AXIS Q2901-E Temperature Alarm Camera User Manual
About this Document This manual is intended for administrators and users of AXIS Q2901-E Temperature Alarm Camera, and is applicable to firmware 5.55 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be beneficial, for developing shell scripts and applications. Later versions of this document will be posted to the Axis website, as required.
있습니다. 적절히 접지된 STP (shielded twisted pair) 케이 블을 사용하여 제품을 연결 하십시오. Safety This product complies with IEC/EN/UL 60950-1 and IEC/EN/UL 60950-22, Safety of Information Technology Equipment. The product shall be grounded either through a shielded network cable (STP) or other appropriate method. The power supply used with this product shall fulfill the requirements for Safety Extra Low Voltage (SELV) and Limited Power Source (LPS) according to IEC/EN/UL 60950-1.
AXIS Q2901-E Temperature Alarm Camera Table of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Access the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Access from a Browser . . .
AXIS Q2901-E Temperature Alarm Camera Table of Contents Check the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Upgrade the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Symptoms, Possible Causes and Remedial Actions . . . . . . . . . . . . . . . . . . . . . Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors . . . . . . . . . . . . . . . . . . .
AXIS Q2901-E Temperature Alarm Camera Hardware Overview Hardware Overview 1 2 3 8 7 4 1 2 3 4 5 6 7 8 5 6 Power connector I/O and audio terminal connector Network connector Status indicator LED MicroSD memory card slot Control button Foot Mounting bracket Connectors and Buttons For technical specifications, see page 63. Network Connector RJ45 Ethernet connector with Power over Ethernet (PoE).
AXIS Q2901-E Temperature Alarm Camera Hardware Overview • Input/Output (I/O) devices When connecting external equipment, a multi-connector cable (available from Axis) is required in order to maintain the product’s IP rating. For more information, see Multi-Connector Cable (sold separately) on page 58. Power Connector 2-pin terminal block for power input.
AXIS Q2901-E Temperature Alarm Camera Access the Product Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are • Internet Explorer® with Windows® • Safari® with OS X® and • ChromeTM or Firefox® with other operating systems. See Technical Specifications on page 63.
AXIS Q2901-E Temperature Alarm Camera Access the Product Set the Root Password To access the Axis product, you must set the password for the default administrator user root. This is done in the Configure Root Password dialog, which opens when the product is accessed for the first time. To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate.
AXIS Q2901-E Temperature Alarm Camera Access the Product The Audio clip drop-down list allows you to play an audio clip from the Live View page. Select the audio clip and click the Play button. The product’s heater is controlled by the ambient temperature and is turned on and off automatically. If required, the heater can be activated manually by clicking the Heater button. To show the button, go to Setup > Live View Config.
AXIS Q2901-E Temperature Alarm Camera Access the Product Speaker button — Click to turn the speakers on or off. Microphone button – Click to mute or unmute the microphone. In Simplex - speaker only mode, the Microphone and Talk buttons must both be active to send audio to the Axis product. Click either button to stop audio transmission. Use the slider to control the volume of the speakers and the microphone. Half-duplex mode The Talk/Listen button is used to switch between sending and receiving audio.
AXIS Q2901-E Temperature Alarm Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream profiles. Other applications and clients can access video and audio streams directly, without going via the Live View page. How to Stream H.264 H.
AXIS Q2901-E Temperature Alarm Camera Media Streams The AMC Control Panel can be used to configure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: • Windows Control Panel (from the Start screen or Start menu) • Alternatively, right-click the video image in Internet Explorer and click Settings.
AXIS Q2901-E Temperature Alarm Camera Media Streams Note • = IP addess • The Axis product supports QuickTime 6.5.1 and later. • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS Q2901-E Temperature Alarm Camera Set Up the Product Set Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to all settings except System Options See also the online help .
AXIS Q2901-E Temperature Alarm Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can configure the following: • Video stream settings. See page 16. • Stream profiles. See page 17. • Camera settings. See page 18. • Overlay image. See page 18. • Privacy mask. See page 20. • Audio settings. See page 20. • Audio clips. See page 22. Set Up Video Streams To set up the product’s video streams, go to Video & Audio > Video Stream.
AXIS Q2901-E Temperature Alarm Camera Video and Audio • Overlay settings. See Overlay on page 18. Click Save to apply the new settings. H.264 H.264, also known as MPEG-4 Part 10/AVC, is a video compression standard that provides high quality video streams at low bit rates. An H.264 video stream consists of different types of frames such as I-frames and P-frames. An I-frame is a complete image whereas P-frames only contain the differences from previous frames. The H.
