AXIS Q6045-E Mk II PTZ Dome Network Camera User Manual
About this document This manual is intended for administrators and users of AXIS Q6045-E Mk II PTZ Dome Network Camera, and is applicable to firmware 5.70 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be beneficial, for developing shell scripts and applications.
Safety This product complies with IEC/EN/UL 60950-1 and IEC/EN/UL 60950-22, Safety of Information Technology Equipment. The product shall be grounded either through a shielded network cable (STP) or other appropriate method. The power supply used with this product shall fulfill the requirements for Safety Extra Low Voltage (SELV) and Limited Power Source (LPS) according to IEC/EN/UL 60950-1. Battery The Axis product uses a 3.
AXIS Q6045-E Mk II PTZ Dome Network Camera Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Message Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS Q6045-E Mk II PTZ Dome Network Camera Table of Contents Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset to Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Check the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS Q6045-E Mk II PTZ Dome Network Camera Safety Information Safety Information Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE TICE NO Indicates a situation which, if not avoided, could result in damage to property.
AXIS Q6045-E Mk II PTZ Dome Network Camera Hardware Overview Hardware Overview NOTICE TICE NO Make sure the dome is attached in operation mode, otherwise focus may be affected. 5 6 7 8 9 11 4 1 2 1 2 3 4 5 6 7 8 9 10 11 3 Hook for safety wire Network connector (High PoE) Ground screw Unit holder (3x) Part number (P/N) & Serial number (S/N) Power button Heater Control button Status LED indicator SD card slot (SDHC) Dome Connectors and Buttons For technical specifications, see page 64.
AXIS Q6045-E Mk II PTZ Dome Network Camera Hardware Overview NOTICE TICE NO The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall be intended for their specific use. Make sure that the network devices are installed in accordance with the manufacturer’s instructions. For information about regulatory requirements, see Electromagnetic Compatibility (EMC) on page 2 .
AXIS Q6045-E Mk II PTZ Dome Network Camera Hardware Overview Midspan LED Indicators LED Color Indication Port Unlit No camera connected. Green Steady when camera connected, normal operation. Green, flashing Slow flash when overcurrent or short circuit condition on the port. Green, flashing Fast flash when input voltage is out of range or other internal error. Green Steady when AC power input connected.
AXIS Q6045-E Mk II PTZ Dome Network Camera Access the Product Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are • Internet Explorer® with Windows® • Safari® with OS X® • ChromeTM or Firefox® with other operating systems. See Technical Specifications on page 64.
AXIS Q6045-E Mk II PTZ Dome Network Camera Access the Product Set the Root Password To access the Axis product, you must set the password for the default administrator user root. This is done in the Configure Root Password dialog, which opens when the product is accessed for the first time. To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate.
AXIS Q6045-E Mk II PTZ Dome Network Camera Access the Product The product’s heater is controlled by the ambient temperature and is turned on and off automatically. If required, the heater can be activated manually by clicking the Heater button. To show the button, go to Setup > Live View Config. Under Action Buttons, select Show heater button and specify the number of minutes the heater should be activated. Enable or disable the Gatekeeper by selecting On or Off from the drop-down list.
AXIS Q6045-E Mk II PTZ Dome Network Camera Access the Product Click the Emulate joystick mode button and click in the image to move the camera view in the direction of the mouse pointer. Click the Center mode button and click in the image to center the camera view on that position. The center mode button could also be used to zoom in on a specific area. Click in the image and drag to draw a rectangle surrounding the area to be magnified. To zoom out, rotate the mouse wheel.
AXIS Q6045-E Mk II PTZ Dome Network Camera Media Streams Media Streams The Axis product provides several video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, and to the list of available stream profiles. Other applications and clients can access video streams directly, without going via the Live View page. How to Stream H.264 H.
AXIS Q6045-E Mk II PTZ Dome Network Camera Media Streams The AMC Control Panel can be used to configure various video settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: • Windows Control Panel (from the Start screen or Start menu) • Alternatively, right-click the video image in Internet Explorer and click Settings.
AXIS Q6045-E Mk II PTZ Dome Network Camera Media Streams Note • = IP address • The Axis product supports QuickTime 6.5.1 and later. • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS Q6045-E Mk II PTZ Dome Network Camera Set Up the Product Set Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to all settings except System Options See also the online help .
