and mountings for signs of wear,

damage and imbalance.

• The garage door must be well balanced. Sticking or binding doors must be repaired by a

qualified garage door installer prior to installation of the opener.

• Remove or disengage all garage door locks and mechanisms prior to installation of the

opener.

Entanglement • Never plug in and operate opener prior to installation.

• Keep hands and loose clothing clear of door and guides at all times.

Entrapment under

operating door

• DO NOT operate the opener unless the garage door is in full view and free from objects

such as cars and children/people. Make sure that the door has finished moving before

entering or leaving the garage

• In order for the opener to sense an object obstructing the door way, some force must be

exerted on the object. As a result the object, door and/or person may suffer minor damage

or injury.

• Ensure the garage door is in good working order by undertaking regular servicing.

• Install the optional wall transmitter in a location where the garage door is visible, but out

of the reach of children at a height of at least 1.5m.

• Photo Electric beams must be installed if the closing force at the bottom edge of the door

exceeds 400N (40kg)

This automatic garage door opener is designed and tested to offer safe service provided it is

installed and operated in strict accordance with the following safety rules. Failure to comply with

the following instructions may result in death, serious personal injury or property damage.

34-36 Marigold St, Revesby, NSW, Australia ABN 25 010 473 971

P: 13 62 63 W: www.bnd.com.au

WARNING! Take care when testing or adjusting the

Safety Obstruction Force. Excessive force may cause

SERIOUS PERSONAL INJURY and/or PROPERTY

DAMAGE.

Testing Close Cycle

a. Press the programmed transmitter to open the door.

b. Place a piece of timber approximately 40mm high on the

floor directly under the door.

c. Press the programmed transmitter to close door.

d. The door should strike the object and re-open.

Testing Open Cycle

a. Press the transmitter to close the door.

b. Press again to open the door.

c. When the door reaches approximately half way, firmly grab

the door’s bottom rail - the door should stop.

d. If the door does not reverse readily when closing, or stop

when opening, the force may be excessive and need

adjusting.

40mm block of wood

WARNING! If the door fails these tests, put the opener into

manual mode, only operate the door by hand and call for

service.

WARNING! Photo electric beams must be installed if the closing

force at the bottom edge of the door exceeds 400N (40kg) force.

NOTE: Once the travel limits are set and safety obstruction force tested check the chain or belt tension. As per the sticker on the C-rail the chain

or belt should sag slightly, so there is a 5mm gap between the bottom of the C-rail and the chain or belt.

The tension can be varied by using a spanner to adjust the bolt at the door end of the C-rail.

Be sure not to over-tension the chain or belt as this can cause damage to the C-rail or opener.

Adjusting Safety Obstruction Force

The Safety Obstruction Force is calculated automatically during setup. Adjusting this is normally only necessitated by environmental conditions

such as windy or dusty areas, and areas with extreme temperature changes.

Symptom Possible cause Remedy

The opener does not work

from the transmitter

Garage door in poor condition e.g. springs

may be broken

The opener does not have power

The battery in the transmitter is flat

Transmitter does not contain

Tri-Tran

Technology

The opener has been put into “Vacation

Mode”

The transmitter button is not programmed to

operate the door.

Door Code LED is flashing yet the opener is

not working.

Check the door’s operation

Plug a device of similar voltage (e.g. a hairdryer) into the

power point and check that it is OK

Replace the battery

Check that the transmitter has grey buttons and the model

number on the back displays V2. Contact dealer for support

if otherwise.

Turn off “Vacation Mode”

(Section 8.3, step e of Home Owners Manual)

Code in the transmitter

Ensure the correct button on the transmitter is being

pressed.

One transmitter works but

the other/s do not

Faulty transmitter

Flat battery

Replace transmitter

Replace battery

The chain moves but the

door remains stationary

The opener is disengaged Re-engage the opener

Motor is running but chain is

not moving

Damage motor assembly Contact your dealer for support.

The transmitter range varies

or is restricted

Variations are normal depending on

conditions e.g. temperature or external

interference

The battery life is exhausted

Position of the transmitter in the motor

vehicle

Make sure you can see the door when you use the

transmitter.