AXIS Q2901-E Temperature Alarm Camera Video and Audio For quick setup, use one of the predefined stream profiles. Each predefined profile has a descriptive name, indicating its purpose. If required, the predefined stream profiles can be modified and new customized stream profiles can be created. To create a new profile or modify an existing profile, go to Setup > Video & Audio > Stream Profiles. To select a default stream profile for the Live View page, go to Setup > Live View Config.
AXIS Q2901-E Temperature Alarm Camera Video and Audio Overlay Image An overlay image is a static image superimposed over the video stream. The image, for example a company logo, is used to provide extra information or to mask a part of the image. Use a privacy mask to set up a dynamic mask which will always mask the specified part of monitored area. For more information about privacy masks, see Privacy Mask on page 20. To use an overlay image, the image must first be uploaded to the Axis product.
AXIS Q2901-E Temperature Alarm Camera Video and Audio 2. Under Overlay Settings, select Include text. 3. Enter the modifier #D and, optionally, additional text which will be displayed also when the action rule is not active. Create the action rule: 1. Go to Events > Action Rules 2. Click Add to create a new rule. 3. Select a Trigger and, optionally, a Schedule and Additional conditions. See the online help for details. 4. From the Actions list, select Overlay Text 5.
AXIS Q2901-E Temperature Alarm Camera Video and Audio Simplex — Network Camera microphone only - Audio captured by the product microphone is transmitted from the Axis product to one or more clients. To set the audio mode, go to Video & Audio > Audio Settings and select the desired mode from the Audio mode drop-down list. Audio Input Select Microphone to use an external microphone or Line to use a Line in device, e.g.
AXIS Q2901-E Temperature Alarm Camera Video and Audio Audio Clips An audio clip is a sound file that can be played when events occur or directly from the Live View page. The audio clip must first be uploaded to the Axis product or recorded by a microphone connected to the product. To add, download, modify or remove audio clips, go to Video & Audio > Audio Clips. For more information see the online help To configure the Axis product to play audio clips when an event occurs, an action rule must be set up.
AXIS Q2901-E Temperature Alarm Camera Thermal Settings Thermal Settings The thermal settings can be used to configure isothermal settings and set the temperature scale. • Isothermal settings. See page 23. • Temperature scale. See page 25. Isothermal Settings Isothermal settings are used to configure the colors in the image that visually highlight temperature differences.
AXIS Q2901-E Temperature Alarm Camera Thermal Settings 28˚C 28˚C 28˚C 28˚C 28˚C 28˚C 28˚C 25˚C 25˚C 25˚C 25˚C 25˚C 25˚C 25˚C 22˚C 22˚C 22˚C 22˚C 22˚C 22˚C 22˚C b a a b c d e f g c d e f Iso-Fire-WH Iso-Fire-BH Iso-Planck-WH Iso-Axis-WH Iso-Midrange-WH Iso-Midrange-BH Iso-Rainbow-WH Set up Palette To set up a palette to highlight temperature differences in the image: 1. Go to Thermal Settings > Isothermal Settings 2. Select a palette in the Palette drop-down-menu. 3.
AXIS Q2901-E Temperature Alarm Camera Thermal Settings Temperature Scale Temperature data can be displayed in either Celsius or Fahrenheit. Select the temperature unit and click Save to apply the setting. The Axis product can automatically convert all temperature values that you have entered into the selected temperature scale.
AXIS Q2901-E Temperature Alarm Camera Configure the Live View Page Configure the Live View Page You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features of the Live View page. • Stream Profile. See page 17. • Default Viewer for Browser. See page 26. • Viewer Settings. See page 26. • Action Buttons. These are the buttons described in Controls on the Live View Page on page 9 . • Temperature Settings.
AXIS Q2901-E Temperature Alarm Camera Configure the Live View Page • Select Enable recording button to enable recording from the Live View page. This button is available when using the AMC viewer. The recordings are saved to the location specified in the AMC Control Panel. See AXIS Media Control (AMC) on page 12. Temperature Settings To configure temperature settings, go to Live View Layout > Temperature Settings • Show Temperature Zones: Shows the created temperature zones on the Live View page.
AXIS Q2901-E Temperature Alarm Camera Detectors Detectors Temperature Detection Temperature detection is used to generate an alarm whenever the temperature changes according to defined conditions: • The temperature rises above a specified temperature • The temperature falls below a specified temperature • The temperature increases above a specified rate Temperature detection is set by configuring up to six temperature detection zones in the camera view.
