Specifications
Chip Extraction
Wood Waste Extraction
110
2 2
Not only does the introduction of an efficient dust or chip extraction system reduce this potential
health hazard, but it keeps the workshop cleaner and generally makes working with wood in a
confined space a much more enjoyable activity. The choice of the correct type of extractor for
any particular application can be a bit confusing, with apparently conflicting requirements for
collecting different types of waste from a wide variety of woodworking machinery. For more
information regarding the potential risks of wood dusts, please visit:
http://www.hse.gov.uk/woodworking/index.htm
and
http://www.hse.gov.uk/coshh/industry/woodworking.htm
As an aid to selecting a suitable extractor we have introduced the following performance rating
guide to give a quick indication of the type of waste that each extractor is designed to handle. If
you are still unsure of suitability please contact our Specialist Sales Dept on 03332 406406
Extraction Performance Ratings (guidance only)
1 - Chippings only
2 - Chippings and sawdust (with fine filter option fitted)
3 - Chippings, sawdust and sanding dust
4 - Chippings, sawdust, sanding dust and MDF dust
These extractors are powered by centrifugal fans which draw a large volume of air through the inlet hose and discharge it through the fabric filter bag situated on the top of the machine. The waste falls
into the lower bag which will either be a fabric or plastic waste sacks, where applicable. Although these machines generate a large volume of airflow the pressure rise is low which makes them unsuitable
for operating with small diameter inlet hoses. A reduction below 3” diameter is not recommended. The mesh size of the filter bag has to be relatively coarse in order to allow the high volume of air to pass
through and thus the extractor is not suitable for filtering out the very fine dust produced by sanding machines. The cartridge filters available for most of the models will improve the level of filtration and
are nowadays fitted with deep pleats to avoid any loss of air flow. Generally suitable for collecting chippings and larger particle size sawdust from machines equipped with 3”, 4” or larger diameter outlets. For
the best results we recommend using an extractor with higher airflow than is required by the machine you are connecting it to.
axminster.co.uk/signup for our exclusive email offers
Can be used suspended from a wall,
brackets are provided
This extractor can be used in small home workshops for
common wood machining tasks where a higher airflow than
provided by a vacuum extractor is required. The quiet running
induction motor provides plenty of power to extract from many
small workshop machines. The inlet diameter is 100mm(4”), the
outlet into the bag is 100mm(4”) and the airflow is sufficient to
handle the majority of waste likely to be produced in the small
home workshop. A useful feature is that it can be used either
on the floor or suspended from a sturdy wall using the two
hanging brackets provided. A useful grab handle and castors
allow easy mobility. Hose not supplied. See extraction hose
selection for further details. Please note that this is a chippings
extractor and should not be expected to collect fine dust. As
with all the high volume low pressure airflow machines, the
inlet should not be restricted to below 75mm diameter and the
bag should be emptied regularly. Spare bag provided.
Performance Rating 1
Axminster Hobby Series
AWDE5002 Extractor
Quick Release 100mm Hose Clip (Pair) £9.95 £8.29 210323
Inc.vat Ex.vat Code
Base fitted with castors
and grab handle for
easy mobility
Inlet diameter
is 100mm
Quiet and efficient, will not
offend your neigbhours
850m³/hr air flow,
750W, 230V 1ph motor
Bag filter
efficiency 30
micron
Accessory
£154.96
Code: 501262
Ex.vat: £129.13
£184.96
Code: 501263
Ex.vat: £154.13
A chip and coarse dust extractor for extracting from hobby
series saws, planers, bandsaws and similar machines in a small
workshop. Equipped with two cloth bags, the top one acting
as the filter and the lower one for collecting the waste. Power
comes from a 750W induction motor equipped with a no-volt-
release switch and emergency stop button. If required, the cloth
collection bag can be replaced with plastic waste sacks, which
can be more convenient for storage of waste prior to disposal.
An unusual feature of this extractor is the floor sweeping
attachment which fits to the base of the machine, allowing
the extractor to be wheeled around the workshop, collecting
waste as it goes. There is a fine filter bag available for use when
collecting medium sized dust particles, or alternatively, an
optional fine dust cartridge filter can be fitted. (N.B.You must
use plastic waste sacks with the fine filter bag or cartridge
filter) The machine is supplied with approximately 600mm
length of inlet hose; additional lengths of 100mm hose are
available separately. This machine uses waste sack size - 560
x 915mm (340068).
Axminster Hobby Series
AWEDE2 Extractor
Fine Filter Bag £10.45 £8.71 500079
Cartridge Filter £129.96 £108.30 700344
Inc.vat Ex.vat Code
560 x 915mm Waste Sack Red (Pkt 10) £11.46 £9.55 340068
Quick Fit Metal Strap to 1140mm(45”) £7.45 £6.21 800425
Inc.vat Ex.vat Code
Replacement Filters
Accessories
Uses waste sack
size - 560 x 915mm
(340068)
850m3/hr air flow,
0.75kW 230V 1ph
induction motor
Can be upgraded
with a fine filter
cartridge
100mm hose fits
directly to many
saws, planers,
bandsaws etc
Wheeled base and
grab handle for
ease of movement
An attachment
provided to enable
easy floor cleaning
of wood chips
Bag filter
efficiency 30
micron
Dust Extraction.indd 110 27/11/2014 16:03