AXIS Q6045-E Mk II PTZ Dome Network Camera Video Video It is possible to configure the following video features in your Axis product: • Video stream. See page 18. • Stream profiles. See page 19. • Camera settings. See page 20. • Overlay image. See page 21. • Privacy mask. See page 23. Set Up Video Streams To set up the product’s video streams, go to Video > Video Stream. The video stream settings are divided into the following tabs: • Image. See page 18. • H.264. See page 19. • MJPEG.
AXIS Q6045-E Mk II PTZ Dome Network Camera Video H.264 H.264, also known as MPEG-4 Part 10/AVC, is a video compression standard that provides high quality video streams at low bit rates. An H.264 video stream consists of different types of frames such as I-frames and P-frames. An I-frame is a complete image whereas P-frames only contain the differences from previous frames. The H.264 stream settings can be configured from the Video > Video Stream page. Select the H.264 tab.
AXIS Q6045-E Mk II PTZ Dome Network Camera Video To select a default stream profile for the Live View page, go to Setup > Live View Config. Camera Settings The Video > Camera Settings page provides access to advanced image settings for the Axis product. Image Appearance To change Image Appearance go to the menus under Setup > Video > Camera Settings. Increasing the Color level increases the color saturation. The value 100 gives maximum color saturation and the value 0 gives minimum color saturation.
AXIS Q6045-E Mk II PTZ Dome Network Camera Video Max gain - Measured in decibels (dB), gain describes the amount of amplification applied to a signal, in this case the visual information in the image. A high level of amplification may provide a better image in very low light situations. A high gain will also increase the amount of image noise. Exposure zones - This settings determines which part of the image is used to calculate the exposure. For most situations, the Auto setting can be used.
AXIS Q6045-E Mk II PTZ Dome Network Camera Video 5. Define text overlay characteristics in the relevant fields. 6. Click Save. To modify the date and time format, go to System Options > Date & Time. See Date & Time on page 50. Displaying the Pan Position as a Text Overlay It may be useful to retrieve, for instance from a recorded video, the pan position (in degrees) in which an event has taken place. This can be obtained by including the pan position in the image as a text overlay, using a modifier.
AXIS Q6045-E Mk II PTZ Dome Network Camera Video To display the overlay image: 1. Go to Video > Video Stream and select the Image tab. 2. Under Overlay Settings, select Include overlay image at the coordinates. 3. To control the image’s position, enter the X and Y coordinates. The X=0 and Y=0 position is the top left corner. If a part of the image is positioned outside the video image, the overlay image will be moved so that the whole image is visible. 4. Click Save.
AXIS Q6045-E Mk II PTZ Dome Network Camera Configure the Live View Page Configure the Live View Page You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features of the Live View page. • Stream Profile. See page 19. • Default Viewer for Browser. See page 24. • Viewer Settings. See page 24. • Action Buttons. These are the buttons described in Controls on the Live View Page on page 11 . • User Defined Links. See page 25.
AXIS Q6045-E Mk II PTZ Dome Network Camera Configure the Live View Page User Defined Links To display user-defined links in the Live View page, select the Show custom link option, give the link a name and then enter the URL to link to. When defining a web link do not remove the 'http://' from the URL address. Custom links can be used to run scripts or activate external devices connected to the product, or they can link to a web page.
AXIS Q6045-E Mk II PTZ Dome Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) Preset Positions A preset position is a saved view that can be used to quickly steer the camera to a specific position.
AXIS Q6045-E Mk II PTZ Dome Network Camera PTZ (Pan Tilt Zoom) The product can be mounted in three different horizontal directions. This may cause the view from Pan 0° to be changed from the original view. Click Set new Pan 0° to set the pan coordinate system to zero in the current direction. Set new Pan 0° can be useful for instance when re-installing the product after maintenance. Autotracking The Axis product can detect movement in the field of view, for example a moving vehicle or person.
AXIS Q6045-E Mk II PTZ Dome Network Camera PTZ (Pan Tilt Zoom) 2 1 0° -90° 0° B 90° -180°/180° -90° A A 90° -180°/180° B Top view A B Pan limit start Pan limit end Gatekeeper The Active Gatekeeper monitors an area such as an entrance gate. When motion is detected in the monitored area, the Gatekeeper will, depending on configuration, steer the camera to a selected preset position or start autotracking from a selected preset position.