AXIS Q2901-E Temperature Alarm Camera Detectors - Below (B): Triggers if the temperature falls below the level (C) that you have set in the Detection Temperature field. By default, minimum temperature in the zone is used as the base for temperature detection. + 000 000 000 000 A B C 000 000 000 000 000 B 00000 00000 - Increase:Triggers if the temperature (E) increases faster than the increase rate (F) during an increase time interval (for example, in the time between t1 and t2).
AXIS Q2901-E Temperature Alarm Camera Detectors + - E G D D D D G G G + - G F F F D D F D D t1 t0 + - D: E: F: G: t2 t3 t4 F Actual temperature increase in the zone Temperature in the zone Your temperature increase rate, expressed in degrees (°C or °F) per seconds Measurement point that triggers or untriggers an alarm Note By default, maximum temperature in the zone is used as the base for detection type Increase.
AXIS Q2901-E Temperature Alarm Camera Detectors 6. For detection type Increase: Enter the increase rate (F) in degrees per seconds in the Increase rate fields. - The Y-axis: the degrees in Celsius or Fahrenheit - The X-axis: the increase time in seconds F + - 7. Click Save to save your settings or continue to the Advanced Settings section to set additional detection conditions. Advanced Settings 1. In a temperature detection zone: Select Advanced Settings to show additional detection settings. 2.
AXIS Q2901-E Temperature Alarm Camera Detectors + 000 A 000 C 000 0 B 000 0 000 000 D D t0 t1 t2 t3 t4 4. If detection type Above (A) or Below (B) is selected: Enter a Delay Time (D) in seconds. Note Alarms are triggered after the Delay time (D) has elapsed. In the example, an Above alarm is triggered between t1 and t2. A Below alarm is triggered between t3 and t4. 5. Click Save to save your settings. Show and Hide Detection Zones • To view all the detection zones, select View All Zones.
AXIS Q2901-E Temperature Alarm Camera Detectors Material Emissivity Asphalt 0.93 Charcoal 0.96 Cloth 0.95 Concrete 0.94 Foodstuff 0.80-0.90 Graphite 0.97 Metals (unoxidized) <0.10 Oil paint (value may vary depending on paint types) 0.92-0.96 Paints (value may vary depending on color) 0.90-0.96 Plastics (value may vary depending on surface finish and paint types) 0.92-0.95 Porcelain (glazed) 0.92 Rubber(hard) 0.94 Rubber(soft) 0.86 Skin (human) 0.98 Soil 0.93 0.95-0.
AXIS Q2901-E Temperature Alarm Camera Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Motion Detection Window. Set Up Motion Detection Windows To set up a motion detection Include Window, follow these instructions: 1. Go to Detectors > Motion Detection. 2.
AXIS Q2901-E Temperature Alarm Camera Detectors 2. Set the audio alarm level and click Save. 3. Go to Events > Action Rules and set up an action rule, see Set Up Action Rules on page 38. Detected audio is indicated by colored peaks in the Activity indicator. An event is triggered when detected audio rises above or falls below the threshold value, which is represented by the bar.
AXIS Q2901-E Temperature Alarm Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, downloads, trials and licenses, go to www.axis.com/applications Note • It is recommended to run one application at a time.
AXIS Q2901-E Temperature Alarm Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings. AXIS Video Motion Detection The application AXIS Video Motion Detection is included in this product. AXIS Video Motion Detection is an application that detects moving objects in the camera’s field of view.
AXIS Q2901-E Temperature Alarm Camera Events Events The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.
AXIS Q2901-E Temperature Alarm Camera Events • • • • • - Live Stream Accessed – Trigger the rule when any stream is accessed and during edge storage playback. This can for example be used to send notifications. - Motion Detection – Trigger the rule when motion is detected. See Motion Detection on page 33. - Shock Detection – Trigger the rule when the Axis product detects it has been tilted or hit. See Shock Detection on page 33.
AXIS Q2901-E Temperature Alarm Camera Events • Output Port – Activate an I/O port to control an external device. • Overlay Text – Display an overlay text. See Use Overlay Text in an Action Rule on page 19. • Play Audio Clip – See Audio Clips on page 22. • Record Video – Record video and audio to a selected storage. To record audio, use AAC audio encoding and make sure that audio is enabled in the selected stream profile. • Send Images – Send images to a recipient.
