User Manual

HOW TO CLEAN AND DISASSEMBLE THE REAR
INTERNALS
1. Pull the Top Cocking Knob (PBP3) up.
2. Pull the Bolt (PB03) out the back of the Pump Sled
(PA01)
3. Turn the End Cap (EC01) counterclockwise until it is
free of the marker’s body.
4. Remove the Pump Striker Spring (PSS2) from the
Marker.
5. Tilt the marker backwards and slide the Pump Striker
(PS02) out of the marker.
It may get caught on the trigger sear. If this happens,
pull the stiker out using a nger.
You may also push the stiker out from the top of the
marker with an allen key.
6. Use a squeegee or barrel swab to clean the inside of
the body.
Use a towel or rag to remove any paint or debris from
the Pump Bolt (PB03).
7. Apply a thin layer of Azodin lube to the Bolt Orings
(R015) and the Pump Striker (PS02).
HOW TO REASSEMBLE THE REAR INTERNALS
1. Insert the Pump Striker (PS02) into the lower tube of
the marker. Make sure the U-shapde cut is facing
upwards, towards the bolt. The striker will get stuck on
the trigger sear. In order to clear the sear, you will
need to push and hold the striker forward.
Then pull the trigger to disengage the sear.
2. The striker should now be clear of the sear. If it is
caught again, repeat the actions described in step one.
3. Insert Pump Bolt (PB03) into the Pump Sled (PB01)
4. Insert the Pump Bolt Pin (PBP3) into the hole, located
above the Pump Sled (PB01).
Be sure to push the Pump Bolt Pin (PBP3) all the way
down.
5. Insert the Pump Spring (PSS2) into the lower tube.
6. Insert the End Cap (EC01) into the back of the marker.
Check to see that the Velocity Adjuster (VA01) goes
through the Pump Striker Spring (PSS2).
7. Turn the End Cap clockwise until it is ush with the
body.
TROUBLESHOOTING
WARINIG: Remove all paintballs, loaders, and air tanks
before disassembling the marker.
TROUBLESHOOTING
WARINIG: Remove all paintballs, loaders, and air tanks
before disassembling the marker.
If you have questions or require further assistance, please
contact Azodin Paintball.
Email: [e-mail]
Phone: [phone]
Symptoms
Leaks down the barrel / body and
trigger frame
1. Tighten M8 x 8L Screw
2. Replace Zero Cup Seal (ZCS2)
3. Replace Orings RP15 and R015
4. Replace Valve (MFV2)
Leaks between Body and Vertical Adapter 1. Replace R015 Oring between Vertical
Adapter (VAS1) and Body (KP3B)
Leaks from middle of the regulator, small
hole above the set screw
1. Replace RV08 Oring
2. Replace RV14 Oring
3. Reset Regulator, refer to PG. 8
Leaks from the regulator, small hole on
the bottom near the swivel
1. Replace RV11 Oring
Leaks from ASA, small hole on the bottom
(nearest the tank)
1. Replace the Tank’s Oring
Leaks from ASA, small hole on the bottom
(nearest the screw knob (BAC2)
1. Replace the RV08 Oring that is held in
by the Retaining Screw (BARS)
Repair Step(s)
Symptoms
Leaks from Pump Guide (PG01) / Zero
Pump Cap (ZPC1)
1. Replace R010 Oring
2. Replace RV10 Oring
Loose ASA 1. Tighten M5 x 10L screw located inside
of the trigger framea
Striker is not catching the sear when pump
handle is pulled back
1. Striker may not be in the right
orientation. Rotate the striker 180
degrees.
2. Check to make sure the Bolt Pin (PBP3)
is pushed all the way down
Repair Step(s)