Code 502701 Router Elevator Fast accurate height adjustment from above the table AT&M: 16/03/2015
Index of Contents Page No. Index of Contents Declaration of Conformity What’s included Specifications Accessories Dimensions Position Diagram Illustration & Description of the Router Elevator Fitting the Router and the Cutters Setup/Operating Instructions Maintenance Parts Drawing Parts List 02 02 03-04 04 04 05 06-07 08-09-10-11 11 12 13 14-15 Copyright This product has been wholly designed by Axminster Power Tool Centre Ltd who have exclusive use of the design.
What’s Included Quantity Item 1 off. Router Elevator with Measurement Dial (router mounting plate and table Insert fitted) 1 off. Winding Handle 1 off. Packet containing:6 off. M6 Grub Screws 2 off. M6 Countersunk Bolts 1 off 4 off. Nippled ‘Y’ wrench (for Table Insert) Hex Keys 6mm/4mm/3mm/2.
What’s Included Having unpacked your machine and its accessories, please check the contents against the equipment list ”What’s in the box”, if there are any discrepancies, please contact Axminster Tool Centre using the procedures laid down in the catalogue. Please dispose of the packaging responsibly; much of the material is bio-degradable. on top line and prolong its life. Keep this Instruction Manual readily accessible for any others who may also be required to use the machine.
Dimensions Position Diagram 05
Illustration & Description of the Router Elevator Lock Turn the handle clock-wise to raise the table Locking the table in position 38mm Table insert x2 Grub screw hole for support functions x4 Grub screw hole for levelling function x2 Countersunk hole Winding handle Machine table Drive mechanism Rise and fall platform Reference marker for the measurement dial Measurement dial Table locking mechanism Depth stop nut 06 Threaded rod
Illustration & Description of the Router Elevator Lock Un-Lock Insert the Nippled “Y” wrench into the table insert and turn un-clockwise to remove the insert Remove the table insert and place safely aside Machine table Locking mechanism Idler sprocket Sprocket Drive sprocket Clamping lug Universal router mounting plate Chain Table locked Table un-locked 07 Locking mechanism
Fitting the Router and the Cutters Introduction The information below is reproduced from the Axminster universal base plate fitting instructions and the hole layout on the router elevator base plate is identical. Hole numbers, screw types and how many required are given for mounting different router models to the router elevator base plate.
Fitting the Router and the Cutters Universal Base Plate 176mm 7mm A B M4x10mm M4x12mm 1 C UNF10 x1/2” D M5x16mm E M5x20mm F M6x16mm G M6x30mm 3 2 09 H I M6x12mm M4x6mm
Fitting the Router and the Cutters IN ORDER TO FIT SOME OF THE ROUTERS TO THE ELEVATOR AND ACHIEVE UNRESTRICTED MOVEMENT, IT MAY BE NECESSARY TO REMOVE THE HANDLES; PLUNGE THE ROUTER BODY TO DEPTH, ETC., ETC. Lower the table to almost its fullest extent. Using the Allen key provided loosen the bolts and therefore the lugs holding the universal mounting plate (UMP) in position and remove. (See Figs 1 and 2).
Fitting the Router and the Cutters NOTE. If you find that some of your cutters are ‘borderline’ for ‘reach’ or the length of shank remaining in the collet is approaching the minimum limit, may we suggest the purchase of the short collet extension Axminster No. 211367. (See Page 4) to orientate the router so that the power switch is easily accessible when the router elevator is fitted to the work platform. When everything is assembled to your satisfaction.
Maintenance The router elevator requires minimum maintenance, but you are advised to observe the following points:1. Keep the elevator clean. Ensure that dust/chips etc., are cleaned away at the end of a work session. 2. Do not allow a build up of dust/chips etc., between the machine table and the rise and fall platform, or under the machine, where it may foul the chain drive. 3. If the winding action becomes ‘lumpy’ check that there is no debris caught in the chain, or compressed onto a sprocket. 4.
Parts Drawing 13
Parts List 14
Parts List 15
The UJK technology brand was launched by us in 2012 with the intention of encompassing a range of carefully selected products that we held in particular high esteem. Many of these products are designed by us and manufactured by one of our most trusted Far Eastern suppliers. The range includes routing, measuring and wood jointing products and has already proven extremely popular.
