User Manual

ManualsBrandsAXXESS ManualsCar Electronics & GPSAXXESS - Car Audio Replacement Interface for Most Vehicles - Black

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-HYKIA1-SWC

INSTALLATION INSTRUCTIONS

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections to be made ....................................2-3

Installing the AX-HYKIA1-SWC ..............................3

Programming the AX-HYKIA1-SWC ......................4

Steering wheel control settings ....................... 4-7

- L.E.D. feedback ...................................................4

- Changing radio type ..........................................5

Remapping the steering wheel control buttons

. . 5-6

Dual assignment instructions (long button press)

. . 6-7

Troubleshooting .....................................................7

Hyundai/Kia Data Interface with SWC 2010-up*

APPLICATIONS

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains BlueLink

• Designed for ampliﬁed* and non-ampliﬁed models

• Retains balance and fade

• Micro “B” USB updatable

HYUNDAI

Elantra 2011-2016

Genesis Coupe * 2013-2016

Santa Fe * 2013-2016

Santa Fe Sport * 2013-2016

Sonata * 2011-2016

Sonata Hybrid * 2011-2015

Tucson 2010-2015

KIA

Optima 2011-2015

Sorento * 2014-2016

Sorento (with UVO) * 2012-2013

Sportage 2011-2016

• AX-HYKIA1-SWC interface

• AX-HYKIA1-SWC harness

• 16-pin harness with stripped leads

• Female 3.5mm connector with stripped leads

* Requires the AX-HYKIA-SPDIF (sold separately)

* Without NAV

*Visit AxxessInterfaces.com for up-to-date vehicle speciﬁc applications.

Summary of content (8 pages)

PAGE 1
AX-HYKIA1-SWC I N S TA L L AT I O N I N S T R U C T I O N S Hyundai/Kia Data Interface with SWC 2010-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
PAGE 2
CONNECTIONS TO BE MADE From the 16-pin harness with stripped leads to the aftermarket radio: • Connect the Red wire to the accessory wire. • If the vehicle comes equipped with a factory amplifier, connect the Blue/White wire to the amp turn-on wire. • If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute wire is not connected, the radio will turn off when BlueLink is activated. • Connect the Gray wire to the right front positive speaker output.
PAGE 3
CONNECTIONS TO BE MADE INSTALLING THE AX-HYKIA1-SWC 3.5mm jack steering wheel control retention: • The 3.5mm jack is to be used to retain audio controls on the steering wheel control. • For the radios listed below, connect the female 3.5mm connector with stripped leads, to the male 3.5mm SWC jack from the AX-HYKIA1-SWC harness. Any remaining wires tape off and disregard: • Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White wire of the connector.
PAGE 4
PROGRAMMING THE AX-HYKIA1-SWC For the steps below, the L.E.D. located inside the interface can only be seen while active. The interface does not need to be opened to see the L.E.D. • Start the vehicle. • Connect the AX-HYKIA1-SWC harness to the wiring harness in the vehicle. • The L.E.D. will initially turn on solid Green, then turn off for a few seconds while it auto detects the radio installed. • The L.E.D.
PAGE 5
STEERING WHEEL CONTROL SETTINGS Attention: The Axxess Updater App can also be used to program the following (3) sub-sections as well, pending that the interface has been initialized and programmed. Changing radio type If the LED flashes do not match the radio you have connected, you must manually program the AX-HYKIA1-SWC to tell it what radio it is connected to. 1. After (3) seconds of turning the key on, press and hold the Volume-Down button on the steering wheel until the L.E.D.
PAGE 6
STEERING WHEEL CONTROL SETTINGS Note: If the next function on the list is not on the steering wheel, press the Volume-Up button for (1) second until the L.E.D. comes on, and then release the Volume-Up button. This will tell the AX-HYKIA1-SWC that this function is not available and it will move on to the next function. 5. To complete the remapping process, press and hold the Volume-Up button on the steering wheel until the L.E.D. in the AX-HYKIA1-SWC goes out. Button assignment legend 1. Volume-Up 2.
PAGE 7
STEERING WHEEL CONTROL SETTINGS (CONT.) Dual assignment legend TROUBLESHOOTING Resetting the AX-HYKIA1-SWC 6. ATT/Mute 7. Preset-Up 11. Play/Enter 15. Fan-Up * 2. Not allowed 12. PTT 16. Fan-Down * 1. The Blue reset button is located inside the interface, between the two connectors. The button is accessible outside the interface, no need to open the interface. 3. Seek-Up/Next 8. Preset-Down 13. On-Hook 17. Temp-Up * 2.
PAGE 8
AX-HYKIA1-SWC I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.