Specifications

Extraction Accessories
120
Free delivery on orders over £50 (UK mainland only) Orders UNDER £50 P&P £4.95
2
• Lengths of high quality wire
reinforced 100mm hose
• Rubber end cuffs to suit
extraction outlets 100-110mm
• Ideal for mobile workshop
chip and dust extractors
Axminster Flexible
Extraction Hose Kit
Axminster 4m x 100mm Extraction Hose Kit £74.95 £62.46 211597
Axminster 2m x 100mm Extraction Hose Kit £44.95 £37.46 501082
Inc.vat Ex.vat Code
• Keep hoses, ropes and extension
leads stowed away and tidy
• 100mm diameter curve
• Use to support dust extractor hose
• Supplied with three wall plugs and
screws
Hose Hook
Hose Hook £2.26 £1.88 600684
Inc.vat Ex.vat Code
• Kit of components
• Useful when connecting up machines to an extraction system
• 2 x 3m lengths of 100mm diameter exible hose.
• Table saw dust hood
• 100mm Y tting
• 10 x 100mm pipe clamps
• 4 x 100mm blast gates
• Floor sweeper
• 150mm jointer dust hood
100mm Dust Extraction Accessory Kit
100mm Extraction Kit £109.96 £91.63 410064
Inc.vat Ex.vat Code
• Especially for the smaller
workshop
• Ducting package complete
with elbows, blast gates and
adaptors
• 8 three foot lengths of tube
(63mm diameter)
• 4 x tee joints
• 3 x 45° joiners
• 2 x 90° elbows
• 16 x pipe joiners
• 5 x plastic blast gates
• 10 x wall clips
• 100mm to 63mm adaptor
• Additional parts available
separately
63mm Dust Extraction Kit
Dust Extraction Kit 63mm £104.95 £87.46 410063
915mm Lengths of 63mm Pipe (4 Pack) £33.46 £27.88 410069
90° Elbow for 63mm DEK £4.96 £4.13 410066
Pipe Joiner for 63mm DEK £1.96 £1.63 410070
45° Elbow for 63mm DEK £2.46 £2.05 410065
Tee Joiner for 63mm DEK £4.96 £4.13 410072
Blast Gate for 63mm DEK £4.45 £3.71 410067
Securing Clips 63mm (10) £6.96 £5.80 410068
100mm to 63mm Reducer £2.95 £2.46 410071
Inc.vat Ex.vat Code
Dust Extraction kit £179.95 £149.96 210695
100mm x 910mm clear pipe £16.96 £14.13 210697
Joining Splice £2.95 £2.46 210698
45° Elbow £3.96 £3.30 210699
Wall Clip £1.26 £1.05 210700
Inc.vat Ex.vat Code
The Numatic vacuum attachment kit has been designed for
use with the Axminster 63mm Dust Extraction Kit. It allows any
Numatic vacuum machine from a “Henry” upwards to be used
to provide the vacuum to this 63mm system. It simply fits into
a DEK “T” junction and provides a threaded connector for the
2.5m double threaded Numatic hose which is part of the kit.
This hose has the 51mm female thread allowing it to be fitted
to any standard Numatic vacuum machine. For the purpose that
the Axminster DEK is intended, even a Henry would provide
adequate air flow and, when used with HepaFlo bags, top grade
filtration as well. Simple to fit and very effective.
Numatic 63mm
Dust Extraction Kit Attachment
63mm Dust Extraction Kit Attachment £59.95 £49.96 501270
Inc.vat Ex.vat Code
Workshop Metal Ducting Kit
A package of dust and chip extraction metal ducting, enough to
extract from four machines, consisting of:
2 x 2m 150mm Duct
1 x 150mm 90° Elbow
2 x 150-100mm 45° Branch Tee
1 x 150-100mm Reducer
3 x 2m 100mm Duct
10 x 1m 100mm Duct
2 x 150mm Joiners
3 x 100mm Joiners (packs of 5)
2 x 90° 100mm Elbow
4 x 45° 100mm Elbow
2 x 100-100mm 45° Branch Tee
1 x 100mm Fixture Joiners
(pack of 5)
20 x 100mm Suspension Ring
Fixings
4 x 150mm Suspension Ring
Fixings
4 x 100mm Blast Gates
5 x 1m x 8mm Threaded Rod
24 x 8mm Threaded Back
Plates
1 x Duct Tape
Extra or additional components are available from our Metal
Ducting selection, but this kit would be enough for many small
workshops and take the guesswork out of what you may require.
Ducting lengths may be shortened with a metal cutting hack
saw. Keep the design simple and follow these rules:
• Don’t over complicate the system
• Keep transfer duct as large as the extractor will accept
• Keep exible duct to a minimum length or none at all if
possible
• Keep branches joining a duct to 45° maximum
• Fit blast gates to maximise efciency and balance to the system
Metal Ducting Kit £699.96 £583.30 717045
Inc.vat Ex.vat Code
A 100mm ducting kit with most items a home woodworker
needs to connect machines to an extractor. Comprising 8 X
910mm lengths of 100mm clear plastic duct, 2 X T junctions, 2 X
90 degree elbows, 2 X 45 degree elbows, 3 x blastgates and 16
x joiners. A pack of 10 wall brackets with screws and wallplugs
are included. All the items are available separately, enabling you
to build a system exactly how you need it. Our other accessories
such as the 990053 Y junction, 500181 Flanged Spigot and
200114 Big Mouth Dust Hood all fit this kit. Add a 410064 kit
and you will get 2 x 3m lengths of flexible hose as well as a
whole host of useful connectors and hoods. The 510412 Earth
Grounding Kit would be worth considering to protect yourself
from possible static build up. Seriously good value for money,
this kit is exactly what the home workshop requires.
100mm Dust
Extraction Kit
Dust Extraction.indd 120 27/11/2014 16:04