IE-MediaChassis/2 (DC) Operation Manual
FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents FCC Radio Frequency Interference Statement ........................................................ ii Warranty................................................................................................................ ii About the IE-MediaChassis/2 (DC)..........................................................................1 Installing the IE-MediaChassis/2 (DC)......................................................................1 Configuring and Installing Modules................
About the IE-MediaChassis/2 (DC) The IE-MediaChassis/2 (DC) is a stand-alone chassis for use with iMcV modules. As an unmanaged chassis, the IE-MediaChassis/2 (DC) supports two single-wide or one dual-wide iMcV module. All iMcV modules, with the exception of the SNMP management card, will function properly in this chassis. The IE-MediaChassis/2 (DC) contains an internal Telco compatible DC power supply. The iMediaChassis/2 (DC) includes a temperature triggered fan.
The rack-mount shelf is sold separately. To purchase the rack-mount shelf (part number 895-39949); visit the IMC Networks’ Product Accessories page: https://www.imcnetworks.com/Products/acc.cfm Rackmounting requires a rackmount shelf for mounting up to three units side by side. 3. If mounting the chassis on a wall, place two #10 panhead screws (not supplied) on the wall the distance of the holes on the chassis, and then hang the unit on the screws. 4.
Configuring and Installing Modules IMC Networks recommends turning the chassis power off before proceeding. 1. To install an iMcV module, slide the module into the chassis until the module is firmly seated in the backplane. 2. Secure the module to the chassis by tightening the captive thumb screw on the iMcV module. 3. Attach the network cables between the iMcV module and other devices that will be interconnected. 4. Connect the DC power source.
1. This equipment shall be connected directly to the DC supply system earthed electrode conductor or to a bonding jumper from a grounded terminal bar or bus to which the DC supply system grounding electrode conductor is connected. 2. This equipment shall be located in the same immediate area (such as, adjacent cabinets) as any other equipment that has a connection between the earthed conductor of the same DC supply circuit and the earthing conductor, and also the point of earthing of the DC system.
DC Power Supply Precautions The following precautions must be observed when installing the chassis model with an internal DC power supply. 1. 2. Check nameplate ratings to ensure there is no overloading of supply circuits that could effect over current protection and supply wiring. In addition, the following must be observed: a. Connect the equipment to a 35 to 60 VDC power source that is electrically isolated from the alternating current source. b.
IMC Networks Technical Support Tel: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada); +32-16-550880 (Europe) Fax: (949) 465-3020 E-Mail: techsupport@imcnetworks.com Web: www.imcnetworks.com Specifications Environmental: Operating Temperature: -31° F to 156.2° F (-35° C to 69° C) Storage Temperature: -4° F to 158° F (-20° C to 70° C) Humidity: 5 to 95% (non-condensing) DC Power Supply: Input voltage: 35 to 60 VDC Input Current: 2.
Electrostatic Discharge Precautions Electrostatic discharge (ESD) can cause damage to your add-in modules. Always observe the following precautions when installing or handling an add-in module or any board assembly. 1. Do not remove unit from its protective packaging until you’re ready to install it. 2. Wear an ESD wrist grounding strap before handling any module or component.
Safety Certifications UL/CUL: Listed to Safety of Information Technology Equipment, including Electrical Business Equipment. CE: The products described herein comply with the Council Directive on Electromagnetic Compatibility (89/336/EEC) and the Council Directive on Electrical Equipment Designed for use within Certain Voltage Limits (73/23/EEC). Certified to Safety of Information Technology Equipment, Including Electrical Business Equipment. For further details, contact IMC Networks.
19772 Pauling • Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 • FAX: (949) 465-3020 www.imcnetworks.com © 2008 IMC Networks. All rights reserved. The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any errors that may appear in this document. IE-MediaChassis/2 is a trademark of IMC Networks. Other brands or product names may be trademarks and are the property of their respective companies.
