330 DUAL-CHANNEL CAMERA-MOUNT UHF WIRELESS MICROPHONE SYSTEM 330UPR - 35BT - 35HT - 35XT INSTRUCTION MANUAL
Thank you for purchasing the Azden 330 Dual-Channel Wireless Microphone system.
330UPR Dual-Channel Receiver After installing new batteries, mount the receiver to your video camera with supplied shoe mount or hook & loop fastener. Select one of the supplied cables and connect the output on the receiver and input on the video camera. Turn the power switch for Ch. 1 and/or Ch. 2 to “ON” and the battery level indicator on the LCD display should come on. If not, check the batteries. When the 330UPR receives a signal from the transmitter, the reception level indicator will come on.
330UPR Dual-Channel Receiver ①Antennas For the best reception, the antennas should be pointed in an upward position. Use caution and do not force them into this position. ②Power Switch for each Channel A separate Power Switch for Channel 1 and 2. ③Universal LCD Display for Ch. 1 and 2 The LCD Display shows multifunctional readout and can be switched between the channels by pressing the DISP 1/2 Button (5). Refer to “LCD Display Readouts” in this manual for further details.
⑤DISP 1/2 Button Press to switch the LCD Display between Ch. 1 and 2. ⑥LCD Display MODE Switching Button Press to switch the LCD Display to show the actual frequency number in MHz being used on each channel. ⑦PHONE Jack This jack allows you to monitor the sound. If a stereo headphone is used, Ch. 1 will be heard on the left and Ch. 2 on the right. ⑧MIC OUT Jack The 330UPR is supplied with both mini-to-mini and mini-to-dual XLR cables. For mini jack microphone inputs: Use the supplied mini-to-mini cable.
LCD Display Readouts BATT 1 2 LEVEL BATT 30-02 1 2 LEVEL 579.375 Displays the selected channel between Ch. 1 and Ch. 2. TV channel number (30 – 33) Transmit channel number (01 -47) Reception level indicator: 4 bars = High, 1 bar = Low Battery level indicator: 3 bars = High, 1 bar = Low The actual frequency number in MHz. Push the MODE button to see this display.
⑪Battery Compartment Lid Remove the battery compartment lid by sliding it down. ⑫Battery Compartment Install two fresh alkaline “AA” batteries. Make sure the battery polarity is correct as marked inside the battery compartment. Inside the battery compartment, you will also find: ⑬MIC Input Level Control This control enables you to adjust the input level of the microphone.
35XT Plug-in Transmitter ⑱Battery Compartment Open the battery compartment lid by pushing down on the tab and lifting it up. Install two fresh alkaline “AA” batteries. Make sure the battery polarity is correct as marked inside the battery compartment. ⑲POWER Switch Turns the 35XT Transmitter “ON” or “OFF”. ⑳AUDIO Switch It is best to set the AUDIO switch to “OFF” prior to first turning the POWER switch “ON”. When you are ready to begin transmitting, turn the AUDIO “ON”.
㉑MIC Connector/Locking Ring This 3-pin XLR connector is the microphone input. Any low impedance microphone with a corresponding connector may be plugged here. Once the microphone is plugged into the 35XT, the locking ring should be rotated clockwise until snug. To remove the microphone, first rotate the locking ring counterclockwise and then pull the microphone away while pressing the XLR release. ㉒MIC Input LEVEL Control This enables you to adjust the input level of the connected microphone.
35HT Handheld Microphone/Transmitter ㉔Battery Compartment Cover Remove the battery compartment cover by rotating it counterclockwise and sliding it down. ㉕Battery Compartment Install two fresh alkaline “AA” batteries. Make sure the battery polarity is correct as marked inside the battery compartment. ㉖MIC LEVEL Control This enables you to adjust the audio level of the microphone. Using the supplied tool, turn the orange dial clockwise to increase, or counterclockwise to decrease the audio level.
㉗Channel UP and DOWN Button To change the channel number, use the tip of the tool provided and press the UP or DOWN button until the desired channel number is shown on the LCD Display. Keep the button pressed to fast forward the channel numbers. ㉘POWER Switch Turns the 35HT Transmitter/Microphone “ON” or “OFF”. ㉙LCD Display The LCD display shows the following information: TV Ch – Transmit Channel Number (i.e. 30 – 01, 31 – 12, 33 – 47) The TV – Transmit channel display is made of two parts.
Specifications 330UPR Receiver Frequency Range: Type of Reception: Oscillator: RF Squelch Level: Frequency Response: S/N Ratio: Audio Out: Batteries: External Power: Dimensions: Weight: 35BT Body-Pack Transmitter Frequency Range: Oscillator: RF Power: Frequency Response: Max Deviation: Batteries: Dimensions: Weight: 35XT Plug-in Transmitter Frequency Range: Antenna: Max Input Level: RF Power: Input Impedance: Audio Adjust Range: Batteries: Dimensions: Weight: UHF 188 Selectable Frequencies (566.