AXIS Q6045-E Mk II PTZ Dome Network Camera PTZ (Pan Tilt Zoom) To modify or remove guard tours, go to PTZ > Guard Tour, select the guard tour in the Guard Tour List and click Modify/Remove. Note For products that support Limited Guard Tour, the product has a fixed minimum view time For more information see the online help .
AXIS Q6045-E Mk II PTZ Dome Network Camera PTZ (Pan Tilt Zoom) When Enable E-flip is selected, as it tilts down and continues to pan backwards, the Axis product will automatically correct the view and flip it 180 degrees. The left limit must be set to –180 degrees and the right limit to 180 degrees for e-flip to work. Near focus limit is used to prevent the camera from autofocusing on objects close to the camera.
AXIS Q6045-E Mk II PTZ Dome Network Camera PTZ (Pan Tilt Zoom) Note Disabling PTZ controls will not affect preset positions. For example, if the tilt control is disabled, the product can still move to preset positions that require a tilt movement. Control Queue Note • The administrator can enable and disable PTZ controls for selected users. • To identify different users in the viewer group, cookies must be enabled on the client. • The Control queue polltime is measured in seconds.
AXIS Q6045-E Mk II PTZ Dome Network Camera Detectors Detectors Shock Detection Enable Shock Detection from the Detectors menu. Shock detection is used, for example, to generate an alarm if the product is hit by an object or if the product is tampered with. Use the Shock sensitivity slider to adjust the sensitivity level at which the product should send an alarm. Low sensitivity value implies that the product will generate an alarm only if the hit is powerful.
AXIS Q6045-E Mk II PTZ Dome Network Camera Detectors Parameter Object Size History Sensitivity Description Object size relative to window size. Object memory length. Difference in luminance between background and object. High level (100%) Only very large objects trigger motion detection. An object that appears in the window triggers motion detection for a long time before it is considered as non-moving. Ordinary colored objects on ordinary backgrounds trigger motion detection.
AXIS Q6045-E Mk II PTZ Dome Network Camera Detectors 1. Choose Area of interest from the drop-down list. Set the virtual area to detect if an object has disappeared from this area of interest. Important When configuring Object size the view shall be zoomed out to Wide position. 2. Choose Object size from the drop-down list. Set the size limits of the object that should be detected. The camera will detect any object whose size falls in between the minimum (blue shape) and maximum (white shape) range. 3.
AXIS Q6045-E Mk II PTZ Dome Network Camera Detectors 3. Use the Sensitivity slidebar to define how sensitive the detection should be. The lower sensitivity selected on the Sensitivity bar, the greater difference in luminance is needed between the object and the background for the detector to be activated. See the online help for more information. Fence Detector Fence Detector is used to trigger an alarm if an object crosses a virtual line.
AXIS Q6045-E Mk II PTZ Dome Network Camera Detectors 2. Choose Object size from the drop-down list. Set the size limits of the object that should be detected. The camera will detect any object whose size falls in between the minimum (blue shape) and maximum (white shape) range. 3. Use the Sensitivity slidebar to define how sensitive the detection should be.
AXIS Q6045-E Mk II PTZ Dome Network Camera Applications Applications AXIS Camera Application Platform (ACAP) is an open platform that enables third parties to develop analytics and other applications for Axis products. For information about available applications, downloads, trials and licenses, go to www.axis.com/applications Note • Several applications can run at the same time but some applications might not be compatible with each other.
AXIS Q6045-E Mk II PTZ Dome Network Camera Applications If the Axis product is reset to factory default, uploaded applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings.
AXIS Q6045-E Mk II PTZ Dome Network Camera Events Events The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.
AXIS Q6045-E Mk II PTZ Dome Network Camera Events • • • • - Live Stream Accessed – Trigger the rule when any stream is accessed and during edge storage playback. This can for example be used to send notifications. - Motion Detection – Trigger the rule when motion is detected. See Motion Detection on page 32. - Shock Detection – Trigger the rule when the Axis product detects it has been tilted or hit. See Shock Detection on page 32.
