INSTALLATION GUIDE FRANÇAIS AXIS Q6032-C PTZ Dome Network Camera AXIS Q6034-C PTZ Dome Network Camera AXIS Q6035-C PTZ Dome Network Camera ENGLISH AXIS Q60 Series DEUTSCH ITALIANO ESPAÑOL
Legal Considerations Video and audio surveillance can be prohibited by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license. To purchase further licenses, contact your reseller.
Safeguards Please read through this Installation Guide carefully before installing the product. Keep the Installation Guide for further reference. • • • • • • • • This Axis product shall be used in compliance with local laws and regulations. The Axis product should be installed by a trained professional. Observe relevant national and local regulations for the installation. Battery Replacement This Axis product uses a 3.
Cleaning of Dome Cover • • • Be careful not to scratch or damage the dome cover. Do not clean a dome cover that looks clean to the eye and never polish the surface. Excessive cleaning could damage the surface. For general cleaning of a dome cover it is recommended to use a non-abrasive, solvent-free neutral soap or detergent with water and a soft cloth. Rinse well with clean lukewarm water. Dry with a soft cloth to prevent water spotting. Never use harsh detergents, gasoline, benzene or acetone etc.
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 5 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide This Installation Guide provides instructions for installing AXIS Q6032-C/Q6034-C/Q6035-C PTZ Dome Network Camera on your network. For all other aspects of using the product, please see the User Manual, available at www.axis.com 1. 2. 3. 4. Check the package contents against the list below. Hardware overview. See page 6. Install the hardware. See page 13. Access the Axis Product. See page 21.
Page 6 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Hardware Overview Sunshield Screw hole (3x) Hole for unit holder (3x) Part number (P/N) & Serial number (S/N). The serial number may be required during the installation.
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 7 Camera unit Fan ENGLISH Cooling system (See page 22 for cleaning instructions.
Page 8 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Media converter switch Ground screw Multi-connector cable Power connector (DC input) I/O connector (external) Power connector (DC output) Network connector (internal) I/O connector (internal) Power LED indicator Network LED indicator (4x) ETH 1/2/3/4 Camera LED indicator Network connector SFP (external) (2x) Network connector RJ-45 (external) (2x)
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 9 Connectors Camera SD card slot - A standard or high capacity SD card (not included) can be used for local recording with removable storage. To insert and remove the SD card, the dome cover must be removed, see Install an SD Card (not included), on page 14. ENGLISH To prevent corruption of recordings, the SD card should be unmounted before it is ejected. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.
Page 10 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Network connector SFP (external) - Two SFP connectors (100Base-FX/1000Base-X) for network connectivity. Each RJ-45 and SFP connector has its own dip switch. The dip switches control how the port forwards data. See the User Manual for more information. Dip switch position Description of use Default (middle) B When connecting to the network, directly or through a router or network switch.
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 11 I/O connector (internal) - 2-pin I/O terminal block.
Page 12 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Multi-Connector Cable The supplied multi-connector cable is required in order to maintain the camera’s IP rating. 1 2 8 7 9 3 6 4 5 Connect the multi-connector cable to the camera’s multi-connector and to the connectors in the supplied media converter switch, see illustrations on page page 6 and page 8.
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 13 Electrical Specifications Unit Function Description Network camera Input Power 65 W (min) Media converter switch Input Voltage 12.0 - 13.2 V DC Input Current 6.25 A (min) Input Power 75 W (min) Available Output Power 70 W (min) Nominal Output Voltage 12.5 V DC Media converter switch Multi-connector cable 75 W 65 W 70 W Camera LED Indicators Color Indication Unlit Connection and normal operation. Amber Steady during startup.
Page 14 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Install the Hardware • • This product has a dehumidifying membrane to maintain low humidity levels inside the dome. To avoid condensation, do not disassemble the product in rain or in damp conditions. Be careful not to scratch or damage the dome cover. If possible, keep the protective plastic on the dome cover until the installation is complete.
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 15 8. Put the dome ring with the dome cover back in the original position and tighten the screws (torque 4 Nm). Make sure to align the bulge on the dome cover with the cooling system on the camera unit. Dome cover ENGLISH Cooling system Install an SD Card (not included) Installing a standard or high capacity SD card (not included), which can be used for local recording with removable storage, is optional. 1.
Page 16 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Install the Power Supply and the Media Converter Switch The supplied media converter switch enables the multi-connector cable to send power from the power supply (sold separately) and to send and receive data to and from external alarm devices and the network.
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 17 4. Strip the multi-connector cable. Make sure all three shields are intact. 40 m m (1 .57” ) Shield Shield (2x) ) 1 2 3 4 5 6 7 8 9 1 Red Power 2 Blue Digital I/O 3 Green/white Ethernet 4 Green Ethernet 5 Orange/white Ethernet 6 Orange Ethernet 7 Yellow Digital I/O 8 Black Ground 9 Red Power 5.
Page 18 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Power connector (DC output) 1 9 8 Clamp Shield Shield (2x) I/O connector (internal) 3 7 2 4 Ethernet connector (internal) 6 5 Ethernet connector (internal) 7. Make sure the clamp is in place and tighten the screws. • • The shield and the clamp surface shall be in full contact with each other so that the multiconnector cable is grounded. Make sure all surfaces and contacts are clean and free from scrap shield material.
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 19 8. Connect the network cables to the external network connectors (RJ-45, SFP) as required. Ground screw Power cable (DC input) Multi-connector cable Power connector (DC input) ENGLISH I/O connector (external) Network connector SFP (external) (2x) Network connector RJ-45 (external) (2x) 9. If applicable, connect an I/O device to the external I/O connector. 10. Connect the power cable (DC input) to the power connector (DC input). 11.
Page 20 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide 12. If connecting several media converter switches in a daisy chain, set the dip switch of each outgoing network connector port that connects to another media converter switch to position C. Leave the dip switch in its default position (position B) when connecting the port directly to the network, see Media Converter Switch, on page 9 and the User Manual for more information.
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 21 Install the Network Camera The supplied multi-connector cable shall be used to comply with the IP66 rated design of the camera. Slot for unit holders (3x) Screw (x3) Safety wire Multi-connector cable Alignment indicator Alignment indicator Mounting example, wall bracket sold separately 6. Slide the unit holders on the camera into the slots on the bracket and rotate the camera unit. 7.
Page 22 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Access the Axis Product Use the software provided on the Installation and Management Software CD to assign an IP address, set the password and access the video stream. The Live View Page The product’s Live View page appears in your browser. Click Setup to open the product’s Setup pages, which allow you to customize the Axis product. Setup - Provides all the tools for configuring the product to requirements.
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 23 Cleaning of Outer Heat Sink Dust and particle buildup could affect the performance of the cooling system. To maintain the performance level, the outer heat sink in the camera’s cooling system may need occasional or regular cleaning. The heat sink may be hot, be careful when touching the heat sink and the heat sink cover. Screw (3x) Sunshield 3. Remove the screws (Torx T30) and lift the heat sink cover.
Page 24 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide 4. Remove dust and specks of dirt by blowing on the heat sink, for example by using a small air compressor or a can of compressed air. The heat sink may also be rinsed with clean water. 5. Put the heat sink cover back in its original position and tighten the screws (torque 2.4 ±0.2 Nm). 6. Put the sunshield back in its original position and tighten the screws (torque 1.2 ±0.1 Nm). 7. Connect the multi-connector cable to the connector on the camera.
Installation Guide AXIS Q6032-C/Q6034-C/Q6035-C © Axis Communications AB, 2012 Ver.1.3 Printed: October 2012 Part No.
