User Manual

AX-MTR
®
7
Programming the AX-MTR with a Feature Number
Please READ! Many technical phone calls can be avoided by reading this
section thoroughly.
• In the instructions below, when asked to ‘Pulse’ the trigger wire, this will
indicate to temporarily ground the BROWN wire to chassis ground and then
ungrounding it. Each time you do this, the LED indicator will turn on and off.
•
All ‘Feature Select’ and ‘Timer’ section in the chart MUST be programmed from a
left to right order. Even if you do not need all the outputs of the AX-MTR, an option
or time must be set for that wire(s) in order for the AX-MTR to finish programming
.
• If you do not understand this written part of the instructions, you can use the
flow chart on page 4. The flow chart will help you program the AX-MTR step by
1.
Select a feature you want from the chart and write down the Feature above.
Slide the switch to the on position and apply 12-volt to the AX-MTR
RED wire.
‘Pulse’ the trigger wire the number of times of the selected Feature number. Wait
3 seconds, and the LED will flash the amount of times you ‘Pulsed’ the trigger
wire saving that Feature number into memory. note: If you are doing Feature# 1
through 4, 8 or 16, you may go directly to step #4 after you do step #1.
2. When selecting a feature, ‘Pulse’ the trigger wire once to select the 1st option,
twice within 3 seconds to select the 2nd option, or 3 times within 3 seconds to
select the third option.
Example: Feature# 9, 10, and 12 needs an option selected
.
- OR - If you need to select how many pulses you need to trigger an event, ‘Pulse’
the wire the number of times needed.
Example: Feature# 7, 11, 13, 14, and 15 need a number of pulses to trigger
an event.
After 3 seconds, the LED will flash the amount of times you ‘Pulsed’ the trigger
wire telling what option you selected or how many pulses the AX-MTR needs for
a triggered event. Repeat if other wires need to have an option selected. After all
remaining options are programmed in the ‘Feature Select’ section, the AX-MTR
will automatically go to the ‘Timer’ section.
3. In the ‘Timer’ section in the chart, where a ‘T’ is indicated, you will need to
program a time for that specific wire(s). If in the ‘Feature Select’ section you
programmed for a pulse or latched event for that color wire, then the timer for
that wire will be automatically skipped because the timer is not needed.
To start programming the time needed, ‘Pulse’ the trigger wire one time to
start the timer:
Minutes: The LED will flash rapidly 1 time, indicating you need to program the
number of minutes. ‘Pulse’ the trigger wire for the number of minutes needed.
After 3 seconds the LED will flash the number of minutes recorded. If you
program for 5 or greater, the AX-MTR will default to 4 for minutes. If you need
zero minutes, do nothing and wait the 3 seconds.
Seconds in tens place: The LED will flash rapidly 2 times indicating you need
to program the number of seconds in the tens place. ‘Pulse’ the trigger wire the
number of seconds needed. After 3 seconds the LED will flash the number of
seconds recorded in the tens place. If you program for 6 or greater, the AX-MTR
will default to 5 for the tens place. If you need zero seconds in the tens place,
do nothing and wait the 3 seconds.
Seconds in ones place: The LED will flash rapidly 3 times indicating you need
to program the number of seconds in the ones place. ‘Pulse’ the trigger wire
the number of seconds needed. After 3 seconds the LED will flash the number
of seconds recorded in the ones place. If you program for 10 or greater, the
AX-MTR will default to 9 seconds for the ones place. If you need zero seconds
in the ones place, do nothing and wait the 3 seconds.
Continued on the next page