D.R.O. Micro Drill User manual 200021 W 2004 AXMINSTER W H I T E Part No. 200021 w w w. a x m i n s t e r. c o .
Index of Contents... Page No. Index of Contents....................................................................................................................02 Declaration of Conformity………….………........……..…………........................................03 What’s in the Box………….………........……..………….......................................................... 04 General Instructions for 230v Machines............................................................05,06 Specific Safety for Drilling Machines.........
Declaration of Conformity... W AXMINSTER W H I T E Copied from CE Certificate The undersigned, Ole Stilling authorised by Shanghai SIEG Machinery Co., Ltd No.555 Caofeng Rd, South to No.17 Bridge of Caoan Rd, Shanghai, P.R China declares that this product: Micro Mill X0 manufactured by Shanghai SIEG Machinery Co.
W What’s in the Box... AXMINSTER W H I T E Model Number: 04 X0 1 No. Micro Drill Comprising: 1 No. Headstock 1 No. Column and Work Table 1 No. Depth Collar and Ring 1 No. Star Knob (Complete with two Clamp Bushes) 1 No. Drill Chuck 1 No. Feed Handle 1 No. Chuck Key 1 No. 5.5mm & 7mm Open ended Spanner 1 No. 2mm Allen Key 1 No. 2.6mm Allen Key 1 No. 3mm Allen Key 1 No. 4mm Allen Key 1 No. Guarantee Card 1 No. Instruction Manual www.axminster.co.
General Instructions for 230v Machines... W AXMINSTER W H I T E Good Working Practices/Safety The following suggestions will enable you to observe good working practices, keep yourself and fellow workers safe and maintain your tools and equipment in good working order. ! WARNING!! KEEP TOOLS AND EQUIPMENT OUT OF THE REACH OF YOUNG CHILDREN Mains Powered Tools and Machines Primary Precautions These machines are supplied with a molded 13 Amp Plug and 3 core power cable.
W General Instructions for 230v Machines... AXMINSTER W H I T E Work Place/Environment (Continued) If you wear your hair in a long style, wearing a cap, safety helmet, hairnet, even a sweatband, will minimise the possibility of your hair being caught up in the rotating parts of the machine, likewise, consideration should be given to the removal of rings and wristwatches if these are liable to be a 'snag' hazard. Consideration should also be given to non-slip footwear, etc.
Specific Safety for Drilling Machines... W AXMINSTER W H I T E 9. NEVER remove 'flying' swarf strands from the drill whilst it is turning. 10. It is a good precaution to wear eye protection when drilling, especially using small drills, or very hard material that produces small chips. 11. It is not a good idea to wear gloves when operating a drill press. 12. After the job is completed, remove all tools and accessories from the machine, check that drill bits are still sharp and re-useable.
W Initial Assembly Instructions Continued... AXMINSTER W H I T E Assemble the Depth (4) collar and ring (3) onto the column firmly. (Fig 2) Insert the Star Knob (2) complete with the two clamp bushes (21, 22) into the headstock location. Make sure the two cut outs are lined up towards the rear so as to allow the column to slide past them. Slide the headstock onto the column (6), you can see down the hole to make sure the clamp cut outs mentioned above are clear of the column.
Illustration and Parts Description...
Illustration and Parts Description... W AXMINSTER W H I T E On/Off rocker switch On Fig 4 Off Fig 4a Depth collar & ring Fig 4b Fine feed knob Speed control knob Fig 4c Fig 4d Fuse Speed control panel 10 Knurled knob www.axminster.co.
Illustration and Parts Description... W AXMINSTER W H I T E Fig 5 Digital display Min/in Press “mm/in” button to select metric or imperial readings. On/Off For normal drilling operations press the ON/OFF switch first, and then press the “ZERO” button. Plus & Minus The readings on the display can be amended at any time by pressing “plus” or “minus” buttons. Fig 5b Fig 5a Removing battery cover 1.
W Operation of the Micro Drill... AXMINSTER W H I T E Setting headstock level (Figs 1 & 2) Loosen the hex screw securing the depth collar (4) and adjust to the height required to prevent damage to the headstock by sudden dropping of the headstock. Adjusting the headstock height (Fig 2) Loosen the Star knob (2) whilst supporting the weight and move to the desired height.
Adjusting the Spindle Speed... W AXMINSTER W H I T E Fig 6 Small pulley Motor mount Fig 8 Pulley Loosen and remove the two screws on the belt cover. Fig 7 Large pulley Remove the belt cover. Move the belt to the required ratio. There is no need to slacken the motor mounts to change the speed. Routine Maintenance... ! WARNING!! Disconnect the machine from the Mains Supply Excessive dust in the motor can cause excessive heat to develop.
W Parts Breakdown for the Micro Drill... AXMINSTER W H I T E 14 www.axminster.co.
Parts List for the Micro Drill...
W AXMINSTER W H I T E Part no. 200021 Axminster Devon EX13 5PH UK FREEPHONE 0800 371822 2004 www.axminster.co.
