Installation Instructions / Warranty Citterio M 34444XX1
Axor Citterio M Trim, 4-Hole Roman Tub Set 34444XX1 Installation Considerations • For best results, Hansgrohe recommends that this unit be installed by a licensed, professional plumber. Technical Information Recommended water pressure 14.7 - 72.5 psi Max. water pressure 147 psi Recommended hot water temp. 120� - 140� F* Max. hot water temp 176�F* Max. flow rate 5.8 gpm Handshower flow rate 2.5 gpm *Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.
Installation Turn the water off at the main (1). Remove the plaster shields from the valves and spout tee (2). Remove the hot and cold cartridges from the rough. Hold the valve still with a 25 mm wrench while unscrewing the cartridge with a 17 mm wrench. Discard the old cartridges.
Install the new cartridges. The cold cartridge is marked with notches on the wrench flats. Hold the valve steady with a 25 mm wrench while tightening the cartridge with a 17 mm wrench. Take care not to overtighten or damage to the valve may result! Place the square escutcheon over the valve. Place the nut over the valve and escutcheon. Tighten the nut with the special tool. Install the round flange.
Install the handle snap connectors on the valve stems. Tighten the screws. Make sure that the valve stems are in the off position. Turn the hot valve stem clockwise and the cold valve stem counter-clockwise. Position the handle and color ring over the stem. Press the handle firmly into place.
Make sure that the handles are parallel. If one is not, remove it (1), turn it slightly (2), and push it back into place (3). 1. 2. Remove the spout tee plug using a 27 mm wrench. 3.
Grease the diverter o-rings with the enclosed lubricant. Push the diverter firmly into the spout tee. Place the sealing ring, escutcheon, and flange over the diverter stem. Push the spout into place. Tighten the spout screw with a 3 mm Allen wrench. Install the diverter knob.
Grasp the Secuflex hose and pull it up and away from the mounting surface. Lubricate the o-rings with silicon spray. Pull the Secuflex hose out until the white plastic nut clears the mounting surface and the metal high pressure hose can be grasped (1). 3. Unscrew the Secuflex hose from the white plastic nut (2). Remove the plaster shield from the Secuflex hose (3). 1. 2.
Remove the plug from the end of the high pressure hose (1). 1. Insert the check valve into the hose, o-ring side first (2). The arrow will indicate the direction of the water flow. Install the handshower hose on the high pressure hose (3). 2. 3. Lubricate the handshower hose and the ends of the Secuflex hose with the silicon spray. Feed the handshower hose up through the Secuflex hose (1). Connect the Secuflex hose to the white plastic nut (2). 1. 2.
Remove the nut and insert from the handshower holder (1). Compress the Secuflex hose until the end of the handshower hose is exposed (2). Feed the handshower hose through the handshower holder. Snap the two halves of the insert around the hose. Slide the nut over the end of the hose (1). Push the insert down into the handshower holder. Screw the nut onto the handshower holder (2). 1. 2. 1. 2. Remove the o-rings from the bottom of the Secuflex hose.
Push the escutcheon down over the handshower holder. Turn it clockwise, so that it threads down over the shank. Place the screen washer in the end of the hose (1). Install the handshower (2). User Instructions Pivot the handle forward to turn the water on -- counterclockwise for hot, clockwise for cold.
25 1 2 22 3 10 21x1,5 11 5 12 23 19 6 17 16 18 21 20 53x1 24 38x2 13 26x2 60x3 15 60x2,5 14x2,5 7 8 22x2 23x2,5 9 4 12 9x2,5 11x2 14
Replacement Parts 1� 2� 3� 4� 5� 6� 7� 8� 9� 10� 11� 12� 13� 14� 15� 16� 17� 18� 19� 20� 21� 22� 23� 24� 25� spout cpl. 98997XX0 diverter knob 96774XX0 aerator cpl.
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B.
www.hansgrohe-usa.com US - Installation Instructions • Part No. 90457121 • Revised 05/2008 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel.
