User Manual

ManualsBrandsAXXESS ManualsCar Electronics & GPSAXXESS - Universal Trigger Output Module

Installation instructions for part AX-MTR

REV. 12/22/2016 INSTAX-MTR

axxessinterfaces.com

•

metraonline.com

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

The AX-MTR is a universal trigger output module that has various user programmable features

combined into one unit. The user programmable features are stored in non-volatile memory.

When triggered, the AX-MTR can turn on the outputs as a pulsed, latched or timed.

KIT FEATURES

AX-MTR

Features .........................................................................2-4

- Feature Chart ................................................................ 4

Wiring Instructions ........................................................5-6

Programming the AX-MTR ............................................7-8

TABLE OF CONTENTS

Black (-) Chassis ground

Red (+) 12-volt constant/switched

Green (+) 0.8 -16 volt input trigger

Brown (-) Input trigger

Blue (+) 12-volt output -2-amps max

White (-) Output -150 ma. max

Orange (-) Output - 150 ma. max

OFF-ON

Programming switch must be turned off after the AX-MTR is programmed!

AX-MTR

Summary of content (8 pages)

PAGE 1
® Installation instructions for part AX-MTR REV. 12/22/2016 INSTAX-MTR AX-MTR TABLE OF CONTENTS Features..........................................................................2-4 - Feature Chart................................................................. 4 Wiring Instructions.........................................................5-6 Programming the AX-MTR.............................................7-8 Black (-) Chassis ground Red (+) 12-volt constant/switched Green (+) 0.
PAGE 2
® AX-MTR Features #3 - Latch and unlatch output from a pulsed input: Turn on headlights, neon lights or radio from an alarm with a momentary output or from a momentary switch. Basic Description of Features: There are two inputs, the GREEN wire is a positive input that senses voltages as low as 0.8-volt and the BROWN wire is a negative input, both are tied together internally which is, essentially, ONE trigger input.
PAGE 3
® AX-MTR Features #8 - Linear Actuator Controller: Open/close amplifier racks from a momentary source like from a alarm’s negative output. Sequence is: Start, Stop, Reverse, and Stop. (Continued) #14 - Pulses to pulse output: Upon number of pulses within a user programmable time, the outputs will pulse. Example: if you programmed to see 4 pulses, for every 4 pulses the AX-MTR sees within a 5 second time period, the outputs will pulse once.
PAGE 4
® AX-MTR Features Feature Feature# Blue Low voltage trigger Alpine video bypass (factory default) Latching on / off outputs Double pulse Closed loop trigger Pulse extender Horn honk Linear actuator controller Doorlock pulse generator Channel splitter Number of pulses for constant output 3 programmable timer outputs on constant trigger Number of pulses to latch / unlatch output Number of pulses to pulse output Number of pulses for timer output Latching outputs #2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
PAGE 5
® AX-MTR Wiring Instructions 1. Connect the BLACK wire to chassis ground. ahead and an accident could occur. Install the AX-MTR only in RV and Marine applications where there is no parking/hand brake to interface to. Do not install the AX-MTR where the driver may be able to view the monitor when driving. 2. Connect the RED wire to switched 12-volt.
PAGE 6
® AX-MTR Wiring Instructions Connect the BROWN or GREEN wire to a momentary source. When pulsed the first time the WHITE wire will latch on, then 1.5 seconds later the BLUE wire will latch on (this will allow time for the limit switches to turn off) . On a second pulse both the BLUE and WHITE wire will turn off. On a 3rd pulse the ORANGE wire will latch on, then 1 second later the BLUE wire will latch on. #9: Connect the GREEN wire to a true ignition wire of the vehicle.
PAGE 7
® AX-MTR Programming the AX-MTR with a Feature Number Please READ! Many technical phone calls can be avoided by reading this section thoroughly. • In the instructions below, when asked to ‘Pulse’ the trigger wire, this will indicate to temporarily ground the BROWN wire to chassis ground and then ungrounding it. Each time you do this, the LED indicator will turn on and off. • All ‘Feature Select’ and ‘Timer’ section in the chart MUST be programmed from a left to right order.
PAGE 8
® Installation instructions for part AX-MTR REV. 12/22/2016 INSTAX-MTR Programming the AX-MTR with a Feature Number (Continued) End of timer: The LED will flash rapidly 4 times indicating that the timer is finish recording. Note: Repeat step 3 if more than one timer has to be recorded, otherwise go to step 4. Example 1: If you want 36 seconds for a timer, ‘Pulse’ the trigger wire one time. The LED will flash rapidly 1 time, wait 3 seconds and 0 minutes will be recorded.