User`s manual

Appendix A: Parameter List
AXIS StorPoint CD Token Ring - User’s Manual 89
TrapDestination = 0.0.0.0 Specifies the IP address which SNMP traps are sent to. It
corresponds to the trapAddress SNMP object. Default is 0.0.0.0,
i.e. all SNMP traps are disabled.
TrapCommunityName = public Specifies the community for all generated SNMP traps. It
corresponds to the trapCommunity SNMP object.
SystemContact = Optional entry which should be in plain text and may be used to
show the name of the system contact person.
SystemName = Optional entry which should be in plain text and may be used to
show the name of the location of the system.
SystemLocation = Optional entry which should be in plain text and may be used to
show the name of the location of the system.
AuthenticationTrap = disabled Disables the SNMP authentication failure traps. It corresponds to
the snmpenableAuthenTraps (MIB-II) SNMP object.
[NetWare]
NWEnable = yes Enables NetWare support.
IPXEnable = yes Enables the IPX protocol.
Frame_802.2 = auto Enables the 802.2 frame type.
Frame_SNAP = auto Enables the SNAP frame type.
NetWareIP_Enable = no Enables NCP over IPX/UDP (NetWare/IP).
NetWareIP_DSS_Server = The IP address of the DSS server.
PureIPEnable = yes Enables NCP over TCP/IP (PureIP).
ServerName = AXIS<nnnnnn>_NW NetWare server name to be presented to the NetWare clients.
Default is AXIS<nnnnnn>_NW where nnnnnn are the last six digits
of the serial number.
InternalNetAddress = nn-nn-nn-nn Internal network address. Default is nn-nn-nn-nn where nnnnnnnn
are the last eight digits of the serial number.
BurstMode = on Enables burst mode.
ShowAllVolumes = yes Shows all drives and discs also at SYS level.
BinderyEnable = yes Enables bindery mode login. When using NDS, set to no to increase
system security. The Supervisor can always login in bindery mode
even if this parameter is set to no.
BindAuthentication = Name or IP address of the server used for authenitcating clients.
NDSEnable = yes Enables NDS mode.
NDSTreeName = Name of the tree where you wish to install the StorPoint CD.
NDSServerContext = Distinguished name of the context in the NDS tree where you wish
to install the StorPoint CD, e.g. Corp.Acme.
NDSAdminName = Distinguished name of a user or administrator with Supervisor or
Create rights to the context where you want to install StorPoint
CD, e.g. Admin.Acme.
NDSAdminPassword = Password for the administrator defined in NDSAdminName. Once
written into the configuration file, the password will not be shown
but replaced with *’s, representing each letter of the password.
NDSInstall = no Set to install when you are ready to install StorPoint CD in NDS, or
forced to overwrite the NDS server object.
NDSRightsStorage = NDS Set to NDS to store the access rights in the NDS tree. Set to File to
store the access rights in a file on the Novell server. This is
necessary if you do not allow schema extensions in your NDS tree,
or if you do not have Supervisor access rights.
NDSRightsFile = If you have set NDSRightsStorage to File, specify the whole path to
the file on the Novell file server using this syntax:
SERVER/VOLUME:DIR/.../FILE.DAT where SERVER is a NetWare
server name or IP address. The specified directory must exist and
StorPoint CD must have Read, Write, Create, Erase, Modify and
File Scan rights. The StorPoint CD will create the file once you
start adding trustees.
TimeSyncSources = SAP For IPX, use SAP or specify a list of time server names to be
contacted for time synchronization. For PureIP and NetWare/IP,
specify a list of server names or IP addresses. Default is SAP for the
network agreed time.
[SMTP]
Primary Mail Server = mail Name or IP address of the primary mail server.
Secondary Mail Server = Name or IP address of the secondary mail server.
Parameter name Value Description