AXIS Q2901-E Temperature Alarm Camera Events address, port and authentication method. Optionally, select Use encryption to send emails over an encrypted connection. The server certificate can be validated using the certificates available in the Axis product. For information on how to upload certificates, see Certificates on page 46. Create Schedules Schedules can be used as action rule triggers or as additional conditions, for example to record video if motion is detected outside office hours.
AXIS Q2901-E Temperature Alarm Camera Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 42. • To set up action rules, see page 38. • To access recordings, see Recording List on page 42. • To configure camera controlled storage, see Storage on page 53. Recording List Recorded videos are listed on the Recordings > List page.
AXIS Q2901-E Temperature Alarm Camera Recordings 5. Click Save to save and start the recording.
AXIS Q2901-E Temperature Alarm Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the file and click the Upload Language button. Select the new language from the list and click Save.
AXIS Q2901-E Temperature Alarm Camera System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS Q2901-E Temperature Alarm Camera System Options 3. Optionally, click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection Policy for the different user groups. 5. Click Save to enable the settings. To access the Axis product via the desired protocol, in the address field in a browser, enter https:// for the HTTPS protocol and http:// for the HTTP protocol. The HTTPS port can be changed on the System Options > Network > TCP/IP > Advanced page. IEEE 802.1X IEEE 802.
AXIS Q2901-E Temperature Alarm Camera System Options To install a self-signed certificate: 1. Go to Setup > System Options > Security > Certificates. 2. Click Create self-signed certificate and provide the requested information. To create and install a CA-signed certificate: 1. Create a self-signed certificate as described above. 2. Go to Setup > System Options > Security > Certificates. 3. Click Create certificate signing request and provide the requested information. 4.
AXIS Q2901-E Temperature Alarm Camera System Options Network Basic TCP/IP Settings The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled. IPv4 Address Configuration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.
AXIS Q2901-E Temperature Alarm Camera System Options ping -l 408 -t Windows example (this may require that you run the command prompt as an administrator) arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125 4. Check that the network cable is connected and then restart the product by disconnecting and reconnecting power. 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar. 6.
AXIS Q2901-E Temperature Alarm Camera System Options Domain name - Enter the domain(s) to search for the host name used by the Axis product. Multiple domains can be separated by semicolons. The host name is always the first part of a fully qualified domain name, for example, myserver is the host name in the fully qualified domain name myserver.mycompany.com where mycompany.com is the domain name. Primary/Secondary DNS server - Enter the IP addresses of the primary and secondary DNS servers.
AXIS Q2901-E Temperature Alarm Camera System Options Note • For NAT traversal to work, this must be supported by the router. The router must also support UPnPTM. • In this context, router refers to any network routing device such as a NAT router, Network router, Internet Gateway, Broadband router, Broadband sharing device, or a software such as a firewall. Enable/Disable - When enabled, the Axis product attempts to configure port mapping in a NAT router on your network, using UPnPTM.
AXIS Q2901-E Temperature Alarm Camera System Options SMTP (email) To send email messages from the Axis product via SMTP (Simple Mail Transfer Protocol), an SMTP mail server must be set up. This is done under System Options > Network > SMTP (email). Enter the host names or IP addresses and port numbers for the primary and secondary mail servers in the fields provided. A From email address is also required.
AXIS Q2901-E Temperature Alarm Camera System Options Bonjour The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol. Bonjour can be disabled under System Options > Network > Bonjour. Storage SD Card NOTICE TICE NO To prevent data corruption, the SD card should be unmounted before removal. Note For SD card recommendations see www.axis.
AXIS Q2901-E Temperature Alarm Camera System Options The Axis product can be configured to automatically format SD cards that are inserted into the product. If autoformat is enabled and an SD card is inserted, the product will check if the SD card has the ext4 file system. If the card has a different file system, the card will automatically be formatted to ext4. Important If autoformat is enabled, only use new or empty SD cards.
AXIS Q2901-E Temperature Alarm Camera System Options Ports & Devices I/O Ports Port Status The list on the System Options > Ports & Devices > Port Status page shows the status of the product’s input and output ports. Maintenance The Axis product provides several maintenance functions. These are available under System Options > Maintenance. Click Restart to perform a correct restart if the Axis product is not behaving as expected. This will not affect any of the current settings.
AXIS Q2901-E Temperature Alarm Camera System Options Logs & Reports The System Options > Support > Logs & Reports page generates logs and reports useful for system analysis and troubleshooting. If contacting Axis Support, please provide a valid Server Report with your query. System Log - Provides information about system events. Access Log - Lists all failed attempts to access the product. The Access Log can also be configured to list all connections to the product (see below).
