ASBT504 INSTALLATION / OWNER'S MANUAL Wireless Smart EQ Processor
INSTALLATION Preparation 0LEASE READ ENTIRE MANUAL BEFORE INSTALLATION $UE TO THE TECHNICAL NATURE OF THIS PRODUCT THAT HAS TO CONNECT TO THE AMPLIFIER IT IS HIGHLY RECOMMENDED THAT YOUR 3MART %1 IS INSTALLED BY A PROFESSIONAL INSTALLER OR AN AUTHORIZED DEALER Before You Start s $ISCONNECT NEGATIVE BATTERY TERMINAL CONSULT A QUALIFIED TECHNICIAN FOR INSTRUCTIONS s !VOID INSTALLING THE 3MART %1 WHERE IT WOULD BE SUBJECT TO HIGH TEMPERATURES SUCH AS DIRECT SUNLIGHT OR WHERE IT WOULD BE SUBJECT TO DUST DIR
INSTALLATION Connection Descriptions Power Wire (+12V) s Disconnect negative battery terminal before processing. Consult a qualified technician for instructions if you are unsure. s Plan wire routing before cutting any wires to length. Begin by routing the power +12V wire from the battery to the Smart EQ location. Power line for amplifier can be shared. Use a grommet when running wires through the firewall or metal openings.
INSTALLATION Inputs/Output Panel Description [ Input Side ] 2 1 3 4 5 1 Line Input 3 Power LED 2 High Level Input 4 Power Connector 5 Reset [ output side ] 1 4 2 4 3 1 Remote-out for Amplifier Turn on/off 3 Line Output Rear 2 Line Output Front 4 Line Output Subwoofer
INSTALLATION Typical Wire Routing ACC MAXIMUM FUSE 12V BATTERY +12V DC (Power) GROUND No more than 36" (1 meter) ACC [Subwoofer] [HEAD UNIT] [Mono Amplifier] [Front Speakers] RCA Low level Input [Smart EQ] [4-Channel Amplifier] [Rear Speakers] REM (Remote Turn On) RED (ACC) BLACK (GND) YELLOW(B+) 5
INSTALLATION Input Connections The input source of the Smart EQ can use either the RCA preamp outputs or High Level speaker wire inputs from the head unit or Bluetooth A2DP streaming from a connected Bluetooth device. Note : User can select the audio signal source using the app on the Bluetooth connected device. The default Audio Source is the head unit. High-Level Input (speaker wire) Low Level Inputs(RCA) • Low level(RCA) input signal is preferred for best performance.
INSTALLATION Output Connections Amplifier Connection s Remote-turn on/off REM OUT has to connect to the REM IN terminal of amplifier as below. This signal is for the power on/off of amplifier. If audio signal is entered into Smart EQ, Smart EQ will give a signal in order to use for turning on the power of amplifier. [EQ Smart] [Amplifier Side] s RCA Rear/Front outputs These outputs should connect to a multi-channel amplifier that controls your full range speakers in the vehicle.
INSTALLATION Using Application • Application for Smart EQ All adjustments to this unit can be controlled by the Smart EQ App from any smartphone. User can download it from iTunes for iPhone/iPod touch or Google Play Store for Android phone. When the unit is paired and connected it will show the name of the Smart EQ. Select the input source by selecting either the Head Unit or Bluetooth Streaming button. To control the 7-band EQ move the slide bars for each frequency up and down.
INSTALLATION Using Application s "LUETOOTH PAIRING 5SER HAS TO CONNECT THE 3MART %1 TO A SMARTPHONE IN ORDER TO CONTROL THE 3MART %1 USING SMARTPHONE Pairing the Smart EQ with your device. 0AIRING IS THE PROCESS CONNECTING TWO DEVICES OVER "LUETOOTH AND ALLOWING THEM TO COMMUNICATE 9OU WILL NEED TO GO THROUGH THE PAIRING PROCESS WITH EACH DEVICE YOU USE THE 3MART %1 WITH A NEW DEVICE AND THE 3MART %1 WILL AUTOMATICALLY TRY TO RECONNECT TO THE LAST DEVICE IT WAS PAIRED WITH .
INSTALLATION Troubleshooting Problem Cause Action +12V wire not connected or incorrect Check connections for proper voltage (11~16VDC) Unit will not turn on voltage. (no power LED GND wire not connected Check connection to ground indicator) Power LED is solid in red, but no sound. Power LED is blinking. ACC wire not connected. Check connection to ACC line. REM OUT wire not connected. Check the REM connection between Smart EQ and amplifier. Audio out wire not connected.
INSTALLATION Specifications Dimensions(WxDxH) Ę 7” x 4.1” x 1.2” (177 x 103.
INSTALLATION Compliance ICC Compliance This Class [B] digital apparatus complies with Canadian ICES-003. FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause un-desired operation.
INSTALLATION One-Year Limited Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp.
Notes
Notes
Dual Electronics Corp. Toll Free: 1-866-382-5476 Monday-Friday, 9AM-5PM, EST www.axxeraaudio.com ©2014 Dual Electronics Corp.
