Installation Instructions / Warranty Vertical Spray Bidet Fitting Rough 1322X181 Axor Trim Kits Citterio cross handle 39224XX0 Citterio lever handle 39225XX0 Starck 10220XX0 Steel 35220800 Uno 38220XX0 Terrano cross handle 37224XX0 Terrano lever handle 37225XX0 Carlton cross handle 17224XX0 Carlton lever handle 17225XX0 Phoenix cross handle 17226XX0 Phoenix lever handle 17227XX0 Montreux 16521XX0
Technical Specification Recommended operating pressure Recommended hot water temp. Flow rate Hole sizes valves transfer valve pull rod 45 - 80 psi 120oF - 140oF* 2.2 gpm 1 1/4” 1 1/4” 3/8” min. *Know and follow all applicable local plumbing codes when setting the temperature on the water heater. In Massachusetts, the water heater may be set no higher than 112oF. Important: This valve is for use on vertical spray bidets only. It is not suitable for use on other fixtures.
Rough-in Installation Instructions Install the transfer valve Install the y-connector and seal on the bottom of the transfer valve. Screw the connecting hoses to the y-connector. Screw the elbow connector to the outlet port on the side of the transfer valve. The arrow on the elbow connector indicates the direction of the water flow. It should point downward. Screw the spray hose to the elbow connector.
Install the pop-up guide assembly Remove the nut, metal washer, and sealing washer from the pop-up guide assembly. Position the pop-up guide and sealing washer on the proper hole on the bidet. Install the metal washer and nut. Install the pop-up drain plunger Remove the plunger assembly. Unscrew the drain outlet flange from the tee. Unscrew the tailpiece from the tee. Wrap the threads with Teflon tape and replace. Install the white, flexible sealing gasket on the flange. Sith it in the sink outlet.
Attach the swivel connector to the end of the horizontal rod. Attach the swivel connector to the end of the vertical rod. Position as desired, and tighten with a small, flathead screwdriver.
Trim Kit Installation Install the valves: Starck and Citterio only Remove the valve mounting nuts from the valves. Push the valves up into the holes. Install the mounting plates on the holes. Tighten the tensioning screws. Install the valves: all other styles Remove the plaster shields, mounting plates, and stop rings from the valves. Push the valve up through the hole. Slide the stop ring onto the valve. Install the mounting plate. The stop ring will stop it at the proper height.
Install the transfer valve trim Screw the sleeve down onto the transfer valve. Push the handle over the stem and secure it with the screw. Line up the locator tab on the screw cover with the notch in the handle. Press down firmly. Install the handles Carlton/Phoenix/Terrano Screw the escutcheons down over the mounting plates. Position the handle over the valve with the lever or cross in the desired off position. Hold the lever or cross steady with one hand.
Citterio / Starck Position the handle over the valve. While holding the cross or lever steady with one hand, use the other hand to thread the escutcheon down over the mounting plate. Montreux Position the handle over the valve. While holding the cross steady with one hand, use the other hand to turn the escutcheon clockwise to thread it onto the valve. Lightly grease the o-rings. Press the hot and cold caps into place on the handles.
Replacement Parts - Rough 4 1 8 3 6 2 5 7 Replacement Parts - Trim 17 14 13 39 21 22 18 11 12 15 23 10 19 25 24 9 39 16 26 20 9
29 32 33 27 34 28 35 31 30 36 37 38 36 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 10 transfer valve connection hose spray hose pull rod aerator drain hinged connector plastic screw and filter valve set for Starck, Citterio hot cartridge cold cartridge valve set hot cartridge cold cartridge fixing set sleeve transfer valve handle Starck handle Citterio cross, cold hot Citterio lever, cold hot Steel handle color ring set escutcheon Uno handle color ring set escutcheon 886
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B.