AXIS Q2901-E Temperature Alarm Camera System Options Reset to Factory Default Settings Important Reset to factory default should be used with caution. A reset to factory default will reset all settings, including the IP address, to the factory default values. Note The installation and management software tools are available on the CD supplied with the product and from the support pages on www.axis.com/techsup To reset the product to the factory default settings: 1. Disconnect power from the product. 2.
AXIS Q2901-E Temperature Alarm Camera Multi-Connector Cable (sold separately) Multi-Connector Cable (sold separately) When connecting external equipment to the Axis product, a multi-connector cable (available from Axis) is required in order to maintain the product’s IP rating. The multi-connector cable can be purchased from your Axis reseller. Connect the multi-connector cable to the product’s multi-connector. To locate the multi-connector, see Hardware Overview on page 6 .
AXIS Q2901-E Temperature Alarm Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS Q2901-E Temperature Alarm Camera Troubleshooting 5. Reinstall the product, referring to the Installation Guide. If the emergency recovery procedure does not get the product up and running again, contact Axis support at www.axis.com/techsup/ Symptoms, Possible Causes and Remedial Actions Problems setting the IP address When using ARP/Ping Try the installation again. The IP address must be set within two minutes after power has been applied to the product. Ensure the Ping length is set to 408.
AXIS Q2901-E Temperature Alarm Camera Troubleshooting Problems with streaming H.264 Problems with AXIS Media Control (Internet Explorer only) To enable the updating of video images in Internet Explorer, set the browser to allow ActiveX controls. Also, make sure that AXIS Media Control is installed on your computer. No H.264 displayed in the client Check that the relevant H.264 connection methods and correct interface are enabled in the AMC Control Panel (streaming tab).
AXIS Q2901-E Temperature Alarm Camera Troubleshooting Poor audio quality Stuttering Reduce the number of listeners and viewers. Decrease image resolution and compression. Unsynchronized audio and video using H.264 Synchronize the product’s date and time settings with an NTP server. Go to Setup > System Options > Date & Time. Distorted audio Check that the correct Audio Input source is selected under Setup > Video & Audio > Audio Settings.
AXIS Q2901-E Temperature Alarm Camera Technical Specifications Technical Specifications Function/group Item Specifications Camera Model AXIS Q2901–E Image sensor Uncooled Micro bolometer 336x256 pixels, pixel size 17 µm Spectral range: 8-14 µm Lens 9 mm: f 1.25 FoV horizontal 35°, vertical 27°; min. focus distance: 2.1 m (78.7 in) 19 mm: f 1.25 FoV horizontal 17°, vertical 13°; min. focus distance: 9.5 m (354.
AXIS Q2901-E Temperature Alarm Camera Technical Specifications Function/group Item Specifications Network Security Password protection, IP address filtering, IEEE 802.1X* network access control, HTTPS* encryption, digest authentication, user access log, centralized certificate management. Supported protocols IPv4/v6, HTTP, HTTPS*, SSL/TLS*, QoS Layer 3 DiffServ, FTP, SMTP, Bonjour, UPnP™, SNMPv1/v2c/v3(MIB-II), DNS, DynDNS, NTP, RTSP, RTP, TCP, UDP, IGMP, RTCP, ICMP, DHCP, ARP, SOCKS, CIFS/SMB, SSH.
AXIS Q2901-E Temperature Alarm Camera Technical Specifications Function/group Item Specifications Operating conditions Temperature: -40 ºC to 60 ºC (-40 ºF to 140 ºF) Humidity: 10-85% RH (condensing) Storage conditions -40 ºC to 70 ºC (-40 ºF to 158 ºF) Approvals EN 55022 Class B EN 50121-4 EN 61000-3-2 EN 61000-3-3 EN 61000-6-1 EN 61000-6-2 FCC part 15 Subpart B Class B ICES-003 Class B VCCI Class B, ITE C-Tick AS/NZS CISPR22 Class B KCC KN22 Class B, KN-24 IEC/EN/UL 60950-1, IEC/EN/UL 60950-22 EN
AXIS Q2901-E Temperature Alarm Camera Technical Specifications Connectors Power Connector 2-pin terminal block for power input. Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A. DC power input Important If a DC power supply is used to power the product, the low voltage power cord shall be equipped with a ferrite core. SD Card Slot Supports microSD cards with up to 64 GB of storage.
User Manual AXIS Q2901-E Temperature Alarm Camera © Axis Communications AB, 2014 Ver. M1.13 Date: February 2015 Part No.
