Installation guide

Quadro Manual II: Administrator's Guide Administrator's Menus
Quadro4x, 4xi, 4xa, 4xia, 4xs, 4xis, Quadro16x, 16xi, 16xa, 16xia, 16xs, 16xis; (SW Version 3.1.x) 66
The second page of the Call Routing Wizard offers different
components depending on the Call Type selected on the
previous page.
Use Extension Settings is applicable to SIP and IP-PSTN call
types only and allows to select the extension (also Auto
Attendant) on behalf of the call that will be placed. The SIP
settings of the selected extension will be used as the caller
information. If no entry is selected in this list, the original caller
information will be kept. When Keep original DID checkbox is
selected, called destination will receive the original caller’s
information, rather than the information of extension selected
from the Use Extension Settings list.
Destination Host requires the IP address or the host name of
the destination (for a direct call) or the SIP server (for calls
through the SIP server).
Destination Port requires the port number of the destination or
of the SIP server.
User Name and Password require the identification settings for
the public SIP server or servers requiring authentication.
The Multiple Logons (ML) checkbox is available only for the IP-
PSTN call type and allows/denies multiple logon to the public
SIP server with the same username at the same time.
Fig. II-115: Call Routing Wizard - page 2
Use RTP Proxy checkbox is available for SIP and IP-PSTN call types and is applicable only when route is used for calls through Quadro between
peers both located outside the Quadro. When this checkbox is selected, RTP streams between external users will be routed through Quadro,
otherwise, when checkbox is not selected, RTP packets will be moving directly between peers.
A group of AAA Required checkboxes is used to choose one or more Authentication, Authorization, and Accounting (AAA) settings:
• Local Authentication – with this checkbox selected, callers will need to pass authentication through Local AAA table (see below) when
dialing the current pattern.
• RADIUS Authentication and Authorization – checkbox is present for all call types except PBX calls and when RADIUS client is enabled.
With this checkbox selected, when dialing the current pattern, callers will need to pass the authentication through RADIUS server (see
above).
• RADIUS Accounting - checkbox is present for all call types except PBX calls and when RADIUS client is enabled. With this checkbox
selected, no authentication will take place, but a caller identifying CDR (call detail report) will be sent to the RADIUS server. Checkbox
selection enables accounting on the RADIUS for the certain call.
If the authentication is configured based on the caller’s address, callers will pass the authentication automatically; otherwise they will be
required to identify themselves by a username and a password.
The Fail Reason drop down list indicates available failure reasons and contains different failure reasons, depending on the call type selection on the
previous page. Following Fail Reasons may be available in this list:
• Cannot Establish Connection - failure reason is available for FXO and ISDN calls only and indicates cases when connection cannot be
established.
• Wrong Number – available for PBX, SIP and IP-PSTN call types and indicates cases when the dialed number is wrong.
• Busy - available for PBX, SIP and IP-PSTN call types and indicates cases when the dialed destination is busy.
• Network Failure - available for SIP and IP-PSTN call types and indicates cases when system overload, network failure or timeout
expiration occurred.
• Other - available for SIP and IP-PSTN call types and indicates cases when authorization, negotiation, not supported or request rejected or
other unknown errors occur.
• System Failure - available for SIP and IP-PSTN call types and indicates cases indicated in Network Failure and Other fail reasons.
•
None – available for all call types and indicates no fail reason.
• Any - available for all call types and indicates any of above mentioned fail reason.
If the call cannot be established due to some of the selected Failure Reason, the call routing table will be parsed for the next matching pattern and, if
found, the call will be routed to the specified destination.
SIP Privacy manipulation radio buttons group is available for SIP call type only and allows to select the security of the SIP route by means of hiding
(or replacing, depending on the configuration of the SIP server) the key headers of the SIP messages used to establish the call.
• Default Privacy – with this selection, no Quadro specific SIP privacy will be applied, all privacy will be relied on the configuration of the
SIP Server.