User Manual

ManualsBrandsAXXESS ManualsCar Electronics & GPSAXXESS - Wiring Harness for Select Chrysler, Dodge and Fiat Vehicles - Black

Installation instructions for part LC-CHRC-01

REV. 8/16/2016 INSTLC-CHRC-01

axxessinterfaces.com

•

metraonline.com

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Used in non-amplified models, or when bypassing a factory amplifier

• Fiat 500L only: For use in both amplified and non-amplified systems

• Provides NAV outputs (parking brake, reverse, and speed sense)

• Pre-wired ASWC-1 harness (ASWC-1 sold separately)

• Retains the factory backup camera (if displayed through the OE radio)

• Retains the 3.5mm AUX-IN jack

• Retains balance and fade

• Retains safety chimes

• Micro “B” USB updatable

INTERFACE FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

LC-CHRC-01

Chrysler Data Interface 2013-up

APPLICATIONS

• LC-CHRC-01 interface • LC-CHRC-01 harness

INTERFACE COMPONENTS

Connections to be made ................................................... 2

Installing the LC-CHRC-01................................................ 3

Initializing the LC-CHRC-01 .............................................. 3

TABLE OF CONTENTS

CHRYSLER

200 LX 2015-up

DODGE

Dart (small screen option)

2013-up

FIAT

500L 2014-up

500X 2016-up

JEEP

Cherokee Sport 2014-up

Renegade 2015-up

RAM

1500/2500/3500 (small screen

option) 2013-up

Chassis Cab 3500/4500/5500

(small screen option) 2013-up

Promaster 2014-up

Promaster City 2015-up

Summary of content (8 pages)

PAGE 1
Installation instructions for part LC-CHRC-01 REV. 8/16/2016 INSTLC-CHRC-01 LC-CHRC-01 Chrysler Data Interface 2013-up • • • • • • • • • • • INTERFACE FEATURES Provides accessory power (12-volt 10-amp) Retains R.A.P.
PAGE 2
LC-CHRC-01 Connections to be made From the LC-CHRC-01 harness to the aftermarket radio: The following (3) wires are only for multimedia/navigation radios that require these wires. • Connect the Black wire to the ground wire. • Connect the Blue/Pink wire to the VSS/speed sense wire. • Connect the Yellow wire to the battery wire. • Connect the Green/Purple wire to the reverse wire. • Connect the Red wire to the accessory wire. • Connect the Light Green wire to the parking brake wire.
PAGE 3
LC-CHRC-01 Installing the LC-CHRC-01 Initializing the LC-CHRC-01 Attention! If the interface loses power for any reason, the following steps will need to be performed again. Also, if installing an ASWC-1 connect it after you initialize and test the interface/radio, with the key in the off position. With the key in the off position: • Connect the LC-CHRC-01 harness into the interface, and then to the harness in the vehicle.
PAGE 4
Installation instructions for part LC-CHRC-01 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. REV.
PAGE 5
Instrucciones de instalación para la pieza LC-CHRC-01 REV. 8/16/2016 INSTLC-CHRC-01 LC-CHRC-01 Chrysler Interfase de Datos 2013 y mas • • • • • • • • • • • CARACTERÍSTICAS DE LA INTERFASE Provee corriente de accesorios (12 voltios 10 amperes) Retiene R.A.P.
PAGE 6
LC-CHRC-01 Conexiones que se deben hacer Desde el arnés LC-CHRC-01 al radio de mercado secundario: Los siguientes (3) cables son para radios de mercado secundario con multimedios/ navegación que tienen estos cables. • Conecte el cable negro al cable de tierra. • Conecte el cable azul/rosa al cable VSS o de detección de velocidad. • Conecte el cable amarillo al cable de la batería. • Conecte el cable verde/púrpura al cable de reversa. • Conecte el cable rojo con el cable de accesorios.
PAGE 7
LC-CHRC-01 Instalación del LC-CHRC-01 Inicialización del LC-CHRC-01 Con la llave en la posición de apagado: Atención! Si la interfase pierde energía por cualquier razón, tendrán que volverse a ejecutar los siguientes pasos. Si va a utilizar el ASWC-1, conéctelo después de inicializar y probar el interfase/radio con la llave en la posición de apagado. • Conecte el arnés LC-CHRC-01 a la interfase, y luego al arnés en el vehículo.
PAGE 8
Instrucciones de instalación para la pieza LC-CHRC-01 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar. REV.