User Manual

ManualsBrandsAXXESS ManualsCar Electronics & GPSWiring Harness for Select BMW and Mini Vehicles - Black

Installation instructions for part LC-BMRC-01

REV. 5/13/2016 INSTLC-BMRC-01

axxessinterfaces.com

•

metraonline.com

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Provides NAV outputs (parking brake, reverse, and V.S.S)

• Retains warning chimes

• For non-amplified models, or when bypassing a factory amplifier

• Retains balance and fade

• Micro “B” USB updatable

FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

LC-BMRC-01

BMW / Mini Chime Retention

2006-2015

APPLICATIONS

• LC-BMRC-01 interface • LC-BMRC-01 harness

• Fuse holder with 96” length of wire

INTERFACE COMPONENTS

BMW

1 Series (without amp) 2008-2013

3 Series (without amp) 2006-2013

M3 (without amp) 2007-2013

MINI

Cooper (without amp) 2007-2015

Connections to be made ................................................... 2

Installing the LC-BMRC-01 ............................................... 3

Initializing the LC-BMRC-01 ............................................. 3

TABLE OF CONTENTS

Summary of content (8 pages)

PAGE 1
Installation instructions for part LC-BMRC-01 LC-BMRC-01 BMW / Mini Chime Retention 2006-2015 REV. 5/13/2016 INSTLC-BMRC-01 • • • • • • • FEATURES Provides accessory power (12-volt 10-amp) Retains R.A.P. (retained accessory power) Provides NAV outputs (parking brake, reverse, and V.S.S) Retains warning chimes For non-amplified models, or when bypassing a factory amplifier Retains balance and fade Micro “B” USB updatable TABLE OF CONTENTS Connections to be made...........................................
PAGE 2
LC-BMRC-01 Connections to be made From the LC-BMRC-01 harness to the aftermarket radio: The following (3) wires are only for multimedia/navigation radios that require these wires. • Connect the Black wire to the ground wire. • Connect the Blue/Pink wire to the VSS/speed sense wire. • Connect the Yellow wire to the fuse holder with 96” length of wire: • Connect the Green/Purple wire to the reverse wire. • Remove the fuse from the fuse holder. • Connect the Light Green wire to the parking brake wire.
PAGE 3
LC-BMRC-01 Installing the LC-BMRC-01 Initializing the LC-BMRC-01 With the key in the off position: Attention! If the interface loses power for any reason, the following steps will need to be performed again. Also, if installing an ASWC-1 connect it after you initialize and test the interface/radio, with the key in the off position. • Connect the LC-BMRC-01 harness into the interface, and then to the vehicle. • Re-insert the fuse back into the fuse holder.
PAGE 4
Installation instructions for part LC-BMRC-01 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. REV.
PAGE 5
Instrucciones de instalación para la pieza LC-BMRC-01 LC-BMRC-01 BMW / Mini Retención de Timbre 2006-2015 REV. 5/13/2016 INSTLC-BMRC-01 • • • • • • • CARACTERÍSTICAS Provee corriente de accesorios (12 voltios 10 amperes) Retiene R.A.P.
PAGE 6
LC-BMRC-01 Conexiones que se deben hacer From the LC-BMRC-01 harness to the aftermarket radio: Los siguientes (3) cables son para radios de mercado secundario con multimedios/ navegación que tienen estos cables. • Conecte el cable negro al cable de tierra. • Conecte el cable azul/rosa al cable VSS/detección de velocidad. • Conecte el cable amarillo con portafusibles con 96” longitud del cable: • Conecte el cable verde/púrpura al cable de reversa. • Retire el fusible del portafusibles.
PAGE 7
LC-BMRC-01 Instalación del LC-BMRC-01 Inicialización del LC-BMRC-01 Con la llave en la posición de apagado: Attention! Si el interfase pierde la alimentación por cualquier motivo, deberá realizar el siguiente paso de nuevo. Además, si la instalación de un ASWC-1 conectarlo después de inicializar y probar la interfaz / radio, con la llave en la posición de apagado. • Conecte el arnés LC-BMRC-01 a la interfase, y después al vehículo. • Vuelva a insertar el fusible nuevo en el portafusibles.
PAGE 8
Instrucciones de instalación para la pieza LC-BMRC-01 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar. REV.