[鍵入文字] AW-NB101 IEEE 802.
[鍵入文字] I. Introduction i. Overview Azurewave AW-NB101 combo wireless slim module is a highly integrated wireless local area network (WLAN) solution to let users enjoy the digital content through the latest wireless technology without using extra cables and cords. It provides easy-to-use, high performance, cost effective and low power solution. Moreover, AW-NB101 enables compatible high-speed wireless connectivity within home, business and public access wireless networks. Compliant with the IEEE 802.
[鍵入文字] iii. Product Review When the USB wireless module is transmitting data through connection, LED indicator will blink. 1. Connection Mode ◎Infrastructure Mode Infrastructure mode needs an access point to establish the network, which can provide wireless accesses within valid range for users to communicate with others or transmit data with a wired network.
[鍵入文字] Infrastructure Mode ◎Ad-hoc Mode The difference between Ad-hoc mode and Infrastructure mode is that Ad-hoc mode does not need the access point or router. When you use this mode, your computer will act as a server within the valid range and connect directly to others in the same LAN workgroup. Ad-hoc Mode It is recommended to choose this mode when there is no access point showed on your wireless network.
[鍵入文字] II. Installation i. System Requirements Before you install AW-NB101, please make sure your system meets the following requirements. *Desktop or Laptop with USB 1.1/2.0 port *Minimum of 64MB system memory *Operating system: XP/Vista/Windows 7 *An optical drive/CD-ROM for utilities and driver installation ii. Hardware Installation 1. Find an available USB 1.1/2.0 port on your desktop or laptop. 2. Plug AW-NB101 Wireless PCI-E Module into USB port of desktop or laptop. iii.
[鍵入文字] iv. Setup: Windows XP OS If your computer is running a Windows operating system, it will automatically detect the AW-NB101 after the system boots up and displays a “Found New Hardware Wizard” window. Please click [Cancel] and proceed with the following steps. 1.
[鍵入文字] 2.
[鍵入文字] 3. Please select click [Install] to proceed 4.
[鍵入文字] 5.
[鍵入文字] 6. When it is completed, please click [Finish] 9.
[鍵入文字] v. Setup: Windows Vista OS Please follow the steps to complete installation. 1. Launch the setup driver 2.
[鍵入文字] 3. Now the Wizard is preparing installation 4.
[鍵入文字] 5.
[鍵入文字] 8.
[鍵入文字] 15
[鍵入文字] III. Network Connection i. For Windows XP OS Please see the following steps to setup network connection for Windows XP. 1. Find the network icon on the desktop shortcut and right-click on it. Choose “View Available Wireless networks” 2.
[鍵入文字] 3. Please wait for few seconds to let system connecting to selected wireless network 4. You may need to type the network key when it is required 5. Now the selected wireless network is connected 6.
[鍵入文字] 7. Here is the wireless network connection status ii. For Windows Vista OS Following are the instructions to setup wireless connection for Windows Vista. 1. Right-click on the network icon located on desktop shortcut.
[鍵入文字] 2. Choose wireless network within your range and click [Connect] * If selected network is not secure, please choose [Connect anyway] 3.
[鍵入文字] 4. Now the selected wireless network is connected 5.
[鍵入文字] [Status] 6.
[鍵入文字] 22
[鍵入文字] IV. Setup for Ad-hoc Mode i. For Windows XP OS If you want to choose Ad-hoc mode, please right-click network icon on desktop shortcut and choose “Open Network Connections”, or go to [Control Panel] and double-click “Network Connection” icon. When you see the “Network Connections” screen, please follow the steps below to setup Ad-hoc mode.
[鍵入文字] 1. Double-click “Wireless Network USB Adapter” icon to enter its properties 2.
[鍵入文字] 3. Choose “Use the following IP address:” and type the IP address; then click [OK] *Note: the IP address of the other wireless card should be set with the same subnet mask 4.
[鍵入文字] 5.
[鍵入文字] 6. Type “Network name (SSID)” and choose “Data encryption” if you want to protect the network security 7. When you see the dialogue showing your network is unsecured, please click [Continue Anyway] 8.
[鍵入文字] ii. For Windows Vista OS Please follow the steps to setup Ad-hoc mode for Windows Vista. 1.
[鍵入文字] 2. When you see the “Network and Sharing Center” windows, please select “Manage network connection” bar 3.
[鍵入文字] 4. When you see the warning message, please click [Continue] 5.
[鍵入文字] 6.
[鍵入文字] 7. Choose “Manage wireless networks” bar 8.
[鍵入文字] 9.
[鍵入文字] 10. Please click [Next] 11. Enter “Network name” and if you want to protect the network security, please choose in “security type”; then click [Next] 12.
[鍵入文字] Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
[鍵入文字] compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
[鍵入文字] This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
[鍵入文字] For Taiwan 警語： 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立 即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線 電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之 干擾。 Note: 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2.
[鍵入文字] Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
[鍵入文字] This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
[鍵入文字] Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
