Installation Guide

ManualsBrandsAXXESS ManualsCar Electronics & GPSData Interface Adapter for Select Hyundai and Kia Vehicles - Multi

AX-HYKIA3-SWC

INSTALLATION INSTRUCTIONS

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

INTERFACE FEATURES

INTERFACE COMPONENTS

OPTIONAL ACCESSORIES

(sold separately)

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun,

solder, and heat shrink • Tape • Wire cutter

• Zip ties • Small ﬂat-blade screwdriver

TABLE OF CONTENTS

Connections .........................................................2-3

Installation .............................................................4

Programming .........................................................4

Audio Level Adjustment ........................................4

Steering Wheel Control Settings

- L.E.D. feedback ....................................................5

- Changing radio type ...........................................5

- Remapping the steering wheel control buttons 5-6

- Dual assignment instructions (long button press) .7-8

Troubleshooting .....................................................8

Hyundai/Kia Data Interface with SWC 2017-up

• Provides accessory power

(12-volt 10-amp)

• Provides NAV outputs (park

brake, reverse, speed sense)

• Retains audio controls on the

steering wheel

• Designed for ampliﬁed‡ and

non-ampliﬁed models

• Retains the factory AUX-IN jack

• Retains the factory backup

camera

• Includes an AX-CAM6V 12-to-

6V step-down for the factory

camera

• Retains balance and fade†

• Micro-B USB updatable

• AX-HYKIA3-SWC interface • AX-HYKIA3-SWC harness

• AX-CAM6V • 16-pin harness with stripped leads

• Female 3.5mm connector with stripped leads

SPDIF Interface: AX-HYKIA-SPDIF interface

Visit AxxessInterfaces.com for more detailed information about the product and up-to-date

vehicle speciﬁc applications

‡ Requires the AX-HYKIA-SPDIF (sold separately)

† Non-ampliﬁed models only

APPLICATIONS

See inside front cover

Summary of content (8 pages)

PAGE 1
AX-HYKIA3-SWC I N S TA L L AT I O N I N S T R U C T I O N S Hyundai/Kia Data Interface with SWC 2017-up Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle specific applications INTERFACE COMPONENTS • AX-HYKIA3-SWC interface • AX-HYKIA3-SWC harness • AX-CAM6V • 16-pin harness with stripped leads • Female 3.
PAGE 2
APPLICATIONS Hyundai Accent (1) Elantra (2) Elantra (4) Elantra GT Ioniq (3) Kona Santa Fe Santa Fe XL Sonata Sonata (3) (1) (2) (3) (4) (5) 2018-up 2019-up 2017-2018 2018-up 2018-up 2018-up 2019-up 2019-up 2018-up 2017 Kia Forte Forte / Forte 5 (4) Optima (5) Rio / Rio 5 (1) Sedona (4) Sorento Soul (4) With Android Auto / Apple CarPlay radio With Android Auto / Apple CarPlay radio or NAV Without NAV With Android Auto / Apple CarPlay radio, without NAV With manual climate control 2019-up 2017-2018 2019
PAGE 3
CONNECTIONS The following (1) wire is only for a multimedia/navigation radio that requires this wire. • Connect the Blue/Pink wire to the VSS/speed sense wire. • If the factory AUX-IN jack is desired to be retained, connect the Red & White RCA jacks to the audio AUX-IN jacks. • Connect the Yellow RCA jack to the backup camera input. For models equipped without a factory amplifier: • Connect the Green wire to the left rear positive speaker output.
PAGE 4
INSTALLATION With the key in the off position: 1. Connect the 16-pin harness with stripped leads, and the AX-HYKIA3-SWC harness, to the AXHYKIA3-SWC interface. Attention! Do not connect the AX-HYKIA3-SWC harness to the wiring harness in the vehicle just yet. Attention! If retaining steering wheel controls, ensure that the jack/wire is connected to the radio before proceeding. If this step is skipped, the AX-HYKIA3-SWC interface will need to be reset for the steering wheel controls to function.
PAGE 5
STEERING WHEEL CONTROL SETTINGS L.E.D. feedback The (18) Red L.E.D. flashes represent the radio the AX-HYKIA3-SWC interface believes it’s connected to. Each flash represents a different radio Manufacturer. For example, if you are installing a JVC radio, the AX-HYKIA3-SWC interface will flash Red (5) times, and then stop. Following is a legend that dictates which radio Manufacturer corresponds to which flash. L.E.D.
PAGE 6
STEERING WHEEL CONTROL SETTINGS Radio legend (CONT.) Remapping the steering wheel control buttons Radio # Radio Radio # Radio 1 2 3 4 5 6 7 8 9 Eclipse (type 1) Kenwood Clarion (type 1) Sony / Dual JVC Pioneer / Jensen Alpine Visteon Valor 10 11 12 13 14 15 16 17 18 Clarion (type 2) Metra OE Eclipse (type 2) LG Parrot XITE Philips TBA JBL Once the AX-HYKIA3-SWC interface has been programmed, the button assignment for the steering wheel controls may be reassigned if so desired.
PAGE 7
STEERING WHEEL CONTROL SETTINGS Button function legend (CONT.) Dual assignment instructions (long button press) Function # Function Function # Function 1 2 3 4 5 6 7 8 9 Volume-Up Volume-Down Seek-Up/Next Seek-Down/Prev Source/Mode Mute Preset-Up Preset-Down Power 10 11 12 13 14 15 16 17 18 Band Play/Enter PTT (Push to Talk) On-Hook Off-Hook Fan-Up* Fan-Down* Temp-Up* Temp-Down* * Not applicable in this application Note: Some radios may not have these commands.
PAGE 8
AX-HYKIA3-SWC I N S TA L L AT I O N I N S T R U C T I O N S STEERING WHEEL CONTROL SETTINGS (CONT.