AXIS Q6045-E Mk II PTZ Dome Network Camera Events - • • Recording – Triggers the rule when the Axis product records to the storage device. The recording status trigger can be used to notify the operator, for example by flashing LED lights, if the product has started or stopped to record to the storage device. Note that, this trigger can be used only for edge storage recording status. System - System Ready – Trigger the rule when the product has been started and all services are running.
AXIS Q6045-E Mk II PTZ Dome Network Camera Events Recipient Types The following recipients are available: Recipient Use with action Notes Email Send Images An email recipient can contain multiple email addresses. Send Notification Send Video Clip FTP Send Images Send Video Clip SFTP Send Images Encrypted file transfer using SSH File Transport Protocol (SFTP). SFTP is a more secure method than FTP but file transfer might be slower, especially for large files such as high resolution video.
AXIS Q6045-E Mk II PTZ Dome Network Camera Events 3. Enter the email addresses to send emails to in the To field. Use commas to separate multiple addresses. 4. Select the email provider from the Provider list. 5. Enter the user ID and password for the email account. 6. Click Test to send a test email. To set up an email recipient using for example a corporate email server, follow the instructions above but select User defined as Provider. Enter the email address to appear as sender in the From field.
AXIS Q6045-E Mk II PTZ Dome Network Camera Events Connect the Cable CAUTION Modifications could have a negative effect on the electromagnetic compatibility (EMC) of the whole system. Take appropriate precautions and make sure to properly connect the shield in both ends. 1. Strip the cable. 2. Separate the wires. 3. Cut the alarm device wires (see table below) and connect them to the alarm device.
AXIS Q6045-E Mk II PTZ Dome Network Camera Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 46. • To set up action rules, see page 39. • To access recordings, see Find Recordings on page 45. • To play recordings, see Play Recording on page 45. • To export a recording as a video clip, see Export Video Clip on page 46. • To configure camera controlled storage, see Storage on page 56.
AXIS Q6045-E Mk II PTZ Dome Network Camera Recordings To play a recording, follow these steps: 1. Go to Recordings > List. 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the filters. See also Find Recordings on page 45. 3. Select the recording and click Play. The recording will be played in a new browser window. Export Video Clip Recordings on the SD card or network share can be exported as video clips.
AXIS Q6045-E Mk II PTZ Dome Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the file and click the Upload Language button. Select the new language from the list and click Save.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options To enable HTTPS on the Axis product: 1. Go to System Options > Security > HTTPS 2. Select an HTTPS certificate from the list of installed certificates. 3. Optionally, click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection Policy for the different user groups. 5. Click Save to enable the settings.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options Note Installed certificates, except preinstalled CA certificates, will be deleted if the product is reset to factory default. Preinstalled CA certificates that have been deleted will be reinstalled. A Server/Client certificate can be self-signed or issued by a Certificate Authority (CA). A self-signed certificate offers limited protection and can be used before a CA-issued certificate has been obtained. To install a self-signed certificate: 1.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options Network Basic TCP/IP Settings The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled. IPv4 Address Configuration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options ping -l 408 -t Windows example (this may require that you run the command prompt as an administrator) arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125 4. Check that the network cable is connected and then restart the product by disconnecting and reconnecting power. 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar. 6.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options Domain name - Enter the domain(s) to search for the host name used by the Axis product. Multiple domains can be separated by semicolons. The host name is always the first part of a fully qualified domain name, for example, myserver is the host name in the fully qualified domain name myserver.mycompany.com where mycompany.com is the domain name. Primary/Secondary DNS server - Enter the IP addresses of the primary and secondary DNS servers.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options Note • For NAT traversal to work, this must be supported by the router. The router must also support UPnPTM. • In this context, router refers to any network routing device such as a NAT router, Network router, Internet Gateway, Broadband router, Broadband sharing device, or a software such as a firewall. Enable/Disable - When enabled, the Axis product attempts to configure port mapping in a NAT router on your network, using UPnPTM.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention. For more information about AXIS Video MIB and to download MIB files, go to www.axis.com/techsup To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page. Depending on the level of security required, select the version on SNMP to use.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options Bonjour can be disabled under System Options > Network > Bonjour. Storage SD Card NOTICE TICE NO To prevent data corruption, the SD card should be unmounted before removal. Note For SD card recommendations see www.axis.com The Axis product supports SD/SDHC/SDXC cards. The following SD card file systems are supported: • ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options Important If autoformat is enabled, only use new or empty SD cards. Any data stored on the card will be lost when the card is inserted into the Axis product. To enable automatic formatting, follow these steps: 1. Open the Axis product’s webpages and go to Setup > System Options > Storage. 2. Click SD Card. 3. Under General Settings, select Autoformat to. 4. Click OK to save settings.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options Click Restart to perform a correct restart if the Axis product is not behaving as expected. This will not affect any of the current settings. Note A restart clears all entries in the Server Report. Click Restore to reset most settings to the factory default values. The following settings are not affected: • the boot protocol (DHCP or static) • the static IP address • the default router • the subnet mask • the system time • the IEEE 802.