Check the battery status by pressing a button (flashing or no

light requires battery to be changed)

Aim the transmitter through the windscreen.

The Courtesy light does not

work

LED has failed Change LED.

The door reverses for no

apparent reason

This may occur occasionally from

environmental conditions such as areas that

are windy, dusty or have extreme temperature

changes.

If Safety beams are installed they may be

partially obstructed.

Ensure the door runs smoothly before increasing the force

pressure.

Ensure the beam path is not obstructed. Check the

Alignment.

Auto Close not working Safety Beam or wiring faulty Repair Safety Beam or replace wiring.

Re-align optics. See Safety Beam instructions.

The door stops or moves

very slowly under battery

(Optional Battery Back Up

Accessory)

The batteries may have little OR no charge Connect mains power and leave the batteries to charge. The

batteries may take 24 to 48 hours to reach their maximum

charge capacity.

The SERVICE LED has

started to flash and is

beeping numerous times

A Fault has been detected. The fault will

be active each time an attempt is made to

operate the door.

Record opener function (How many beeps?) then press the

SET button once to reset the opener. If the fault continues to

be tripped contact 13 62 63 for support.

The Open (Green) LED and

Close (Red) LED are flashing

alternatively

Opener is overloaded Check the doors operation by disengaging the motor and

ensuring the door runs smoothly. If necessary make door

adjustments or contact your door professional.

The Open (Green) LED

continues to flash

Door obstructed when opening Clear away any obstructions and test door opens correctly.

(If door is damaged, contact your door professionl).

The Close (Red) LED

continues to flash

Door obstructed when closing

Limits may be cleared

Clear away any obstructions and test door closes correctly.

(If door is damaged, contact your door professional).

Remove all power sources (including the battery backup).

Wait till all lights are out (10-15 secs), then reconnect power.

If Red LED is flashing, limits are not set. Reset Limits.

To Decrease Force Pressure

a. Hold down the FORCE MARGIN SET

button.

b. While holding the FORCE MARGIN SET

button, press the MINUS (-) button. Each

press will decrease the force margin.

c. The CLOSE LIMIT LED will flash each

time the MINUS (-) button is pressed to

indicate a decrease in force.

d. If the CLOSE LIMIT LED flashes

continuously when the MINUS (-) button

is being pressed, this indicates that the

minimum force setting has been reached.

e. Test the force again as per Testing Close

Cycle and Testing Open Cycle.

To Recalculate Force Margins

a. Press and hold the FORCE MARGIN

SET Button for six (6) seconds, the

beeper will sound once.

b. The door will start to move and re-

calculate force margins. The door can

move between the open and close

limit positions up to four (4) times

(depending on the position of the door

and the power up condition).

c. A single beep will be heard once the

process is complete.

d. Test the force again as per Testing Close

Cycle and Testing Open Cycle.

Safety Obstruction Forces Troubleshooting Guide

Tools Required

• Ladder

• Adjustable Wrench

• Socket set

• Drill

• Screwdrivers

• Marker Pen

• Door Stand

Important Note:

Only Tri-Tran

Technology Transmitters

and Keypads are compatible with this

SDO-2V2 product.

Summary of content (2 pages)

PAGE 1
Ensure ladder is the correct type for job. Ensure ladder is on flat firm ground that will take the weight without the legs sinking. Ensure user has 3 points of contact while on ladder. Place a 2 metre exclusion zone around area under the door while it is unsecured. Do not move under a door while it is on the door support (or ladder) Follow the installation instructions Fit door support (or ladder) snugly under door before removing bracket.
PAGE 2
Determine the Door Type Sectional door with track / B&D Flex-A-Door® a. 60mm b. Level Track Open the door and find the highest point of travel of the top door panel. Using a level, transfer this height to the wall above the door and mark a line 60mm above it. a. 60mm Door c. 5 d. e. Drilled holes f. 16 11 g. 6 b. Level Track WARNING! Make sure concrete, brick wall or timber lintels are solid and sound so as to form a secure mounting platform. 1.