Installation guide

ManualsBrandsAxis ManualsNetworkingM7016

Table Of Contents

INSTALLATIONGUIDE

AXISM7016VideoEncoder

ENGLISH

Summary of content (14 pages)

PAGE 1
INSTALLATION GUIDE ENGLISH AXIS M7016 Video Encoder
PAGE 2
Legal Considerations Support Video surveillance can be regulated by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license. To purchase further licenses, contact your reseller. Should you require any technical assistance, please contact your Axis reseller.
PAGE 3
Europe This digital equipment fulfills the requirements for RF emission according to the Class B limit of EN 55022. This product fulfills the requirements for immunity according to EN 61000-6-1 residential, commercial and light-industrial environments. This product fulfills the requirements for immunity according to EN 61000-6-2 industrial environments. Australia/New Zealand This digital equipment fulfills the requirements for RF emission according to the Class B limit of AS/NZS CISPR 22.
PAGE 4
PAGE 5
AXIS M7016 Video Encoder Safety Information Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE Indicates a situation which, if not avoided, could result in damage to property.
PAGE 6
AXIS M7016 Video Encoder Safety Instructions NOTICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing. • Store the Axis product in a dry and ventilated environment. • Avoid exposing the Axis product to vibration, shocks or heavy pressure. • Do not install the product on unstable or vibrating brackets, surfaces or walls.
PAGE 7
AXIS M7016 Video Encoder Installation Guide Installation Steps 1. Make sure the package contents, tools and other materials necessary for the installation are in order. See page 7 . 2. Study the hardware overview. See page 7 . 3. Study the specifications. See page 9 . 4. Install the hardware. See page 11. 5. Access the product. See page 11.
PAGE 8
AXIS M7016 Video Encoder 2 3 4 5 6 Network connector RJ45 Card slot microSD x4 RS-485/422 connector x4 Control button x4 Protective earth 1 1 2 3 4 2 3 4 Video input connector BNC x16 Status LED 1–4 Power LED Network activity LED RJ45 LED Indicators LED Color Indication Network Green Steady for connection to a 1 GBit/s network. Flashes for network activity. Amber Steady for connection to a 10/100 MBit/s network. Flashes for network activity. Unlit No network connection.
PAGE 9
AXIS M7016 Video Encoder Note Network connector - RJ45 Ethernet connector. NOTICE The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch shall be shielded (STP) and intended for their specific use. Make sure that the network switch is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2 .
PAGE 10
AXIS M7016 Video Encoder Product Temperature Humidity AXIS M7016 0 °C to 50 °C (32 °F to 122 °F) 20-80% RH (non-condensing Power Consumption Product Power supply AXIS M7016 AXIS PS-P power supply Connectors Power connector DC power input 2-pin terminal block for power input. Use a limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A. RS-485/422 connector Two 2-pin terminal blocks for RS485/RS422 serial interface.
PAGE 11
AXIS M7016 Video Encoder RS485/RS422 TX A 3 RS485/RS422 TX B 4 (TX) For full duplex RS485/RS422 ENGLISH Install the Hardware Mount the video encoder The AXIS M7016 is supplied with a mounting kit containing brackets. The unit can be mounted in a rack or on a wall. After removing the existing 4 screws, attach the mounting brackets to the video encoder at an angle suitable for installation in a standard 1U 19” rack, or on the wall. Mounting on a wall 1.
PAGE 12
AXIS M7016 Video Encoder Note To reset a single channel to the original factory default settings, use the button provided in that unit’s web interface. It is also possible to reset parameters to factory default via the web interface. Go to Setup > System Options > Maintenance. Further Information The User Manual is available at www.axis.com Visit www.axis.com/techsup to check if there is updated firmware available for your network product.
PAGE 13