AXIS Q6045-E Mk II PTZ Dome Network Camera System Options Crash Report - Generates an archive with debugging information. The report takes several minutes to generate. Advanced Scripting Scripting allows experienced users to customize and use their own scripts. NOTICE TICE NO Improper use may cause unexpected behavior and loss of contact with the Axis product. Axis strongly recommends that you do not use this function unless you understand the consequences.
AXIS Q6045-E Mk II PTZ Dome Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS Q6045-E Mk II PTZ Dome Network Camera Troubleshooting 5. Reinstall the product, referring to the Installation Guide. If the emergency recovery procedure does not get the product up and running again, contact Axis support at www.axis.com/techsup/ Symptoms, Possible Causes and Remedial Actions Problems setting the IP address When using ARP/Ping Try the installation again. The IP address must be set within two minutes after power has been applied to the product. Ensure the Ping length is set to 408.
AXIS Q6045-E Mk II PTZ Dome Network Camera Troubleshooting Problems with streaming H.264 Problems with AXIS Media Control (Internet Explorer only) To enable the updating of video images in Internet Explorer, set the browser to allow ActiveX controls. Also, make sure that AXIS Media Control is installed on your computer. No H.264 displayed in the client Check that the relevant H.264 connection methods and correct interface are enabled in the AMC Control Panel (streaming tab).
AXIS Q6045-E Mk II PTZ Dome Network Camera Troubleshooting Storage and disk management problems Storage disruption A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other read or write problems occur. To identify the source of the problem, check the System Log under System Options > Support > Logs & Reports. Depending on the problem, it might be necessary to re-mount the storage device.
AXIS Q6045-E Mk II PTZ Dome Network Camera Technical Specifications Technical Specifications Models AXIS Q6045-E Mk II 60 Hz AXIS Q6045-E Mk II 50 Hz Camera Image sensor 1/2.8” Progressive Scan CMOS Lens 4.44–142.6 mm, F1.6–4.41, Horizontal angle of view: 62.8˚–2.23˚, Vertical angle of view: 36.8˚–1.3˚ Autofocus, auto iris Day and night Automatically removable infrared-cut filter Minimum illumination Color: 0.3 lux at 30 IRE F1.6 B/W: 0.03 lux at 30 IRE F1.
AXIS Q6045-E Mk II PTZ Dome Network Camera Technical Specifications External output activation Video recording to edge storage Pre- and post-alarm video buffering PTZ preset, Overlay text, Send SNMP trap Data streaming Event data Built-in installation aids Pixel counter Web browser Camera live view Video recording to file (ASF) Customizable HTML pages Windows 8, Windows 7, Windows Vista, Windows XP, Windows Server 2012, Windows Server 2008 DirectX 9c or higher For other operating systems and browsers, s
AXIS Q6045-E Mk II PTZ Dome Network Camera Technical Specifications Performance Considerations When setting up your system, it is important to consider how various settings and situations will affect performance. Some factors affect the amount of bandwidth (the bit rate) required, others can affect the frame rate, and some affect both. If the load on the CPU reaches its maximum, this will also affect the frame rate.
User Manual AXIS Q6045-E Mk II PTZ Dome Network Camera © Axis Communications AB, 2014 - 2015 Ver. M5.6 Date: May 2015 Part No.
