Installation Instructions / Warranty ThermoBalance II Deck Valve Metris S 06401XX0 Metro E 06452XX0 C Lever 06456XX0 Focus S 06405000 Solaris E 06450XX0 Stratos E 06451XX0 Talis S 06453XX0 C Cross 06454XX0 C Scroll 06455XX0 Allegro² E 04185XX0 Metro² E 04198XX0 Solaris² E 04172XX0
ThermoBalance II Deck Valve 06401XX0 06405000 06450XX0 06451XX0 06452XX0 06453XX0 Metris S Focus S Solaris E Stratos E Metro E Talis S 06454XX0 06455XX0 06456XX0 04172XX0 04185XX0 04198XX0 C Cross C Scroll C Lever Solaris² E Allegro² E Metro² E 06401XX0 06405XX0 06450XX0 06451XX0 06452XX0 06453XX0 06454XX0 06455XX0 06456XX0
04172XX0 04185XX0 04198XX0 Technical Specification Recommended pressure Maximum hot water temp. Recommended hot water temp. Flow rate @ 44 PSI Safety stop 1/2" female NPT inlets Maximum mounting surface thickness Hole size in mounting surface 45 - 72 psi 165° F* 120° - 140° F* 8 gpm 100° F 1 3/8" 2 3/8" *Know and follow all applicable local plumbing codes when setting the temperature on the water heater.
Install the rough Remove the upper mounting ring. Screw the lower mounting ring and washer to their lowest position. Insert the rough up through the hole. Install the upper mounting ring. Tighten it as far as it will go without forcing it. upper mounting ring sealing ring washer lower mounting ring Rest the rough on the mounting surface. Tighten the lower mounting ring and washer. Tighten the tensioning screws. washer lower mounting ring tensioning screws Install the plaster shield.
Install the hot and cold water supply lines* Wrap the threads on the hot and cold supply pipes with Teflon tape. Install the hot and cold supplies to the corresponding inlets. If the supplies are not connected to the correct inlets, the valve cannot function properly! hot inlet cold inlet Install the outlet lines* Wrap the threads on the outlet lines with Teflon tape. Install the lines to the outlets. If only one outlet is to be used, do not plug the second outlet. Tie the two outlet lines together.
Install the valve trim Remove the plaster shield. Push the escutcheon over the valve. Install the handle. Tighten the screw with a 3 mm Allen wrench. The screw must engage the slot on the cartridge. Justify the handle. Set the high temperature limit stop, if required. slot Justify the handle Turn the water on to the tub spout or handshower. Place a thermometer in the water stream. Turn the temperature control knob until the output water temperature is 100°F. Turn the water off.
Hold the handle lever in one hand. With the other hand, turn the temperature control knob until the 100° mark is next to the indexing mark on the handle. Install the handle on the valve. Tighten the screw. Set the high temperature limit stop (optional) Turn the water on to the tub spout or handshower. Use a 3 mm Allen wrench to loosen the handle screw. Remove the handle from the valve. Carefully remove the retainer clip and the limit stop ring (1).
Maintenance: Clean the filters CAUTION: Turn off the water at the main or with the service stops, before opening the valve. Remove the handle and escutcheon. Grasp the wrench flats on the cartridge stop unit with a wrench. Hold the stop unit still with one wrench. Use a second wrench or a 17mm deep socket wrench to unscrew and remove the thermostatic cartridge. Failure to hold the stop unit steady while unscrewing or replacing the thermostat cartridge will result in damage to the stop unit.
Justify the handle. User instructions From the off position, turn the diverter lever clockwise or counter-clockwise to obtain water from either of the two functions. Turn the temperature control knob clockwise to make the water cooler. Turn it counter-clockwise to make the water warmer. When turning the knob counter-clockwise, it will stop when the output water is 100°. To obtain water hotter than 100°, push downward on the temperature control knob and continue turning it counter-clockwise.
Replacement parts 5 4 3 6 12 7 10 9 8 2 1 13 11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 cartridge with shutoff unit 88586000 thermostat cartridge 94282000 Solaris handle 88528XX0 Stratos handle 88543XX0 Metro handle 88548XX0 Talis handle 88549XX0 Cross handle 88608XX0 Scroll handle 88609XX0 Lever handle 88610XX0 Metris handle Focus handle escutcheon Allegro² handle Metro² handle XX = color code 00 = chrome 62 = oil rubbed bronze 82 = brushed nickel 83 = polished nickel 10 14
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instructions.
