User Manual

ManualsBrandsAXXESS ManualsCar Electronics & GPSAXXESS - Car Audio Replacement Interface for Select Fiat Vehicles - Black

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-FT901

INSTALLATION INSTRUCTIONS

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections to be made ....................................2-3

Installing the AX-FT901 interface ..........................3

Programming the ASWC-1 interface ................. 3-4

Screen operation ................................................4-6

Fiat 500 2015 / 500L 2014 (with U-Connect) Data Interface with SWC & Factory Display Retention †

• Provides accessory power

• Designed for non-ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains balance and fade

• Retains most of the vehicle settings that was displayed on the

factory radio *

• Micro “B” USB updatable

† For Continental Mopar head unit

* Attention!

The aftermarket radios backup camera input will be used to display the vehicle settings. If the radio doesn’t have a backup camera

Input, then there will be no visualization of the vehicle settings. An externally mounted screen could be substituted in this situation.

• AX-FT901 interface

• ASWC-1 interface

• AX-FT901 harness

• ASWC-1 harness

Summary of content (8 pages)

PAGE 1
AX-FT901 I N S TA L L AT I O N I N S T R U C T I O N S Fiat 500 2015 / 500L 2014 (with U-Connect) Data Interface with SWC & Factory Display Retention † † For Continental Mopar head unit INTERFACE FEATURES • Provides accessory power • Designed for non-amplified models • Provides NAV outputs (parking brake, reverse, speed sense) • Retains audio controls on the steering wheel • Retains balance and fade • Retains most of the vehicle settings that was displayed on the factory radio * • Micro “B” USB updatabl
PAGE 2
CONNECTIONS TO BE MADE From the aftermarket radio to the AX-FT901 harness: From the aftermarket radio to the ASWC-1 harness: • Connect the Black wire to the ground wire. This harness is only to be used if the vehicle is equipped with steering wheel controls or a backup camera. • Connect the Yellow wire to the battery wire. • Connect the Red wire to the accessory wire. • Connect the Red wire to the accessory wire. • For the radios listed below, connect the female 3.
PAGE 3
CONNECTIONS TO BE MADE (CONT.) • For all other radios: Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the aftermarket radio designated for an external steering wheel control interface. Please refer to the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to. • Connect the Yellow male RCA jack labeled “To Reverse Camera Input (Radio)”, to the backup camera input. Note: The aftermarket radios backup camera input will be used to display the vehicle settings.
PAGE 4
PROGRAMMING THE ASWC-1 INTERFACE (CONT.) SCREEN OPERATION L.E.D. feedback Configuration Menu Vehicle Settings Interface Settings Language Version < Back The (18) Red L.E.D. flashes represent what brand radio the ASWC-1 believes it is connected to. Each flash represents a different radio manufacturer. For example, if you are installing a JVC radio, the ASWC-1 will flash (5) times. Following is a legend that dictates which manufacturer corresponds to which flash. L.E.D.
PAGE 5
SCREEN OPERATION Vehicle Settings Display Clock Doors and Locks Lights Safety and Driving Assistance < Back Vehicle Settings • This is the main settings screen to access the factory settings. All button functions are retained and controlled in the same manner that the factory buttons were controlled. Refer to the vehicle owner’s manual for more information. (CONT.
PAGE 6
SCREEN OPERATION Picture Settings Brightness Contrast Saturation < Back Picture Settings • Adjust brightness, contrast, and color saturation. (CONT.) Preferences Park Assist Version 0 Camera Connected Yes Reverse Priority Park Assist Park Brake Source Speed Restore factory settings < Back Preferences • Park Assist Version - Select according to the color configuration of the park assist fitted to the vehicle. • Camera Connected - Select ‘Yes” if an optional backup camera will be installed.
PAGE 7
REV.
PAGE 8
AX-FT901 I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.